1. Home
    2. /
  2. Manuals
    3. /
  3. Belkin
    4. /
  4. FSD7230-4
    5. /
  5. 8
Page 36 / 112 Scroll up to view Page 31 - 35
34
Alternate Setup Method
Setting your Internet Service Provider (ISP) Connection Type to
Point-to-Point Tunneling Protocol (PPTP)
[European Countries Only]. Some ISPs require a connection using
PPTP protocol, a type of connection most common in European
countries. This sets up a direct connection to the ISP’s system. Type
in the information provided by your ISP in the space provided. When
you have finished, click “Apply Changes”
(9)
. After you apply the
changes, the “Internet Status” indicator will read “connection OK” if
your Router is set up properly.
1.
User ID
Provided by your ISP. Enter your PPTP User ID here.
2.
Password
Type in your password and retype it into the “Retype Password”
box to confirm it.
3.
PPTP Gateway
Provided by your ISP. Enter your PPTP Gateway/service IP
address here.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Page 37 / 112
Alternate Setup Method
35
section
2
1
3
4
5
6
7
8
9
10
4.
Idle Time Out
The “Idle Time Out” feature is used to automatically disconnect
the Router from your ISP when there is no activity for a specified
period of time. For instance, placing a check mark next to this
option and entering “5” into the minute field will cause the Router
to disconnect from the Internet after five minutes of no Internet
activity. This option should be used if you pay for your Internet
service by the minute.
5.
My IP Address
Provided by your ISP. Enter the IP address here.
6
My Subnet Mask
Provided by your ISP. Enter the IP address here.
7.
Default Gateway
Provided by your ISP. Enter your Default Gateway here.
Page 38 / 112
36
Alternate Setup Method
Setting your Connection Type if you are a Telstra
®
BigPond User
[Australia Only]. Your user name and password are provided to you
by Telstra BigPond. Enter this information below. Choosing your state
from the drop-down menu
(6)
will automatically fill in your login server
IP address. If your login server address is different than the one
provided here, you may manually enter the login server IP address by
placing a check in the box next to “User decide login server manually”
(4)
and type in the address next to “Login Server”
(5)
. When you
have entered all of your information, click “Apply Changes”
(7)
.
After you apply the changes, the “Internet Status” indicator will read
“connection OK” if your Router is set up properly.
1.
Select your State
Select your state from the drop-down menu
(6)
. The “Login
Server” box will automatically be filled in with an IP address.
If for some reason this address does not match the address
that Telstra has given, you can manually enter the login server
address. See “User decide login server manually”
(4)
.
2.
User Name
Provided by your ISP. Type in your user name here.
(1)
(2)
(3)
(4)
(5)
Page 39 / 112
Alternate Setup Method
37
section
2
1
3
4
5
6
7
8
9
10
3.
Password
Type in your password and retype it into the “Retype Password”
box to confirm it.
4.
User Decide Login Server Manually
If your login server IP address is not available in the “Select Your
State” drop-down menu
(6)
, you may manually enter the login
server IP address by placing a check in the box next to “User
decide login server manually” and typing in the address next to
“Login Server”
(5)
.
Setting Custom Domain Name Server (DNS) Settings
A “Domain Name Server” is a server located on the Internet that
translates Universal Resource Locators (URLs) like “www.belkin.com”
into IP addresses. Many Internet Service Providers (ISPs) do not require
you to enter this information into the Router. The “Automatic from ISP”
box
(1)
should be checked if your ISP did not give you a specific DNS
address. If you are using a static IP connection type, then you may
need to enter a specific DNS address and secondary DNS address for
your connection to work properly. If your connection type is dynamic
or PPPoE, it is likely that you do not have to enter a DNS address.
Leave the “Automatic from ISP” box checked. To enter the DNS address
settings, uncheck the “Automatic from ISP” box and enter your DNS
entries in the spaces provided. Click “Apply Changes”
(2)
to save
the settings.
(1)
Page 40 / 112
38
Alternate Setup Method
Configuring your WAN Media Access Controller (MAC) Address
All network components including cards, adapters, and routers, have
a unique “serial number” called a MAC address. Your Internet Service
Provider may record the MAC address of your computer’s adapter and
only let that particular computer connect to the Internet service. When
you install the Router, its own MAC address will be “seen” by the
ISP and may cause the connection not to work. Belkin has provided
the ability to clone (copy) the MAC address of the computer into the
Router. This MAC address, in turn, will be seen by the ISP’s system as
the original MAC address and will allow the connection to work. If you
are not sure whether your ISP needs to see the original MAC address,
simply clone the MAC address of the computer that was originally
connected to the modem. Cloning the address will not cause any
problems with your network.

Rate

4.5 / 5 based on 2 votes.

Popular Belkin Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top