1. Home
    2. /
  2. Manuals
    3. /
  3. Belkin
    4. /
  4. F5D8630-4Av1
    5. /
  5. 2
Page 6 / 92 Scroll up to view Page 1 - 5
4
Knowing your Router
3.
WLAN Status LED
The WLAN Status LED is solid GREEN when you enable the
wireless LAN function. It flashes when the Router is transmitting
or receiving data wirelessly.
OFF
WLAN is off
Green
WLAN is up and connected
Green - blinking
When transmitted or receiving data
4.
ADSL LED
The ADSL LED flashes GREEN during negotiation with your ISP.
It stays GREEN when the Router is connected properly to your
ADSL service.
OFF
no ADSL connection
Green
ADSL link is up and connected
Green - blinking
negotiating connection
5.
Internet LED
The Internet LED shows you when the Router is connected to
the Internet. When the LED is OFF, the Router is NOT connected
to the Internet. When the LED is solid GREEN, the Router is
connected to the Internet. When the LED is blinking, the Router
is transmitting or receiving data from the Internet.
OFF
No Internet connection
Green
Connected to the Internet
Green - blinking
When transmitting or receiving data
Red
Failed to get IP
Page 7 / 92
Knowing your Router
5
section
2
1
3
4
5
6
7
8
9
10
11
12
Back Panel
6.
DSL Line
This port is for connection to your ADSL line. Connect your ADSL
line to this port.
7.
Ethernet Ports
The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports
are labeled 1 through 4. These ports correspond to the numbered
LEDs on the front of the Router. Connect your network-enabled
computers or any networking devices to one of these ports.
8.
Reset Button
The “Reset” button is used in rare cases when the Router may
function improperly. Resetting the Router will restore the Router’s
normal operation while maintaining the programmed settings. You
can also restore the factory default settings by using the Reset
button. Use the restore option in instances where you may have
forgotten your custom password.
a.
Resetting the Router
Push and hold the Reset button for one second then release
it. When the Power/Ready light becomes solid again, the
reset is complete.
b.
Restoring the Factory Defaults
Press and hold the Reset button for 10 seconds then release
it. When the Power/Ready light becomes solid again, the
restore is complete.
9.
Power Plug
Connect the included 15V DC power supply to this inlet.
Using the wrong type of power adapter may cause damage
to your Router.
�±²±³
´²µ¶µ·¸±
¹º¸¸±¹³·º¸²¶³º¶»º¼�¶¹º½¾¼³±�
(7)
(9)
(6)
(8)
Page 8 / 92
6
Connecting your Router
Positioning your Router
Your wireless connection will be stronger the closer your computer
is to your Router. Typical indoor operating range for your wireless
devices is between 100 and 200 feet. In the same way, your wireless
connection and performance will degrade somewhat as the distance
between your Router connected devices increases. This may or may
not be noticeable to you. As you move farther from your Router,
connection speed may decrease. Factors that can weaken signals
simply by getting in the way of your network’s radio waves are metal
appliances, or obstructions, and walls. Please see “Appendix B:
Important Factors for Placement and Setup” in this User Manual for
more guidelines.
If you have concerns about your network’s performance that might be
related to range or obstruction factors, try moving the computer to
a position between five and 10 feet from the Router, in order to see
if distance is the problem. If difficulties persist even at close range,
please see the Troubleshooting section for solutions.
Page 9 / 92
Connecting your Router
7
section
2
1
3
4
5
6
7
8
9
10
11
12
Connecting your Computers
1.
Power off your computers and networking equipment.
2.
Connect your computer to one of the
YELLOW
RJ45 ports on the
rear of the Router labeled “connections to your computers” by
using an Ethernet networking cable (one Ethernet network cable
is supplied).
Page 10 / 92
8
Connecting your Router
Connecting your ADSL Line
Connection for the Router to the ADSL line varies by country and
region. Typically it involves a microfilter or a microfilter with built-in
splitter to allow simultaneous use of ADSL service and telephone
service on the same telephone line. Please read the following steps
carefully and select appropriate method.
1.
If your telephone service and ADSL service are on the same
telephone line, ADSL microfilters are needed for each telephone
and device, such as answering machine, fax machine, and caller
ID display. Additional splitters may be used to separate telephone
lines for telephone and the Router.
Note:
Do not connect the ADSL microfilter between the wall jack
and the Router—this will prevent ADSL service from reaching
the modem.
2.
If your telephone service and ADSL service are on the same
telephone line and you are using an ADSL microfilter with built-in
splitter, connect the splitter to the telephone wall jack providing
ADSL service. Then, connect the telephone cord from the ADSL
microfilter RJ11 port generally labeled “DSL” to the gray RJ11
port labeled “DSL line” on the back of your Router. Connect
telephony device to the other port on the ADSL splitter commonly
labeled “Phone”. An additional ADSL microfilter is needed for
another telephone and device on the same line.

Rate

4.5 / 5 based on 2 votes.

Popular Belkin Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top