46

D-Link DCS-1100/1130 User Manual

Appendix A - Installing the DCS-1100/1130 on a Router Without UPnP

Router Setup

The following steps generally apply to any router that you have on your network. The D-Link DIR-301 is used as an

example to clarify the configuration process.

Note

: Because a dynamic WAN IP address can change from time to time depending on your ISP, you may want to

obtain a Static IP address from your ISP. A Static IP address is a fixed IP address that will not change over time and

will be more convenient for you to use to access your camera from a remote location. You can also use DDNS to obtain

an IP address. Please refer to page 23 for more information.

47

D-Link DCS-1100/1130 User Manual

Appendix A - Installing the DCS-1100/1130 on a Router Without UPnP

4) Use Port Forwarding to Enable Remote Image Viewing

You will need to use port forwarding on your router to open ports for remote access to your camera. This is sometimes

referred to as Virtual Server Settings. Please proceed as follows:

• Go to the

Port Forwarding

section of your router.

• Enter a

Name

for the port forwarding rule, such as your camera

name.

• Enter your camera’s IP address in the private/local IP field.

• Select

TCP

under

Traffic Type

.

• Enter the

HTTP port

your camera is set to use in the

Start

and

End

settings.

Note

: If you are using more than one camera, you will need to select a

different public port for each camera. If you cannot use port 80 for your

public port (for example, if you are already running a web server), select

a different public port for your camera.

• In the Port Forwarding list, a check mark appearing before the camera

name will indicate that the port forwarding rule is enabled.

• Click

Save Settings

to save your settings.

You will need to repeat these steps to open an RTSP port for your camera (port 554 by default).

48

D-Link DCS-1100/1130 User Manual

Appendix A - Installing the DCS-1100/1130 on a Router Without UPnP

Viewing Your Camera Over the Internet

After all settings have been entered correctly, a user inside or outside your network will have access to the camera

through a standard Web browser. To access your camera, simply type in the IP address of the router given to you by

your ISP, a colon, and the HTTP port number that you gave your camera.

http://<ip address>:<port>

To access your camera’s video streams directly, open your PC’s/device’s web browser or media player and type in

the IP address of the router given to you by your ISP, a colon, the RTSP port number that you gave your camera, then

the type of video stream you want to view as follows:

3GPP stream (mobile phone / pda): rtsp://<ip address>:<port>/3gpp

For example, if your camera’s IP is 192.168.0.35 and you set the RTSP port to 100,

rtsp://192.168.0.35:100/3gpp

To access your camera from a computer on your local (home) network, simply enter the local IP address of your

camera (i.e. 192.168.0.35). If using a port other than port 80, you must enter the IP address followed by a colon and

the assigned port number.

Note

: If your camera is connected to the Internet, you can also use the Camera IP given to you on the stickers inside

your box.

Viewing Your Camera Over the Internet Behind a Router

If you want to view one of your cameras over the Internet and your PC is behind a router or firewall, you may also need

to activate port triggering. This will allow you to open the necessary ports in order to view video from your camera.

Consult your router/firewall’s User Manual, and use the following information to set up port triggering:

•

Port trigger: 554 (if you have changed the RTSP port on your camera, use that number here)

•

Ports to open: 6970-6990

49

D-Link DCS-1100/1130 User Manual

Appendix B - Technical Specifications

Appendix B: Technical Specifications

System Requirements

• Operating System: Microsoft Windows 2000, XP, Vista

• Browser: Internet Explorer, Firefox, Opera

Networking Protocol

• IPv4, ARP, TCP, UDP, ICMP

• DHCP Client

• NTP Client

• DNS Client

• DDNS Client

• SMTP Client

• FTP Client

• HTTP Server

• Samba Client

• PPPoE

• RTP

• RTSP

• RTCP

• 3GPP

• UPnP Port Forwarding

LAN

• 10/100BASE-TX port

• IEEE 802.3 compliant

• IEEE 802.3u compliant

• Supports Full-Duplex operation

• MDI/MDIX auto-negotiation

• 802.3x Flow Control support for Full-Duplex mode

Wireless Connectivity

(DCS-1130 only)

• 802.11 n/g Wireless with WEP/WPA/WPA2 Security

• WPS Support

Sensor

• ¼ inch color VGA CMOS Sensor

Lens

• Focal length: 5.01mm, F2.8

Microphone

• Signal/noise ratio: 40dB +/- 3dB, Omni-directional

Reset Button

• Reset to factory default

Video Codec

• MPEG-4/MJPEG simultaneous dual-format compression

• JPEG for still image

Video Features

• Adjustable image size and quality

• Time stamp and text overlay

• Flip and Mirror

• Fully configurable motion detection window

Video Resolution

• VGA (640 x 480):

640 x 480 at 30fps

320 x 240 at 30fps

160 x 120 at 30fps

50

D-Link DCS-1100/1130 User Manual

Appendix B - Technical Specifications

Audio Codec

• GSM-AMR: 12.2Kbps

• PCM: 8Kbps

Light Sensitivity

• 1 [email protected]

Digital Zoom

• Up to 16X

3A Control

• AGC (Auto Gain Control)

• AWB ( Auto White Balance)

• AES (Auto Electronic Shutter)

Power

• Input: 100-240VAC, 50/60Hz

• Output: 5VDC, 2.5A

• Powered by an external power adapter

• Maximum power consumption

DCS-1100: 4W

DCS-1130: 6.3W

Dimensions (WxDxH)

• 120.0mm x 81.5mm x 38.0mm

(without bracket and stand)

Weight

• DCS-1100: 250g (without bracket and stand)

• DCS-1130: 280g (without bracket and stand)

Operation Temperature

• 0˚ to 40˚C (32˚ to 104˚F)

Storage Temperature

•- 20˚ to 70˚C (-4˚ to 158˚F)

Humidity

• 20-80% RH non-condensing

Emission (EMI), Safety & Other Certifications

• FCC Class B

• IC

• C-Tick

• CE