1. Home
    2. /
  2. Manuals
    3. /
  3. Belkin
    4. /
  4. F5D7633-4
    5. /
  5. 3
Page 11 / 94 Scroll up to view Page 6 - 10
Connecting your Router
9
section
2
1
3
4
5
6
7
8
9
10
11
12
Connecting your Computers
1.
Power off your computers and networking equipment.
2.
Connect your computer to one of the
YELLOW
RJ45 ports on the
rear of the Router labeled “connections to your computers” by
using an Ethernet networking cable (one Ethernet network cable
is supplied).
Page 12 / 94
10
Connecting your Router
Connecting your ADSL Line
Connection for the Router to the ADSL line varies by country and
region. Typically it involves a microfilter or a microfilter with built-in
splitter to allow simultaneous use of ADSL service and telephone
service on the same telephone line. Please read the following steps
carefully and select appropriate method.
1.
If your telephone service and ADSL service are on the same
telephone line, ADSL microfilters are needed for each telephone
and device, such as answering machine, fax machine, and caller
ID display. Additional splitters may be used to separate telephone
lines for telephone and the Router.
Note:
Do not connect the ADSL microfilter between the wall jack
and the Router—this will prevent ADSL service from reaching
the modem.
2.
If your telephone service and ADSL service are on the same
telephone line and you are using an ADSL microfilter with built-in
splitter, connect the splitter to the telephone wall jack providing
ADSL service. Then, connect the telephone cord from the ADSL
microfilter RJ11 port generally labeled “DSL” to the gray RJ11
port labeled “DSL line” on the back of your Router. Connect
telephony device to the other port on the ADSL splitter commonly
labeled “Phone”. An additional ADSL microfilter is needed for
another telephone and device on the same line.
Page 13 / 94
11
section
2
1
3
4
5
6
7
8
9
10
11
12
Note:
One RJ11 telephone cord is supplied. When inserting an
RJ11 plug, be sure the tab on the plug clicks into position to
ensure that it is properly seated.
3.
If you have a dedicated ADSL service telephone line with an RJ11
wall jack, simply connect a telephone cord from the wall jack to
the
gray
RJ11 port labeled “DSL line” on the back of
your Router.
4.
If you have an RJ45 wall jack for your ADSL service, connect an
RJ45-to-RJ11 converter to the wall jack. Then connect one end of
a telephone cord to the converter and the other end to the
gray
RJ11 port labeled “DSL line” on the back of your Router.
Note:
ADSL microfilter may or may not be provided depending on
your country.
Connecting your Router
Page 14 / 94
12
Powering Up your Router
1.
Connect the supplied power adapter to the Router power-input
plug labeled “Power”.
Note:
For safety and performance reasons, only use the supplied
power adapter to prevent damage to the Router.
2.
After connecting the power adapter and the power source is turned on,
the Router’s power icon
on the front panel should be on. It might
take a few minutes for the Router to fully start up.
3.
Turn on your computers. After your computers boot up, the LAN
status LED
on the front of the Router will be on for each port
to which a wired computer is connected. These lights show
you the connection and activity status. Now you are ready to
configure the Router for ADSL connection.
Connecting your Router
Page 15 / 94
Setting Up your Computers
13
section
2
1
3
4
5
6
7
8
9
10
11
12
In order for your computer to properly communicate with your Router, you
will need to change your computer’s “TCP/IP Ethernet” settings to “Obtain
an IP address automatically/Using DHCP”. This is normally the default
setting in most home computers.
You can set up the computer that is connected to the ADSL modem FIRST
using these steps. You can also use these steps to add computers to your
Router after the Router has been set up to connect to the Internet.
Manually Configuring Network Adapters in Windows XP, 2000, or NT
1.
Click “Start”, “Settings”, then “Control Panel”.
2.
Double-click on the “Network and dial-up connections” icon
(Windows 2000) or the “Network” icon (Windows XP).
3.
Right-click on the “Local Area Connection” associated with your
network adapter and select “Properties” from the drop-down menu.
4.
In the “Local Area Connection Properties” window, click “Internet
Protocol (TCP/IP)” and click the “Properties” button. The following
screen will appear:
5.
If “Use the following IP address”
(2)
is selected, your Router will need to
be set up for a static IP connection type. Write the address information
the table below. You will need to enter this information into the Router.
6.
If not already selected, select “Obtain an IP address automatically”
(1)
and “Obtain DNS server address automatically”
(3)
. Click “OK”.
Your network adapter(s) are now configured for use with the Router.
(1)
(2)
(3)

Rate

4 / 5 based on 1 vote.

Popular Belkin Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top