1. Home
    2. /
  2. Manuals
    3. /
  3. Buffalo
    4. /
  4. WCR-GN
    5. /
  5. 5
Page 21 / 109 Scroll up to view Page 16 - 20
WCR-GN User Manual
20
Chapter 3
Installation
Manual Setup
To configure the WDS without using the utility CD, follow the procedure below.
1
Fix your computer’s IP address. For details, please refer to Appnedix C (page 96).
ex) IP address
192.168.11.80
Subnet mask
255.255.255.0
Default gateway
blank
Preferred DNS server
blank
Alternate DNS server
blank
2
Turn off your computer.
3
Connect your computer to one of the AirStation’s LAN ports with the Ethenet cable.
Turn on the AirStation, wait one minute, and then turn on your computer.
power outlet
AirStation wireless router
(rear side)
PC
1) connect
1) connect
Ethernet cable
2) connect the power supply
4
Wait for a while, and then make sure that the AirStation’s LEDs are lit as described below:
POWER
Green light is on
WIRELESS
Green light is on
ROUTER
Green light is on
DIAG
Off
※
Refer to page 8 and 10 for LED locations and other details.
Page 22 / 109
Chapter 3
Installation
WCR-GN User Manual
21
5
Open the web configuration screen. Refer to page 23 for the instruction as necessary.
6
In the "
Mode information
" menu, select
"Bridge Mode"
and click "
Apply
".
7
When this below screen appears, re-enter
the user name "
root
" and password set up
for web configuration screen. Click "
OK
".
8
Web configuration screen will open again. Click "
Wireless Config
" , then "
WDS
".
9
Check "
Use
" option and select "
Manual
" from the "
Connection type
".
Click "
Search
"
Page 23 / 109
WCR-GN User Manual
22
Chapter 3
Installation
10
A list of available wireless APs will be generated. Select the target AP and click "
Select
".
Click "
Search again
" if no APs are found.
11
Configure the security information of the target AP and click "
Apply
".
12
Revert to the original IP adress setting. Refer to Appendix C (page 96) again.
ex) IP address
obtain an IP address automatically
Subnet mask
obtain DNS server address automatically
You’ve completed the WDS setup. Refer to Chapter 4 for advanced settings.
Page 24 / 109
WCR-GN User Manual
23
Chapter 4
Configuration
This chapter explains the advanced settings for the AirStation. To change advanced settings, use the
AirStation's web-based configuration utility.
How to Access the Web-Based Configuration Utility
To display the configuration of the AirStation, follow the procedure below.
1
2
3
Launch a web browser.
Enter the router’s LAN-side IP address in the address
field, and press the "Enter" key.
Note:
･
The AirStation’s default LAN-side IP address depends on its mode setting.
In router mode: 192.168.11.1
In bridge mode: 192.168.11.100
･
If you change the IP address of this unit, use the new IP address.
When this screen appears, enter“
root”
(in lower case) for the user name and the
password that you set during initial setup.
Click“
OK”
.
Note:
･
By default, the password is blank (not set).
･
If you forget your password, hold down
the Reset button (page 11) to initialize all
settings. The password will then be blank.
Note that all other settings will also revert to
their default values.
Page 25 / 109
WCR-GN User Manual
24
Chapter 4
Configuration
4
The configuration screen is
displayed.
Help is always displayed on the
right side of the configuration
screen. Refer to the Help screens
for more information on each page
in the web-based configuration
screens.

Rate

3.5 / 5 based on 2 votes.

Popular Buffalo Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top