Page 31 / 141
Scroll up to view Page 26 - 30
31
Important:
Some ISPs block access to port 80. Be sure to check with your ISP
so that you can open the appropriate ports accordingly. Some ISPs block traffic
on commonly used ports to conserve bandwidth. If your ISP does not pass
traffic on port 80, you will need to change the port the camera uses from 80 to
something else, such as 800. Not all routers are the same, so refer to your
user manual for specific instructions on how to open ports.
Using & Configuring the DCS-3220 with a
NAT Router (continued)
Follow these steps to configure your router’s Virtual Server settings:
Repeat the above steps adding ports
5002
and
5003
to both the
Public
and
Private Port
sections. A check mark appearing before the entry name will
indicate that the ports are enabled.
•
Click
Enabled
.
•
Enter a different name for each entry.
•
Enter your camera’s local IP Address (e.g.,
192.168.0.146
in
the example in step
d
on page 28) in the
Private IP
field.
•
Select
Both
under
Protocol Type
(
TCP
and
UDP
).
•
If you are using the default camera port settings, enter
80
into
the
Public
and
Private
Port
section, click
Apply
.
•
Scheduling
should be set to
Always
so that the camera
images can be accessed at any time.
Enter valid ports in the
Virtual
Servers
section of your router.
Please make sure to check
the box on this line to enable
settings.
Page 32 / 141
32
Viewing Your Camera
After all settings have been entered correctly, a PC user inside or outside your
network will have access to the camera through the Internet Explorer Web
browser. To access the camera from the Internet, type the IP Address of the
router given to you by your ISP, followed by a colon, and the port number that
you gave your camera (e.g.,
). It is not necessary to
enter the colon and port number if you are using the default Web server port 80.
To access from a computer on your local (home) network, simply enter the local
IP Address of the Camera followed by a colon and the port number (e.g.,
205.163.122.96:83
)
.
Viewing the DCS-3220 Remotely
Page 33 / 141
33
Open your Internet Explorer Web browser and enter the IP address for your
Internet Camera.
In the example, this address is 192.168.0.146.
Your address may differ.
If a window appears
asking to install a
Verisign certificate
for authentication
Click
Yes
. This
allows the proprietary
MPEG4 video stream
to be recognized by
Internet Explorer.
If you are following this manual in the order it is presented, you should now have
an operating
DCS-3220
Internet Camera configured with the Installer program.
You also have installed the
IP surveillance
software from the CD. This section
of the manual will deal with using the Internet Camera in two parts:
±
Using
the
DCS-3220
with an Internet browser and accessing
the screens to control and monitor the camera.
±
Using the
IP surveillance
software
with the
DCS-3220
.
Using the DCS-3220 with an
Internet browser
Page 34 / 141
34
Home Page Screen
The image from the
DCS-3220
should be visible from the Home page on your
computer monitor. Below the image are controls that allow you to control zoom
and two way audio functions.
Using the DCS-3220 with an Internet browser
(continued)
Push/Toggle –
Push to enable
the speaker. You can set the
speaker button operation to
either Push or Toggle on the
Connection Type
screen. For
additional information, please
refer to the section titled
Home
> Connections Screen
(page
36).
Speaker Volume Control –
Click to increase or decrease
speaker volume.
Mute Speaker –
Click to mute
the speaker.
Microphone Volume Control –
Click to increase or decrease microphone
volume.
Mute Microphone –
Click to mute the camera’s microphone.
Click the
Zoom
button
below the image to
display the digital zoom
control panel. Using the
bar, you can select to
view the image up to
400% of the original size.
+
–
Opens digital zoom window.
Page 35 / 141
35
Home Page Screen
The image from the
DCS-3220
should be visible from the Home page on your
computer monitor.
Using the DCS-3220 with an Internet browser
(continued)
Click on the
Connection Type
button to change settings related to the
connection.
There are two
buttons on the left
side of the
Home
page:
Connection Type
and
Configuration
.
Click
Connection Type
19216811.live