Page 76 / 98
Scroll up to view Page 71 - 75
76
D-Link DAP-1360 User Manual
Section 4 - Security
Configure WPA/WPA2 Personal
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1. Log into the web-based configuration by opening a web browser
and entering the IP address of the access point (192.168.0.50).
Click on Setup and then click Wireless Settings on the left side.
2. Next to
Security Mode
, select
Enable WPA Wireless Security
,
Enable WPA2 Wireless Security
, or
Enable WPA2-Auto
Wireless Security
.
3. Next to
Cipher Type
, select
TKIP
,
AES
, or
Auto
.
4. Next to
PSK / EAP
, select
Personal
.
5. Next to
Passphrase
, enter a key. The key is entered as a passphrase in ASCII format at both ends of the wireless
connection. The passphrase must be between 8-63 characters.
6. Click
Save Settings
at the top of the window to save your settings. If you are configuring the access point with a
wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase
as you did on the access point.
Page 77 / 98
77
D-Link DAP-1360 User Manual
Section 4 - Security
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1. Log into the web-based configuration by opening a web browser
and entering the IP address of the access point (192.168.0.50).
Click on
Setup
and then click
Wireless Settings
on the left
side.
2. Next to
Security Mode
, select
Enable WPA Wireless Security
,
Enable WPA2 Wireless Security
, or
Enable WPA2-Auto
Wireless Security
.
3. Next to
Cipher Mode
, select
TKIP
,
AES
, or
Auto
.
4. Next to
Personal / Enterprise
, select
Enterprise
.
5. Next to
RADIUS Server
, enter the IP Address of your RADIUS
server.
6. Next to
Port
, enter the port you are using with your RADIUS server. 1812 is the default port.
7. Next to
Shared Secret
, enter the security key.
8. Click
Save Settings
to save your settings.
Configure WPA/WPA2 Enterprise
Page 78 / 98
78
D-Link DAP-1360 User Manual
Section 5 - Connecting to a Wireless Network
Connect to a Wireless Network
Using Windows
®
XP
Windows
®
XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for
Service Pack 2 users.
If you are using another company’s utility or Windows
®
2000, please refer to the user manual
of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option
similar to the Windows
®
XP utility as seen below.
Right-click on the wireless computer icon in your system tray
(lower-right corner next to the time). Select
View Available
Wireless Networks
.
If you receive the
Wireless Networks Detected
bubble, click
on the center of the bubble to access the utility.
or
The utility will display any available wireless networks in your
area. Click on a network (displayed using the SSID) and click
the
Connect
button.
If you get a good signal, but cannot access the Internet, check
you TCP/IP settings for your wireless adapter. Refer to the
Networking Basics
section in this manual for more information.
Page 79 / 98
79
D-Link DAP-1360 User Manual
Section 5 - Connecting to a Wireless Network
Configure WEP
It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter.
If you are joining an existing network, you will need to know the WEP key being used.
2. Highlight the wireless network (SSID) you would like to
connect to and click
Connect.
1. Open the Windows
®
XP Wireless Utility by right-clicking
on the wireless computer icon in your system tray
(lower-right corner of screen). Select
View Available
Wireless Networks.
Page 80 / 98
80
D-Link DAP-1360 User Manual
Section 5 - Connecting to a Wireless Network
3. The
Wireless Network Connection
box will appear. Enter the
same WEP key that is on your access point and click
Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WEP settings are correct. The
WEP key must be exactly the same as on the wireless access point.
19216811.live