1. Home
    2. /
  2. Manuals
    3. /
  3. Belkin
    4. /
  4. F5D7633-4
    5. /
  5. 2
Page 6 / 94 Scroll up to view Page 1 - 5
4
Package Contents
•
ADSL Modem with High-Speed Mode Wireless G Router
•
RJ11 Telephone Cord - Gray
•
RJ45 Ethernet Networking Cable - Yellow
•
ADSL Microfilter*
•
Power Adapter
•
User Manual CD
*ADSL microfilter varies by country. If it’s not included, you will need to purchase
one.
System Requirements
•
An active ADSL service with a telephone wall jack for connecting
the Router
•
At least one computer with a Network Interface Card (NIC) and Internet
browser installed and correctly configured
•
TCP/IP networking protocol installed on each computer connected to
the Router
•
No other DHCP server on your local network assigning IP addresses to
computers and devices
Internet Connection Settings
Please collect the following information from your Internet Service Provider (ISP)
before setting up the ADSL Modem Wireless G Router.
•
Internet connection protocol: _________ (PPPoE, PPPoA, Dynamic IP, Static IP)
•
Multiplexing method or Encapsulation: __________ (LLC or VC MUX)
•
Virtual circuit:
VPI (Virtual Path Identifier)
__________
(a number between 0 and 255)
•
VCI (Virtual Channel Identifier) __________
(a number between 1 and 65535)
•
For PPPoE and PPPoA users: ADSL account user name _____________ and
password _______________
•
For static IP users:
IP Address ___ . ___ . ___ . ___
Subnet Mask ___ . ___ . ___ . ___
Default Gateway Server ___ . ___ . ___ .
•
IP address for Domain Name Server ___ . ___ . ___ . ___ (If given by your ISP)
Note:
See Appendix C in this User Manual for some common DSL Internet
setting parameters. If you are not sure, please contact your ISP.
Make Sure You Have the Following
Page 7 / 94
Knowing your Router
5
The Router is designed to be placed on a desktop. All of the cables exit from
the rear of the Router for better organization and utility. The LED indicators
are easily visible on the front of the Router to provide you with information
about network activity and status.
Front Panel
1.
Power LED
When you apply power to the Router or restart it, a short period of time
elapses while the Router boots up. When the Router has completely
booted up, the Power LED becomes a SOLID light, indicating the Router
is ready for use.
OFF
Router is OFF
Green
Router is ON
Red
Router failed to start
2.
LAN Status LED
These LAN Status LEDs are labeled 1–4 and correspond to the
numbered ports on the rear of the Router. When a computer is properly
connected to one of the LAN ports on the rear of the Router, the LED
will light. Solid GREEN means a computer or a network-enabled device
is connected. When information is being sent over the port, the LED
blinks rapidly. ORANGE indicates a 10Base-T connection.
OFF
No device is connected or computer is
powered off
Orange
Ethernet link is up and 10Base-T
device connected
Orange - blinking
When 10Base-T device transmitting
or receiving data
Green
Ethernet link is up and
100Base-T connected
Green - blinking
When 100Base-T device
transmitting or receiving data
(1)
(4)
(3)
(5)
(2)
section
2
1
3
4
5
6
7
8
9
10
11
12
Page 8 / 94
6
Knowing your Router
3.
WLAN Status LED
The WLAN Status LED is solid GREEN when you enable the
wireless LAN function. It flashes when the Router is transmitting
or receiving data wirelessly.
OFF
WLAN is off
Green
WLAN is up and connected
Green - blinking
When transmitted or receiving data
4.
ADSL LED
The ADSL LED flashes GREEN during negotiation with your ISP.
It stays GREEN when the Router is connected properly to your
ADSL service.
OFF
no ADSL connection
Green
ADSL link is up and connected
Green - blinking
negotiating connection
5.
Internet LED
The Internet LED shows you when the Router is connected to
the Internet. When the LED is OFF, the Router is NOT connected
to the Internet. When the LED is solid GREEN, the Router is
connected to the Internet. When the LED is blinking, the Router
is transmitting or receiving data from the Internet.
OFF
No Internet connection
Green
Connected to the Internet
Green - blinking
When transmitting or receiving data
Red
Failed to get IP
Page 9 / 94
Knowing your Router
7
section
2
1
3
4
5
6
7
8
9
10
11
12
Back Panel
6.
DSL Line
This port is for connection to your ADSL line. Connect your ADSL
line to this port.
7.
Ethernet Ports
The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports
are labeled 1 through 4. These ports correspond to the numbered
LEDs on the front of the Router. Connect your network-enabled
computers or any networking devices to one of these ports.
8.
Reset Button
The “Reset” button is used in rare cases when the Router may
function improperly. Resetting the Router will restore the Router’s
normal operation while maintaining the programmed settings. You
can also restore the factory default settings by using the Reset
button. Use the restore option in instances where you may have
forgotten your custom password.
a.
Resetting the Router
Push and hold the Reset button for one second then release
it. When the Power/Ready light becomes solid again, the
reset is complete.
b.
Restoring the Factory Defaults
Press and hold the Reset button for 10 seconds then release
it. When the Power/Ready light becomes solid again, the
restore is complete.
9.
Power Plug
Connect the included 15V DC power supply to this inlet.
Using the wrong type of power adapter may cause damage
to your Router.
(7)
(8)
(9)
(6)
Page 10 / 94
8
Connecting your Router
Positioning your Router
Your wireless connection will be stronger the closer your computer
is to your Router. Typical indoor operating range for your wireless
devices is between 100 and 200 feet. In the same way, your wireless
connection and performance will degrade somewhat as the distance
between your Router connected devices increases. This may or may
not be noticeable to you. As you move farther from your Router,
connection speed may decrease. Factors that can weaken signals
simply by getting in the way of your network’s radio waves are metal
appliances, or obstructions, and walls. Please see “Appendix B:
Important Factors for Placement and Setup” in this User Manual for
more guidelines.
If you have concerns about your network’s performance that might be
related to range or obstruction factors, try moving the computer to
a position between five and 10 feet from the Router, in order to see
if distance is the problem. If difficulties persist even at close range,
please see the Troubleshooting section for solutions.

Rate

4 / 5 based on 1 vote.

Popular Belkin Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top