Page 176 / 199 Scroll up to view Page 171 - 175
Configuring a Gateway-to-Gateway VPN Tunnel Between RV0xx Series Routers
Configuring a VPN Tunnel on a Cisco RV0xx Series Router
Cisco Small Business RV0xx Series Routers Administration Guide
176
D
-
If the remote gateway (Site B) has a dynamic IP address and a
Dynamic DNS hostname:
Select
Dynamic IP + Domain Name (FQDN)
Authentication
. Enter the registered
Domain Name
of the Site B router,
such as MyBusiness.DynDNS.org.
Remote Security Group Type—
Select
Subnet
. Enter the LAN
IP Address
and
Subnet Mask
of the Site B router.
STEP
6
In the
IPSec Setup
section, keep the default settings (recommended) or enter
other settings if desired. Ensure that you configure the Site B router with the same
settings.
STEP
7
In the
Preshared Key
field, enter a string for this key, for example, 13572468.
Ensure that you configure the other router with the same preshared key.
STEP
8
If you need more detailed settings, click
Advanced
. Otherwise, click
Save
.
Note:
Advanced settings can be used to enable features such as dead peer
detection, NAT traversal, split DNS, and NetBIOS broadcast messages.
STEP
9
At the remote site (Site B), set up the router with the corresponding settings
(where Site B is the “local gateway” and Site A is the “remote gateway:).
STEP 10
Use the
VPN > Summary
page to verify that the tunnel is active.
STEP 11
Verify that a computer at Site A can ping a computer at Site B, and vice versa.
(Refer to Windows Help for more information). If the ping test is successful, then
the VPN tunnel is configured correctly.
STEP 12
Repeat this procedure to configure additional VPN tunnel.
Example: Sites with Static WAN IP Addresses
Settings on the Site A Router:
Field
Value
Local Group Setup
Local Security
Gateway Type
IP Only
IP Address
(Automatically detected) 203.165.200.226
Local Security
Group Type
Subnet
Page 177 / 199
Configuring a Gateway-to-Gateway VPN Tunnel Between RV0xx Series Routers
Configuring a VPN Tunnel on a Cisco RV0xx Series Router
Cisco Small Business RV0xx Series Routers Administration Guide
177
D
IP Address
192.168.1.0
Subnet Mask
255.255.255.0
Remote Group Setup
Remote Security
Gateway Type
IP Only
IP Address
209.165.200.238
Remote Security
Group Type
Subnet
IP Address
192.168.2.0
Subnet Mask
255.255.255.0
IPSec Setup
Keying Mode
IKE with Preshared Key
Phase 1
Encryption
DES
Phase 1
Authentication
MD5
Phase 1 SA Life
Time
28800
Perfect Forward
Secrecy
Enabled
Phase 2 DH
Group
Group 1 - 768 bit
Phase 2
Encryption
DES
Phase 2
Authentication
MD5
Phase 2 SA Life
Time
3600
Preshared Key
13572468#123456789
Field
Value
Page 178 / 199
Configuring a Gateway-to-Gateway VPN Tunnel Between RV0xx Series Routers
Configuring a VPN Tunnel on a Cisco RV0xx Series Router
Cisco Small Business RV0xx Series Routers Administration Guide
178
D
Settings on the Site B Router:
Minimum
Preshared Key
Complexity
Enabled
Advanced
Default settings
Field
Values
Local Group Setup
Local Security
Gateway Type
IP Only
IP Address
(Automatically detected) 209.165.200.238
Local Security
Group Type
Subnet
IP Address
192.168.2.0
Subnet Mask
255.255.255.0
Remote Group Setup
Remote Security
Gateway Type
IP Only
IP Address
203.165.200.226
Remote Security
Group Type
Subnet
IP Address
192.168.1.0
Subnet Mask
255.255.255.0
IPSec Setup
Keying Mode
IKE with Preshared Key
Phase 1
Encryption
DES
Field
Value
Page 179 / 199
Configuring a Gateway-to-Gateway VPN Tunnel Between RV0xx Series Routers
Configuring a VPN Tunnel on a Cisco RV0xx Series Router
Cisco Small Business RV0xx Series Routers Administration Guide
179
D
Example: Site with a Dynamic WAN IP Address
Settings on the Site A Router:
Phase 1
Authentication
MD5
Phase 1 SA Life
Time
28800
Perfect Forward
Secrecy
Enabled
Phase 2 DH
Group
Group 1 - 768 bit
Phase 2
Encryption
DES
Phase 2
Authentication
MD5
Phase 2 SA Life
Time
3600
Preshared Key
13572468#123456789
Minimum
Preshared Key
Complexity
Enabled
Advanced
Default settings
Field
Value
Local Group Setup
Local Security
Gateway Type
IP Only
IP Address
(Automatically detected) 203.165.200.226
Field
Values
Page 180 / 199
Configuring a Gateway-to-Gateway VPN Tunnel Between RV0xx Series Routers
Configuring a VPN Tunnel on a Cisco RV0xx Series Router
Cisco Small Business RV0xx Series Routers Administration Guide
180
D
Local Security
Group Type
Subnet
IP Address
192.168.1.0
Subnet Mask
255.255.255.0
Remote Group Setup
Remote Security
Gateway Type
Dynamic IP + Domain Name (FQDN) Authentication
Domain Name
cisco.com
Remote Security
Group Type
Subnet
IP Address
192.168.2.0
Subnet Mask
255.255.255.0
IPSec Setup
Keying Mode
IKE with Preshared Key
Phase 1
Encryption
DES
Phase 1
Authentication
MD5
Phase 1 SA Life
Time
28800
Perfect Forward
Secrecy
Enabled
Phase 2 DH
Group
Group 1 - 768 bit
Phase 2
Encryption
DES
Phase 2
Authentication
MD5
Field
Value

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top