Page 51 / 178 Scroll up to view Page 46 - 50
will reboot with the default settings and the setup should complete at this point.
Information:
The Wireless Broadband Router is configured by default with the following settings:
The Cable/xDSL interface is configured with the DHCP client enabled.
The Local Area Network and Wireless interfaces are configured with the DHCP server enabled.
No user name, password, computer name, or workgroup name are enabled.
This configuration will work properly with a cable modem provider that does not require authentication.
Back to Top
xDSL with PPPoE
1. Connect the Ethernet port on the DSL modem to the
Internet
port on the router via an Ethernet cable.
2. Connect any one of the four
LAN
port on the router to the Ethernet port on your computer via another Ethernet cable.
(Connect to the router from your PC with a wireless network adapter.)
3. Power on the router.
4. Open your web browser and go to
http://my.router
, (or the default address
.)
5. Click the
Basic Settings
tab on the top navigation bar.
6. Click the
CABLE/xDSL ISP Settings
tab on the left navigation bar.
7. Check the
Your ISP requires you to input username/password (PPPoE Settings)
box.
8. Enter the user name provided to you by your ISP in the
User Name
box.
9. Enter your password in the
Password
and
Retype Password
boxes.
10. If your ISP requires you to provide a
MAC
address, check the
Your ISP requires you to input WAN Ethernet Mac
box.
11. Enter the address in the appropriate box.
12. Click the
Next
button.
13. Click the
Save & Restart
button.
14. Note the status bar at the bottom of the screen.
15. While the Wireless Broadband Router resets, the
Power
light on the front of the unit blinks.
16. When your web browser returns to the main page of the Wireless Broadband, the device has successfully restarted with
the new settings.
Back to Top
Back to Contents Page
Page 52 / 178
Back to Contents Page
Installing and Configuring the Router for non-Ethernet Cable
Connections
A cable modem may support only Ethernet connection, only USB connection, or both types of connections.
Cable modem with only USB Connection
Your TrueMobile 2300 router is designed to function with only Ethernet connection on its Broadband interface. If your cable
modem supports only USB connection, you need to replace it with a model with at least one Ethernet connection.
Cable modem with both USB and Ethernet Connections
If your cable modem supports both USB and Ethernet connections, but is connected to your computer via USB cable, follow
the instructions below to switch to the Ethernet connection.
1. Make sure that your cable modem is powered off.
2. Disconnect the USB cable from your computer and the cable modem.
3. Connect one end of an standard Ethernet cable into the Ethernet port of the Ethernet card on your computer
4. Insert the other end of the cable into the Ethernet port on your cable modem.
5. Turn on cable modem. The modem may need several minutes to initialize.
6. Insert the TrueMobile 2300 CD into the CDROM drive on the computer to start the Setup Wizard and select
"
Installation
" and "
Setup First Computer
" to begin the installation of the router.
Back to Top
Back to Contents Page
Page 53 / 178
Back to Contents Page
Configuring Your Router for the Existing Network
If you have an existing network, chances are you have already configured network services on the network. In this case, you
would use the router as a pure Access Point to extend the range of your network by allowing more attachment of wireless and
wired computers. You
MUST
also turn off the DHCP server on the router if there is a DHCP server running to avoid IP
address conflict.
To configure the router as an Access Point with the DHCP server disabled:
1. Open your web browser and go to
http://my.router
, (or the default address
.)
2. Click the
Basic Settings
tab on the top navigation bar.
3. Select
Access Point
Mode.
4. Click the
Next
button.
5. Click
OK
to dismiss the DHCP disabled message box (The DHCP server will be disabled in Access Point Mode by
default).
6. Click the
Advanced Settings
tab on the top navigation bar.
7. Click the
Advanced IP Settings
tab on the left navigation bar.
8. Assign an IP address to the Wireless Broadband Router.
NOTE: The IP address should be reserved by the DHCP server. The Wireless Broadband Router cannot act as a
DHCP client, therefore, it needs a static IP address for its LAN interface.
9. Click the
Submit
button.
10. Click the
Save & Restart
button.
Page 54 / 178
11. Note the status bar at the bottom of the screen.
12. While the Wireless Broadband Router resets, the
Power
light on the front of the unit blinks.
13. When your web browser returns to the main page of the Wireless Broadband Route, the device has successfully
restarted with the new settings.
NOTE:
The main page may not return if you have changed IP address of the router in Step 8. To view the main
page, type the new IP address of the router in the web browser to access it.
14. Plug an Ethernet cable from the existing local network into any
LAN
port on the Wireless Broadband Router.
Back to Contents Page
Page 55 / 178
Back to Contents Page
Configuring Your Dell™ TrueMobile™ 2300 Router for Gaming
This section will assist in configuring the Dell TrueMobile 2300 Router for gaming. In some cases, the firewall feature of the
router will cause a game not to function as intended. This document will not provide details for each game, but will discuss
how to open TCP/IP ports for one or more system.
WARNING:
Operating any client systems on the Internet without firewall protection may allow un-authorized access to a
system. This may lead to data loss.
Follow below steps to set up the router for gaming:
1. Select the system or systems to be used as game systems.
2. Locate the MAC address.
For Windows 2000 and XP
a. Click
Start
->
Run
.
b. Type
cmd
, and click
OK
.
c. On the command prompt, type
ipconfig /all
d. Write down the MAC (Physical) address of your computer to configure for gaming.
3. Open the web browser, and type
http://my.router
(or
)
4. Click the
Advanced Settings
tab.
5. Click the
DHCP Server Settings
tab on the left navigation bar.
6. Click
Add
button in
IP Address Reservation
,
a. Enter the MAC address of the system you wish to use for gaming in
MAC Address
field.
b. Enter an
IP address
for the system (select a number between 101 and 254)
7. Click
Submit
.
8. Click the
Port Forwarding Settings
tab on the left navigation bar.
a. To set a single computer for gaming, check the
Enable DMZ Host
box.
b. Enter the IP address of the system at
DMZ IP Address
field.
c. Click
Submit
.
NOTE: Only a single computer can be set for DMZ service. To set multiple computers for gaming, please
refer to the
Custom Port Forwarding Settings
under the
Port Forwarding Settings
.
9. Reboot the client system. The client system will use the newly assigned IP and will not have any TCP/IP ports blocked
by the firewall feature of the router.
Back to Contents Page

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top