Page 16 / 130
Scroll up to view Page 11 - 15
Billion 810VGTX Router
Page | 15
Configuring PC in Windows NT4.0
1.
Go to Start / Settings / Control Panel. In the
Control Panel,
double-click Network and choose the Protocols tab
2.
Select TCP/IP Protocol and click Properties.
3.
Select the Obtain an IP address from a DHCP server radio button
and click OK.
Page 17 / 130
Billion 810VGTX Router
Page | 16
°
If you ever forget the login password, please press and hold the reset
button for longer than 6 seconds to restore the factory default settings.
Factory Default Settings
Before configuring your router, you need to know the following default settings.
Web Interface (Username and Password)
Username: admin
Password: admin
A
Attention
The default username and password are “
admin
” and “
admin
” respectively.
Device LAN IP settings
Subnet Mask: 255.255.255.0
ISP setting in WAN site
PPPoE
DHCP server
DHCP server is enabled.
Start IP Address: 10.0.0.100
IP pool counts: 100
LAN and WAN Port Addresses
The parameters of LAN and WAN ports are pre-set in the factory.
The default values are shown in the tale.
LAN Port
WAN Port
IP address
The PPPoE function is
enabled
to
automatically get the WAN port
configuration from the ISP, but you
have to set the username and
password first.
Subnet Mask
255.255.255.0
DHCP server function
Enabled
IP addresses for distribution
to PCs
100 IP addresses continuing from
10.0.0.100 through 10.0.0.199
Page 18 / 130
Billion 810VGTX Router
Page | 17
Information from your ISP
Telkom ADSL connections use PPPoE, and automatically assign a WAN IP address to your router. The following
information is provided should you wish to connect to an alternative ISP.
Gather the information as illustrated in the following table and keep it for reference.
PPPoE
VPI/VCI,
VC
/
LLC-based
multiplexing,
Username,
Password,
Service
Name,
and
Domain
Name
System
(DNS)
IP
address
(this
is
automatically
set
by
the
Telkom
network
but
be
set
manually
should
this
be
required).
PPPoE
(Multisession)
VPI/VCI,
VC
/
LLC-based
multiplexing,
Username,
Password,
Service
Name,
Domain
Name
System
(DNS)
IP
address and multiple-sessions on the same
PVC.
PPPoE
/
PPPoE
with
Pass-through
VPI/VCI,
VC
/
LLC-based
multiplexing,
Username,
Password,
Service
Name,
and
Domain
Name
System
(DNS)
IP
address
(this
is
automatically
set
by
the
Telkom
network
but
be
set
manually
should
this
be
required).
In
addition,
additional
WAN
address
can
be
assigned
using
PPPoE
dialler.
PPPoA
VPI/VCI,
VC
/
LLC-based
multiplexing,
Username,
Password
and
Domain
Name
System
(DNS)
IP
address
(it
can
be
automatically
assigned
by
your
ISP when
you
connect
or
be
set
manually).
RFC
1483
Bridged
VPI/VCI,
VC
/
LLC-based
multiplexing
to
use
Bridged
Mode.
RFC
1483
Routed
VPI/VCI,
VC
/
LLC-based
multiplexing,
IP
address,
Subnet
mask,
Gateway
address,
and
Domain
Name
System
(DNS)
IP
address
(it
is
a
fixed
IP
address).
IPoA
Routed
(IP
over
ATM)
VPI/VCI,
VC
/
LLC-based
multiplexing,
IP
address,
Subnet
mask,
Gateway
address,
and
Domain
Name
System
(DNS)
IP
address
(it
is
a
fixed
IP
address).
Configuring with your Web Browser
Open your web browser, enter the IP address of your router, which by default is
10.0.0.2, and click “Go”, a user
name and password window prompt will appear. The default username and password are “admin” and “admin”
respectively. (See Figure below)
Figure: User name & Password Prompt Window
Congratulations! You are now successfully logged onto your Router!
Page 19 / 130
Billion 810VGTX Router
Page | 18
CHAPTER4: CONFIGURATION
At the configuration homepage, the left navigation column provides you the link to each configuration page. The category
of each configuration page is listed as below.
Status
ADSL Table
3G Status
ARP Table
DHCP Table
Routing Table
NAT Sessions
UpnP Portmap
PPTP Status
IPSec Status
L2TP Status
Email Status
VoIP Status
VoIP Call Log
Event Log
Error Log
Diagnostic
Quick Start
Configuration
LAN
WAN
System
Firewall
VPN
VoIP
QoS
Virtual Server
Time Schedule
Advanced
Page 20 / 130
Billion 810VGTX Router
Page | 19
Status
ADSL Status
This section displays the overall status of ADSL, such as DSP firmware version, Operational mode,
Upstream/downstream rate, SNR margin, Line Attenuation, CRC Errors and Latency rate.
3G Status
This section displays the 3G Card overall status with information such as the current signal strength, statistics of current
data transmission and total data transmission.
19216811.live