Page 61 / 100 Scroll up to view Page 56 - 60
61
D-Link DAP-1522 User Manual
Section 3 - Configuration
Transmit Power:
RTS Threshold:
Fragmentation
Threshold:
Short GI:
Set the transmit power of the antennas.
This value should remain at its default setting of
2436. If inconsistent data flow is a problem, only a
minor modification should be made.
The fragmentation threshold, which is specified
in bytes, determines whether packets will be
fragmented. Packets exceeding the 2346 byte
setting will be fragmented before transmission.
2346 is the default setting.
Check this box to reduce the guard interval time
therefore increasing the data capacity. However,
it is less reliable and may create higher data loss.
Advanced
Advanced Wireless
Page 62 / 100
62
D-Link DAP-1522 User Manual
Section 3 - Configuration
Enable QoS:
QoS Type:
Priority by LAN
Port:
Enable this option if you want QoS to prioritize
your traffic.
There are two options available for your special
application: (1) Priority by LAN Port, and (2) Priority
by Protocol.
There are four priority levels for all LAN ports. The
priority level values assigned are 1 for Background,
3 for Best Effort, 5 for Video, and 7 for Voice (Voice
is the highest level and Background is the lowest
level) at a normal priority.
QoS
The Quality of Service (QoS) feature regulates the flow of data through the access point by assigning a priority to
each packet.
It enhances your experience of wireless network usage by prioritizing the traffic of different applications.
Enabling this option allows the AP to prioritize traffic. There are two options available for the special application.
Page 63 / 100
63
D-Link DAP-1522 User Manual
Section 3 - Configuration
Priority by
Protocol:
Wireless to
Ethernet:
Ethernet to
Wireless:
ACK/DHCP/ICMP/
DNS Priority:
Web Traffic
Priority:
Mail Traffic
Priority:
Ftp Traffic Priority:
Other Traffic
Priority:
Users can set the priority and percentage of total bandwidth
reserved for each of their four traffic categories. Please
note that the combined percentage value of transmission
limits does not have to be 100%. These percentages
represent the maximum bandwidth designated for each
traffic category.
The value entered here indicates the wireless to Ethernet
speed required before the Advanced QoS function is
enabled. Advanced QoS will be enabled once the total
bandwidth reaches or surpasses the set value. The
suggested range is 800 ~ 96000kbits/sec.
The value entered here indicates the Ethernet to wireless
speed required before the Advanced QoS function is
enabled. Advanced QoS will be enabled once the total
bandwidth reaches or surpasses the set value. The
suggested range is 800 ~ 96000kbits/sec.
Represents the priority value and bandwidth limit applied to ACK, DHCP, ICMP, and DNS for packet delivering.
Traffic generated by typical Web services (packets sent through ports 80,443, 3128 and 8080).
Traffic generated by e-mail sending and receiving (ports 25, 110, 465 and 995).
Traffic generated by FTP Uploading and Downloading (ports 20, 21).
Other traffic generated that does not regard the aforementioned packet delivery.
Note:
Normally the wireless connection transmits application data packets based on the wireless to Ethernet speed and Ethernet to wireless speed.
Users can treat the two speeds as system transmission bandwidth, where all applications will share the whole system bandwidth based on assigned
priorities. Note that the maximum amount of bandwidth that can be used is the same as the set value of both speeds.
Page 64 / 100
64
D-Link DAP-1522 User Manual
Section 3 - Configuration
Enter a name for your new schedule.
Select a day, a range of days, or All Week to
include every day.
Check
All Days
or enter a start and end time for
your schedule.
Select
On
or
Off
from the drop-down menu.
Click
Add
to save your schedule. You must click
Save Settings
at the top for your schedules to
go into effect.
The list of schedules will be listed here. Click the
Edit
icon to make changes or click the
Delete
icon to remove the schedule.
Name:
Days:
Time:
Wireless:
Add:
Schedule Rules
List:
Schedule
Page 65 / 100
65
D-Link DAP-1522 User Manual
Section 3 - Configuration
Password:
Verify
Password:
Enter a new password for the Administrator Login
Name. The administrator can make changes to the
settings.
Enter the same password that you entered in the
previous textbox in order to confirm its accuracy.
Tools
Admin
This page will allow you to change the Administrator password. Admin has read/write access.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top