N Wireless Modem Router

SECTIONS

Table of Contents

1

2

3

4

6

7

8

9

10

5

ALTERNATE SETUP METHOD

For Static IP connection:

1° IP assigned by ISP –

Select “No” if your ISP instructed you to use

fixed IP°

2° IP Address –

Enter an IP address assigned by your ISP for the Router

WAN interface°

3° Subnet Mask –

Enter a subnet mask assigned by your ISP°

4° Default Gateway –

Enter a default gateway IP address assigned by

your ISP°

5° VPI/VCI –

Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameters here° These identifiers are assigned by

your ISP°

6° Encapsulation –

Select the LLC or VC MUX your ISP uses°

Click “Apply Changes” to save and activate your settings° To go back to

the original settings before saving, click “Clear Changes”° Or click any of

the Quick-Navigation links for other options° Your new settings will not

be saved unless your click “Apply Changes”°

For Dynamic IP connection:

1° IP assigned by ISP –

Select “Yes” if your ISP instructed you to use

Dynamic IP°

2° VPI/VCI –

Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameter here° These identifiers are assigned by

your ISP°

3° Encapsulation –

Select LLC or VC MUX your ISP uses°

Click “Apply Changes” to save and activate your settings° To go back

to the original settings before saving, click “Clear Changes”; or click

any of the Quick-Navigation links for other options° Your new settings

will not be saved unless you click “Apply Changes”°

N Wireless Modem Router

SECTIONS

Table of Contents

1

2

3

4

6

7

8

9

10

5

ALTERNATE SETUP METHOD

1° WAN IP Address –

Enter an IP address assigned by your ISP for the

Router WAN interface°

2° Subnet Mask –

Enter a subnet mask assigned by your ISP°

3° Use Static Default Gateway –

Enter a default gateway IP address°

If the Router cannot find the destination address within its local

network, it will forward the packets to the default gateway assigned

by your ISP°

4° VPI/VCI –

Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameter here° These identifiers are assigned by

your ISP°

5° Encapsulation –

Select LLC or VC MUX your ISP uses°

Click “Apply Changes” to save and activate your settings° To go back

to the original settings before saving, click “Clear Changes”° Or click

any of the Quick-Navigation links for other options° Your new settings

will not be saved unless your click “Apply Changes”°

Setting your ISP Connection Type to Static IP (IPoA)

This connection type is also called “Classical IP over ATM” or “CLIP”, which your ISP provides a fixed IP for your Router to connect to the Internet°

N Wireless Modem Router

SECTIONS

Table of Contents

1

2

3

4

6

7

8

9

10

5

ALTERNATE SETUP METHOD

1° Enable Bridge Service –

Check this box to enable bridge service

2° VPI/VCI –

Enter your Virtual Path Identifier (VPI) and Virtual Circuit

Identifier (VCI) parameters here° (Assigned by your ISP)°

3° Encapsulation –

Select the LLC or VC MUX your ISP uses°

Click “Apply Changes” to save and activate your settings° To go back to

the original settings before saving, click “Clear Changes”° Or click any of

the Quick-Navigation links for other options° Your new settings will not

be saved unless your click “Apply Changes”°

Setting your Connection Type to Modem Only (Disable Internet Sharing)

In this mode, the Router simply acts as a bridge passing packets across the DSL port° It requires additional software to be installed on your

computers in order to access the Internet°

N Wireless Modem Router

SECTIONS

Table of Contents

1

2

3

4

6

7

8

9

10

5

ALTERNATE SETUP METHOD

Setting Custom Domain Name Server (DNS) Settings

A “Domain Name Server” is a server located on the Internet that

translates Universal Resource Locaters (URLs) like “ belkin°com” to

IP addresses° Many Internet Service Providers (ISPs) do not require

you to enter this information into the Router° The “Automatic from

ISP” box

(1)

should be checked if your ISP did not give you a specific

DNS address° If you are using a static IP connection type, then you

may need to enter a specific DNS address and secondary DNS

address for your connection to work properly° If your connection

type is dynamic or PPPoE, it is likely that you do not have to enter

a DNS address° Leave the “Automatic from ISP” box checked° To

enter the DNS address settings, uncheck the “Automatic from ISP”

box and enter your DNS entries in the spaces provided° Click “Apply

Changes”

(2)

to save the settings

(1)

(2)

N Wireless Modem Router

SECTIONS

Table of Contents

1

2

3

4

5

7

8

9

10

USING THE WEB-BASED ADVANCED USER INTERFACE

6

Viewing the LAN Settings

Clicking on the header of the LAN tab

(1)

will take you to the LAN tab’s

header page° A quick description of the functions can be found here° To

view the settings or make changes to any of the LAN settings, click on

“LAN Settings”

(2)

or to view the list of connected computers, click on

“DHCP client list”

(3)

°

(2)

(1)

(3)

Using your Internet browser, you can access the Router’s Web-Based

Advanced User Interface° In your browser, type “192°168°2°1” (do

not type in anything else such as “http://” or “www”) then press the

“Enter” key°

You will see the Router’s home page in your browser window°