D-Link DCS-5300G Router Manual PDF (Setup & Configuration Guide)

Page 101 / 145 Scroll up to view Page 96 - 100

101

Using IP surveillance Software (continued)

Schedule Tool

Scheduling

The scheduler allows the user to schedule recordings from the selected video

channel of the

DCS-5300G

. Through both the graphic user interface and time

period selection options, you will be able to easily regulate a schedule for each

video channel.

The main features of the Scheduler are:

Friendly graphic user interface for schedule editing

Flexible schedule scheme suitable for all applications

Individual schedule for each video channel

Supports up to 9 preset schedule schemes for each video channel

Automatic period recording

±

Using the Scheduler

This section discusses the method of how to use the scheduler.

Start the Scheduler

Page 102 / 145

102

Using IP surveillance Software (continued)

Part 1

Part 2

Part 3

Part 4

Scheduling (continued)

The scheduler will not be accessible until at least one camera has been added

to the camera list. Go to the configuration menu and click on “Scheduler” to

launch the Scheduler.

The Layout and Functionalities

Introduction

The layout of the scheduler and its components, shown below, will be described.

Page 103 / 145

103

Using IP surveillance Software (continued)

Video channel

IP address

Location

Scheduling (continued)

The layout of the Scheduler is roughly divided into 4 parts:

Part 1

The first part of the scheduler is the video channel selection area.

It provides the IP addresses and location information of the

connected video channels for the user’s reference. You can select

a video channel in this area and create a schedule for it.

Part 2

The second part is the Primary schedule settings. It consists of

the

day time-line,

week time-line,

begin time selector

,

end

time selector

, and event mode settings.

Part 3

The third part is the Secondary schedule, which consists of event

mode settings.

Part 4

The fourth part contains

the operation buttons

for the user to

manipulate the edited schedule of the selected video channel.

The scheduler can be closed from here.

±

The Functionalities of Configuration Components

The four main parts of the scheduler have been briefly described in the section

above. Parts 1-4 will be described in detail in the following section

.

Page 104 / 145

104

Using IP surveillance Software (continued)

Scheduling (continued)

In this area you will select the video channel that you want to set a schedule for.

Each video channel will display a name, IP address, and location. Please note

that when you switch between video channels in this area, the changes in the

schedule of the previous video channel will be saved automatically.

Primary Schedule

Schedule with Time Lines

Week Time-Line

In the figure below, Week time-line is displayed. It includes the time-line, schedule

information, and the selected day in the week.

Selected Day

Marking/Unmarking the Recording Time on the Week Time-Line

Click

Result in hour time-line

There are two different time-lines: hour unit time-line and week unit time-line.

You can make your own schedule by plotting markers in all time-lines. These

two time lines are associated with each other. That is, if you make changes in

one time-line, the corresponding changes will be applied with scale to the other

three time-lines in the same schedule. Before you begin, make sure that you

select “Once” (page 102) if you want to choose the days to record on.

The corresponding changes for the markers on the week time-line will be

automatically added to the hour time-lines, which is shown above. You can

also mark and unmark the plotted bar by clicking and dragging with the left and

the right mouse button.

Page 105 / 145

105

Using IP surveillance Software (continued)

Scheduling (continued)

Hour Time-Line

In the figure below, the Hour time-line is displayed.

Marking/Unmarking the Recording Time on the Hour Time-Line

You can apply the one-click function by clicking the left mouse button and

dragging to mark the time on this time-line. The operating method for the hour

time-line is the same as that of the week time-lines. Please refer to the previous

section about marking/unmarking on the week time-line for more details

.

Schedule with Time Picker

Begin and End Time

Date picker

Hour picker

Minute picker

There are three controlling units in both “Begin Time” and “End Time” selectors

shown above. The first unit of these two selectors is the date picker. You can

select day with it to set the beginning time and the ending time for the recording

interval.

The second and third units are the hour picker and the minute picker. You can

change the hour and minute settings for the beginning and ending time with

them.

NOTE: The time set in “Begin time” must be earlier than that in “End time”.

Otherwise the settings will not be applied.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share