Dell TrueMobile-2300 Router Manual PDF (Setup & Configuration Guide)

Page 46 / 178 Scroll up to view Page 41 - 45

Back to Contents Page

Web-based Configuration Tool:

Dell™ TrueMobile™ 2300 Wireless Broadband Router User's Guide

Overview

Basic Settings

Device Status

System Tools

Advanced Settings

Log Off

Overview

The web-based configuration tool enables you to set up every possible network configuration for your Dell TrueMobile 2300 Wireless Broadband

Router. Follow the instructions below to gain access to the web tool.

NOTE: Microsoft Internet Explorer (4.0 or higher) or Netscape (4.0 or higher) must be used for the web-based configuration tool.

1. On a Windows-based computer, Click

Start

and

Run

, and then type the following to bring up the configuration screen of the router:

http://my.router

(or the default address

http://192.168.2.1

.)

2. If this is the first time configuring your Wireless Broadband Router, or if the username and password have not been changed, type "admin"

both in the

User Name

and

Password

boxes, and then click

OK

.

3. After you have successfully opened the configuration screen as illustrated below, select a topic such

Basic Settings

and click the

corresponding tab on the top navigation bar to manage your router.

NOTE: Dell technical support representatives do not support the configuration options in the

Advanced Settings

portion of the

configuration program. These options are provided for your convenience only; however, the advanced settings are fully documented and

explained in this guide.

Page 47 / 178

Back to Top

Log Off

To prevent confusion when multiple people try to configure the Wireless Broadband Router simultaneously, the web-based configuration tool

allows one user at most to access the configuration screen of the router at any time. However, there is a five minute default timeout period after

the current administrator discontinues his usage of the web-based configuration tool, before the others are allowed to access the tool again.

To minimize the impact of the five minute timeout, click the

Log Off

tab to relinquish control of the web based configuration tool. This will allow

other legitimate users to access the tool.

Back to Top

Back to Contents Page

Page 48 / 178

Back to Contents Page

Cable Modem Connection

NOTE:

It's recommended that you install the router for Internet connectivity with the Setup Wizard provided on the TrueMobile 2300 CD.

Perform the below installation steps only when you are unable to install the router with the Setup Wizard for Internet connectivity.

Cable Modem - Standard Setup

Use this setup when your Cable service provider does not require you to enter any information for your Internet Broadband

connection.

Cable Modem with name settings

Use this setup when your Cable service provider requires you to enter

Host Name

and

Domain Name

for your Internet

Broadband connection.

Cable Modem with other settings

Use this setup when your Cable service provider requires you to enter other information.

Cable Modem - Standard Setup

1. Connect the Ethernet port on the Cable modem to the

Internet

port on the router via an Ethernet cable.

2. Connect any one of the four

LAN

port on the router to the Ethernet port on your computer via another Ethernet cable. (Connect to the

router from your PC with a wireless network adapter.)

3. Power on the router.

4. The setup should work on the router with factory default settings.

NOTE: If the installation is not successful because you have modified any setting or due to other factors, you can restore the

default settings by pushing the

Reset

button at the side of the router for at least 2 seconds. The router will reboot with the

default settings and the setup should complete at this point.

Information:

The Wireless Broadband Router is configured by default with the following settings:

The Cable/xDSL interface is configured with the DHCP client enabled.

The Local Area Network and Wireless interfaces are configured with the DHCP server enabled.

No user name, password, computer name, or workgroup name are enabled.

Page 49 / 178

This configuration will work properly with a cable modem provider that does not require authentication.

Back to Top

Cable Modem with name settings

1. Connect the Ethernet port on the Cable modem to the

Internet

port on the router via an Ethernet cable.

2. Connect any one of the four

LAN

port on the router to the Ethernet port on your computer via another Ethernet cable. (Connect to the

router from your PC with a wireless network adapter.)

3. Power on the router

4. Open your web browser and go to

http://my.router

, (or the default address

http://192.168.2.1

.)

5. Click the

Basic Settings

tab on the top navigation bar.

6. Click the

CABLE/xDSL ISP Settings

tab on the left navigation bar.

7. Check the

Your ISP requires you to input Host Computer Name or Domain Name

box.

8. Enter the Host Name and Computer Name assigned to you into the appropriate boxes.

9. Click the

10. Click the

Save & Restart

button to store the new settings.

11. Note the status bar at the bottom of the screen.

12. While the Wireless Broadband Router resets, the

Power

light on the front of the unit blinks.

13. When your web browser returns to the main page of the Wireless Broadband Route, the device has successfully restarted with the

new settings.

Back to Top

Cable Modem with other settings

If your Cable service provider requires you to enter other settings for your Internet Broadband connection, reference the steps in

Cable

Modem with name settings

to go to the

CABLE/xDSL ISP Settings

page and check only the appropriate field box and enter the required

values by your ISP.

Back to Top

Back to Contents Page

Page 50 / 178

Back to Contents Page

xDSL Modem Connection

NOTE: It's recommended that you install the router for Internet connectivity with the Setup Wizard provided on the

TrueMobile 2300 CD.

Perform the below installation steps only when you are unable to install the router with the Setup Wizard for Internet

connectivity.

xDSL without PPPoE - Standard Setup

Use this setup when your DSL service provider does not ask you to enter any information for your Internet

Broadband connection.

xDSL with PPPoE

Use this setup if your ISP has given you a username and password for your Internet Broadband connection.

xDSL without PPPoE - Standard Setup

1. Connect the Ethernet port on the DSL modem to the

Internet

port on the router via an Ethernet cable.

2. Connect any one of the four

LAN

port on the router to the Ethernet port on your computer via another Ethernet cable.

(Connect to the router from your PC with a wireless network adapter.)

3. Power on the router.

4. The setup should work on the router with factory default settings.

NOTE: If the installation is not successful because you have modified any setting or due to other factors, you can

restore the default settings by push the

Reset

button at the side of the router for at least 2 seconds. The router

Rate

Popular Dell Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share