1. Home
    2. /
  2. Manuals
    3. /
  3. Belkin
    4. /
  4. F5D8630-4Av1
    5. /
  5. 3
Page 11 / 92 Scroll up to view Page 6 - 10
9
section
2
1
3
4
5
6
7
8
9
10
11
12
Note:
One RJ11 telephone cord is supplied. When inserting an
RJ11 plug, be sure the tab on the plug clicks into position to
ensure that it is properly seated.
3.
If you have a dedicated ADSL service telephone line with an RJ11
wall jack, simply connect a telephone cord from the wall jack to
the
gray
RJ11 port labeled “DSL line” on the back of
your Router.
4.
If you have an RJ45 wall jack for your ADSL service, connect an
RJ45-to-RJ11 converter to the wall jack. Then connect one end of
a telephone cord to the converter and the other end to the
gray
RJ11 port labeled “DSL line” on the back of your Router.
Note:
ADSL microfilter may or may not be provided depending on
your country.
Connecting your Router
Page 12 / 92
10
Powering Up your Router
1.
Connect the supplied power adapter to the Router power-input
plug labeled “Power”.
Note:
For safety and performance reasons, only use the supplied
power adapter to prevent damage to the Router.
2.
After connecting the power adapter and the power source is turned on,
the Router’s power icon
on the front panel should be on. It might
take a few minutes for the Router to fully start up.
3.
Turn on your computers. After your computers boot up, the LAN
status LED
on the front of the Router will be on for each port
to which a wired computer is connected. These lights show
you the connection and activity status. Now you are ready to
configure the Router for ADSL connection.
Connecting your Router
Page 13 / 92
Setting Up your Computers
11
section
2
1
3
4
5
6
7
8
9
10
11
12
In order for your computer to properly communicate with your Router, you
will need to change your computer’s “TCP/IP Ethernet” settings to “Obtain
an IP address automatically/Using DHCP”. This is normally the default
setting in most home computers.
You can set up the computer that is connected to the ADSL modem FIRST
using these steps. You can also use these steps to add computers to your
Router after the Router has been set up to connect to the Internet.
Manually Configuring Network Adapters in Windows XP, 2000, or NT
1.
Click “Start”, “Settings”, then “Control Panel”.
2.
Double-click on the “Network and dial-up connections” icon
(Windows 2000) or the “Network” icon (Windows XP).
3.
Right-click on the “Local Area Connection” associated with your
network adapter and select “Properties” from the drop-down menu.
4.
In the “Local Area Connection Properties” window, click “Internet
Protocol (TCP/IP)” and click the “Properties” button. The following
screen will appear:
5.
If “Use the following IP address”
(2)
is selected, your Router will need to
be set up for a static IP connection type. Write the address information
the table below. You will need to enter this information into the Router.
6.
If not already selected, select “Obtain an IP address automatically”
(1)
and “Obtain DNS server address automatically”
(3)
. Click “OK”.
Your network adapter(s) are now configured for use with the Router.
(1)
(2)
(3)
Page 14 / 92
12
Setting Up your Computers
Manually Configuring Network Adapters in Windows 98SE or Me
1.
Right-click on “My Network Neighborhood” and select “Properties” from
the drop-down menu.
2.
Select “TCP/IP -> settings” for your installed network adapter. You will
see the following window.
3.
If “Specify an IP address” is selected, your Router will need to be set up
for a static IP connection type. Write the address information in the table
below. You will need to enter this information into the Router.
(1)
(2)
(3)
4.
Write the IP address and subnet mask from the “IP Address” tab
(3)
.
5.
Click the “Gateway” tab
(2)
. Write the gateway address down in the chart.
6.
Click the “DNS Configuration” tab
(1)
. Write the DNS address(es) in the chart.
7.
If not already selected, select “Obtain an IP address automatically” on the
IP address tab. Click “OK”.
8.
You will also need to delete the Gateway address from the Gateway tab
and DNS Configuration entries in order to properly be configured for
connection to the Belkin router.
Restart the computer. When the computer restarts, your network
adapter(s) are now configured for use with the Router.
Page 15 / 92
Setting Up your Computers
13
section
2
1
3
4
5
6
7
8
9
10
11
12
Set up the computer that is connected to the cable or DSL modem
by FIRST using these steps. You can also use these steps to add
computers to your Router after the Router has been set up to connect
to the Internet.
Manually Configuring Network Adapters in Mac OS
up to 9.x
In order for your computer to properly communicate with your Router,
you will need to change your Mac computer’s TCP/IP settings to DHCP.
1.
Pull down the Apple menu. Select “Control Panels” and
select “TCP/IP”.
2.
You will see the TCP/IP control panel. Select “Ethernet Built-In”
or “Ethernet” in the “Connect via:” drop-down menu
(1)
.
3.
Next to “Configure”
(2)
, if “Manually” is selected, your Router
will need to be set up for a static IP connection type. Write the
address information in the table below. You will need to enter this
information into the Router.
(1)
(2)

Rate

124.8 / 5 based on 304 votes.

Popular Belkin Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top