1. Home
    2. /
  2. Manuals
    3. /
  3. Belkin
    4. /
  4. F5D7632-4
    5. /
  5. 2
Page 6 / 108 Scroll up to view Page 1 - 5
6
Make Sure You Have the Following
6
Package Contents
•
ADSL Modem with Wireless G Router
•
RJ11 Telephone Cord - Gray
•
RJ45 Ethernet Networking Cable — Yellow
•
USB 1.0 Cable — Blue
•
ADSL Microfilter*
•
Power Adapter
•
User Manual CD
*ADSL microfilter varies by country. If it’s not
included, you will need to purchase one.
System Requirements
•
An active ADSL service with a telephone wall jack for connecting the Router
•
At least one computer with a Network Interface Card (NIC) and Internet
browser installed and correctly configured
•
TCP/IP networking protocol installed on each computer connected to
the Router
•
No other DHCP server on your local network assigning IP addresses to
computers and devices
Internet Connection Settings
Please collect the following information from your Internet Service
Provider (ISP) before setting up the ADSL Modem Wireless G Router.
•
Internet connection protocol: _________ (PPPoE, PPPoA, Dynamic IP,
Static IP)
•
Multiplexing method or Encapsulation: __________ (LLC or VC MUX)
•
Virtual circuit:
VPI (Virtual Path Identifier)
__________
(a number between 0 and 255)
•
VCI (Virtual Channel Identifier) __________
(a number between 1 and 65535)
•
For PPPoE and PPPoA users: ADSL account user name _____________
and password _______________
•
For static IP users:
IP Address ___ . ___ . ___
Subnet Mask ___ . ___ . ___
Default Gateway Server ___ . ___ . ___ .
•
IP address for Domain Name Server ___ . ___ . ___ . ___ (If given by
your ISP)
Note:
See Appendix C in this User Manual for some common DSL
Internet setting parameters. If you are not sure, please contact your ISP.
Page 7 / 108
7
Knowing your Router
7
ADSL LED
Power LED
LAN Status LED
(1-4)
Wireless LAN (WLAN)
Status LED
Internet LED
The Router has been designed to be placed on a desktop. All of the cables
exit from the rear of the Router for better organization and utility. The LED
indicators are easily visible on the front of the Router to provide you with
information about network activity and status.
Front Panel
The illustration
shows the front
panel of the
Router:
1. Power LED
When you apply
power to the Router
or restart it, a short period of time elapses while the Router boots up. When
the Router has completely booted up, the Power LED becomes a GREEN light,
indicating the Router is ready for use.
Power
OFF
Green
Red
Power off
Power on
Router failed to start
2. LAN Status LEDs
These LAN Status LEDs are labeled 1–4 and correspond to the numbered
ports on the rear of the Router. When a computer is properly connected to
one of the LAN ports on the rear of the Router, the LED will light. Solid GREEN
means a computer or a network-enabled device is connected. When information is being
sent over the port, the LED blinks rapidly. ORANGE indicates a 10Base-T connection.
LAN
—
OFF
No device is connected
Orange
Ethernet link is up and 10Base-T device connected
Orange
blinking
When 10Base-T device transmitting or receiving data
Green
Ethernet link is up and 100Base-T connected
Green
blinking
When 100Base-T device transmitting or receiving data
section
2
1
3
4
5
6
7
8
9
10
11
12
Page 8 / 108
8
Knowing your Router
3. WLAN Status LED
The WLAN Status LED is solid GREEN when you enable the wireless LAN
function. It flashes when the Router is transmitting or receiving data wirelessly.
WLAN
OFF
WLAN is off
Green
WLAN is up and connected
Green
blinking
When transmitting or receiving data
4. ADSL LED
The ADSL LED flashes GREEN during negotiation with your ISP. It stays
GREEN when the Router is connected properly to your ADSL service.
ADSL
OFF
No ADSL connection
Green
blinking
Negotiating connection
Green
ADSL link is up and connected
5. Internet LED
The Internet LED shows you when the Router is connected to
the Internet. When the LED is OFF, the Router is NOT connected
to the Internet. When the LED is solid GREEN, the Router
is connected to the Internet. When the LED is blinking, the
Router is transmitting or receiving data from the Internet.
Internet
OFF
No Internet connection
Green
Connected to the Internet
Green
blinking
When transmitting or receiving data
Red
Failed to get IP
Page 9 / 108
Knowing your Router
9
section
2
1
3
4
5
6
7
8
9
10
Back Panel
The following figure illustrates the rear panel of your Router.
6.
DSL Line
This port is for connection to your ADSL line.
Connect your ADSL line to this port.
7.
Power Plug
Connect the included 15V DC power supply to this inlet. Using the
wrong type of power adapter may cause damage to your Router.
8.
Reset Button
The “Reset” button is used in rare cases when the Router may function
improperly. Resetting the Router will restore the Router’s normal
operation while maintaining the programmed settings. You can also
restore the factory default settings by using the Reset button. Use the
restore option in instances where you may have forgotten your custom
password.
a.
Resetting the Router
Push and hold the “Reset” button for one second then release it.
When the “Power/Ready” light becomes solid again, the reset is
complete.
b.
Restoring the Factory Defaults
Press and hold the Reset button for five seconds then release it.
When the Power/Ready light becomes solid again, the restore is
complete.
9.
Ethernet Ports
The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports are
labeled 1 through 4. These ports correspond to the numbered LEDs on
the front of the Router. Connect your network-enabled computers or
any networking devices to one of these ports.
(9)
(8)
(7)
(6)
Page 10 / 108
�±²³�´µ±²¶·´±·¸±¹º·�±»¼¹´³º¶
Á³¶³´
10
Connecting your Router
Positioning your Router
Your wireless connection will be stronger the closer your computer is to
your Router. Typical indoor operating range for your wireless devices is
between 100 and 200 feet. In the same way, your wireless connection and
performance will degrade somewhat as the distance between your Router
connected devices increases. This may or may not be noticeable to you.
As you move farther from your Router, connection speed may decrease.
Factors that can weaken signals simply by getting in the way of your
network’s radio waves are metal appliances, or obstructions, and walls.
Please see “Appendix B: Important Factors for Placement and Setup” in this
User Manual for more guidelines.
If you have concerns about your network’s performance that might be
related to range or obstruction factors, try moving the computer to a
position between five and 10 feet from the Router, in order to see if distance
is the problem. If difficulties persist even at close range, please see the
Troubleshooting section for solutions.
Connecting your Computers
1.
Power off your computers and networking equipment.
2.
Connect your computer to one of the YELLOW RJ45 ports on the rear
of the Router labeled “connections to your computers” by using an
Ethernet networking cable (one Ethernet network cable is supplied).

Rate

3.5 / 5 based on 2 votes.

Popular Belkin Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top