1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DCS-3220G
    5. /
  5. 12
Page 56 / 141 Scroll up to view Page 51 - 55
56
Configuration > Tools > Default
Click on the
Default
button to access the option to restore to factory default
settings.
Click
Apply
on this screen to restore factory default settings. This means
any
changes made will be lost and the system will be reset to the initial status when
shipped from the factory. After confirmation, the system will restart and require
the
Installation Wizard
software program to locate the IP address of the
DCS-
3220
.
Using the DCS-3220 with an Internet browser
(continued)
Click
Apply
to make
changes effective
.
Configuration > Status > Device Info
Click on the
Status
tab to access
Device Info
and a
Log
of
DCS-3220
system
activity. The
Device Info
is the default screen when you click on the
Status
tab.
Click
Default
.
Page 57 / 141
57
The Device Info screen lists the following important settings that are currently
set for the
DCS-3220
.
•
Firmware Version number
•
Mac Address
•
IP Address
•
Subnet Mask
•
Default router address
•
Primary DNS Address
•
Secondary DNS Address
Configuration > Status > Log
Using the DCS-3220 with an Internet browser
(continued)
Click on the
Log
button to access a system log of system activity from the
Status
menu. The content of the log file reveals useful information about the
current configuration and connection logged after the
DCS-3220
boots up.
Click
Device Info
.
Click
Log
.
Page 58 / 141
58
Click on the
Help tab
to access descriptions of the particular function you need
help with. The help screen is organized in the order of the tabs and then each
menu item under that tab.
Configuration > Help
Using the DCS-3220 with an Internet browser
(continued)
Page 59 / 141
59
Administrators can combine options on the application page to perform many
useful security applications. There are two trigger sources available: from an
external sensor or with built-in motion detection. There are also two kinds of
actions that can respond to these events that include uploading snapshots
over the internet and driving attached devices. To upload the snapshots, users
can choose either email or FTP according to user’s needs. Both e-mail and
FTP use the network settings on the network page. This section describes
how to enable motion detection and record snapshots to an FTP server.
If no external sensor is available, administrators can utilize the built-in motion
detection to monitor any abnormal movement and record the snapshots to an
FTP or SMTP server.
In this window, follow the steps below to ensure that motion detection is correctly
enabled:
c
Check “Enable motion detection.”
d
Click on “New” to have a new window to monitor video.
e
Enter in a window name.
f
Tune the “Sensitivity” and “Percentage” according to the local
environment. The highest sensitivity and lowest percentage provides
the most sensitive setting.
5
Click on save to enable the activity display.
Click the
Motion Detection
button under the
Advanced
tab from the
Configuration
screen to access settings that affect how the
DCS-3220
Internet
Camera can serve as a security device by recording only when motion is
detected.
Record Snapshots to your FTP server
with Motion Detection
Click
Motion Detection
.
Back Door
X
Page 60 / 141
60
Next, click the
Network
button under the
Advanced
tab to set the FTP server
settings for the
DCS-3220
.
Record Snapshots to your FTP server with
Motion Detection (continued)
In this window, enter the settings for the FTP server you wish to record to.
Optionally, you can enter settings for a secondary backup FTP server.
Local FTP server port-
The Default port is 21. To connect to an FTP sever,
it is recommended that you do not change the
port number unless your camera is behind a
router. If your camera is behind a router, you can
assign any port number to this field, but you must
enable port forwarding on the router. Please refer
to your router manual for more information on port
forwarding.
1st FTP server-
If you are going to upload snapshots to an FTP
server, you will need to fill in the Domain name or
IP address of your external FTP server such as
ftp://dlink.com or ftp://123.123.123.1. (The server
name and IP address will vary
depending on the
user.) The following user settings must be
correctly configured for remote access.
1
2
Click
Network
John Smith
123.123.123.1
1
2
3
4
Snapshot
5
6
7

Rate

4 / 5 based on 1 vote.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top