1. Home
    2. /
  2. Manuals
    3. /
  3. Billion
    4. /
  4. BiPAC 7800DXL
    5. /
  5. 25
Page 121 / 211 Scroll up to view Page 116 - 120
117
WAN IP Address:
Enter your IPv4 address to the device provided by your ISP.
WAN Subnet Mask:
Enter your submask to the device provided by your ISP.
WAN gateway IP Address:
Enter your gateway IP address to the device provided by your ISP.
IPv6 for this service:
Enable to use IPv6 service.
Obtain an IPv6 address automatically:
check whether to enable or disable this feature.
WAN IPv6 Address/Prefix Length:
Enter the WAN IPv6 Address/Prefix Length from your ISP.
WAN Next-Hop IPv6 Address:
Enter the WAN Next-Hop IPv6 Address from your ISP.
Note:
If you don’t know well about the DHCP Option, you can leave it empty or leave it as default.
NAT:
The NAT (Network Address Translation) feature allows multiple users to access the Internet
through a single IP account by sharing the single IP address. If users on your LAN have their own
public IP addresses to access the Internet, NAT function can be disabled. When enabled, a Fullcone
NAT parameter will appear, you can determine whether to enable Fullcone NAT. While only NAT
enabled, the default NAT type Port-Restricted cone NAT will be used.
Fullcone NAT:
Enable or disable fullcone NAT. Fullcone is a kind of NAT, in this mode, all requests
from the same internal IP address and port are mapped to the same external IP address and port.
Furthermore, any external host can send a packet to the internal host, by sending a packet to the
mapped external address.
Firewall:
Enable to drop all traffic from WAN side. If enabled, all incoming packets by default would
be dropped, and please turn to
IP Filtering Incoming
to add allowing rules.
IGMP Multicast:
IGMP (
Internet Group Membership
Protocol) is a protocol used by IP hosts to
report their multicast group memberships to any immediately neighboring multicast routers. Check
this item to enable IGMP multicast on that WAN interface for multicast forwarding.
MLD Multicast Proxy:
check whether to enable this function. MLD (
Multicast Listener Discovery
Protocol) Proxy intercepts the MLD request from Clients a set up the multicast-forwarding table.
it
takes over some of the router’s job, simplifying the router’s job and multicast communication.
Support MLDv1 and MLDv2.
Page 122 / 211
118
Bridging
Description:
User-defined description for the connection, commonly for friendly use.
802.1P Priority:
The parameter indicates the frame priority level from 0 (lowest) to 7 (highest), which
can be used to prioritize different classes of traffic (voice, video, data, etc). Enter the priority
identification, tagged: 0-1, untagged: -1.
802.1Q VLAN ID:
It is a parameter to specify the VLAN which the frame belongs. Enter the VLAN ID
identification, tagged: 0-4094, untagged : -1.
Page 123 / 211
119
3G/LTE
Select 3G/LTE to configure the route to enjoy the mobility. By default the 3G/LTE interface is on,
user can edit the parameters to meet your own requirements.
Click
Edit
button to enter the 3G/LTE configuration page.
Failover:
If enabled, the 3G/LTE will work in failover mode and be brought up only when there is no
active default route. In this mode, 3G/LTE work as a backup for the WAN connectivity. While if
disabled, 3G/LTE serves as a normal interface, and can only be brought up when it has been
configured to achieve a mobile connectivity.
Mode:
There are 6 options of phone service standards: GSM 2G only, UTMS 3G only, GSM 2G
preferred, UMTS 3G preferred, Automatic, and Use 3G/LTE 3g dongle settings. If you are uncertain
what services are available to you, and then please select Automatic.
TEL No.:
The dial string to make a 3G/LTE user internetworking call. It may provide by your mobile
Page 124 / 211
120
service provider.
APN:
An APN is similar to a URL on the WWW, it is what the unit makes a GPRS / UMTS call. The
service provider is able to attach anything to an APN to create a data connection, requirements for
APNs varies between different service providers. Most service providers have an internet portal
which they use to connect to a DHCP Server, thus giving you access to the internet i.e. some 3G
operators use the APN ‘internet’ for their portal. The default value is “internet”.
Username
/
Password:
Enter the username and password provided by your service provider. The
username and password are case sensitive.
Authentication Protocol:
Default is Auto. Please consult your service provider on whether to use
PAP, CHAP or MSCHAP.
PIN:
PIN stands for Personal Identification Number. A PIN code is a numeric value used in certain
systems as a password to gain access, and authenticate. In mobile phones a PIN code locks the
SIM card until you enter the correct code. If you enter the PIN code incorrectly into the phone 3 times
in a row, then the SIM card will be blocked and you will require a PUK code from your network/
service provider.
Connect on Demand:
If you want to make UMTS/GPRS call only when there is a packet
requesting access to the Internet (i.e. when a program on your computer attempts to access
the Internet). In this mode, you must set Idle Timeout value at same time. Click on Connect on
Demand, the Idle Timeout field will display.
Idle Timeout:
Auto-disconnect the broadband firewall gateway when there is no activity on
the line for a predetermined period of time. Default is 600 seconds.
Keep Alive:
Check Enable to allow the router to send message out every 7 seconds (can be
changed base on need) to prevent the connection being dropped by ISP.
IP Address:
The IP address is used to “ping”, and router will ping the IP to find whether the
connection is still on.
NAT:
Check to enable the NAT function.
Firewall:
Enable to drop all traffic from WAN side. If enabled, all incoming packets by default would
be dropped, and please turn to
IP Filtering Incoming
to add allowing rules.
MTU:
MTU (Maximum Transmission Unit) is the size of the largest datagram that IP will attempt to
send through the interface.
Select default gateway interfaces:
Select from the interfaces the default gateway, here commonly
we select ppp3g0.
Selected DNS Server Interfaces:
Select the IP addresses of the DNS servers.
Click
Apply
to confirm the settings.
Page 125 / 211
121
Here you can configure WAN Service, if it is OK, you can access the internet. You can go to
Status
>WAN
or
Summary
to view the WAN connection information (Here user can see the 3G/LTE
failover).

Rate

4 / 5 based on 3 votes.

Popular Billion Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top