Page 36 / 106
Scroll up to view Page 31 - 35
34
Wireless G Router
SECTIONS
Table of Contents
1
2
3
4
6
7
8
9
10
5
ALTERNATE SETUP METHOD
Setting your ISP Connection Type to PPPoE
Most DSL providers use PPPoE as the connection type� If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into
the service� If you have an Internet connection in your home or small office that doesn’t require a modem, you may also use PPPoE�
Your connection type is PPPoE if:
- Your ISP gave you a user name and password, which is required to
connect to the Internet;
- Your ISP gave you software such as WinPOET or Enternet300 that you
use to connect to the Internet; or
- You have to double-click on a desktop icon other than your browser to
get on the Internet�
(1)
(2)
(3)
(4)
(5)
Page 37 / 106
35
Wireless G Router
SECTIONS
Table of Contents
1
2
3
4
6
7
8
9
10
5
ALTERNATE SETUP METHOD
1�
User Name
This space is provided to type in your user name that was assigned by
your ISP�
2�
Password
Type in your password and re-type it into the “Retype Password” box to
confirm it�
3�
Service Name
A service name is rarely required by an ISP� If you are not sure if your
ISP requires a service name, leave this blank�
4�
MTU
The MTU setting should never be changed unless your ISP gives you
a specific MTU setting� Making changes to the MTU setting can cause
problems with your Internet connection including disconnection from the
Internet, slow Internet access, and problems with Internet applications
working properly�
5�
Maximum Idle Time
This feature is used to automatically disconnect the Router from your
ISP when there is no activity for a specified period of time� For instance,
placing a check mark next to this option and entering “5” into the minute
field will cause the Router to disconnect from the Internet after five
minutes of no Internet activity� This option should be used if you pay for
your Internet service by the minute�
Page 38 / 106
36
Wireless G Router
SECTIONS
Table of Contents
1
2
3
4
6
7
8
9
10
5
ALTERNATE SETUP METHOD
Setting your Internet Service Provider (ISP) Connection Type to Point-to-Point Tunneling Protocol (PPTP)
[European Countries Only]� Some ISPs require a connection using PPTP
protocol, a type of connection most common in European countries�
This sets up a direct connection to the ISP’s system� Type in the
information provided by your ISP in the space provided� When you
have finished, click “Apply Changes”� After you apply the changes, the
“Internet Status” indicator will read “Connected” if your Router is set
up properly�
(1)
(2)
(3)
(4)
(5)
(a)
(b)
(c)
Page 39 / 106
37
Wireless G Router
SECTIONS
Table of Contents
1
2
3
4
6
7
8
9
10
5
ALTERNATE SETUP METHOD
1�
User ID
Provided by your ISP� Enter your PPTP User ID here�
2�
Password
Provided by your ISP� Type in your password here�
3�
PPTP Gateway
Provided by your ISP� Enter your PPTP gateway/service IP address here�
4�
Idle Time Out
This feature is used to automatically disconnect the Router from your
ISP when there is no activity for a specified period of time� For instance,
entering “10” into the minute field will cause the Router to disconnect
from the Internet after 10 minutes of no Internet activity� This option
should be used if you pay for your Internet service by the minute�
5�
Get IP by DHCP
Select the method of getting your Internet IP address from your ISP
server� It depends on your ISP service type� Check this box if your
ISP will automatically assign an IP address for you� If you are not
sure of this, please contact your ISP’s technical-support hotline� If
your ISP provided an IP address for you, enter the information in the
following fields�
a�
IP Address
Provided by your ISP� Enter the IP address here�
b�
Subnet Mask
Provided by your ISP� Enter the IP address here�
c�
Default Gateway
Provided by your ISP� Enter the gateway address here�
Page 40 / 106
38
Wireless G Router
SECTIONS
Table of Contents
1
2
3
4
6
7
8
9
10
5
ALTERNATE SETUP METHOD
Setting your Connection Type if you are a Telstra
®
BigPond/OptusNet Cable User
Follow the on-screen steps and click “Apply Changes” to complete
your setup�
Setting Custom Domain Name Server (DNS) Settings
A “Domain Name Server” is a server located on the Internet that
translates Universal Resource Locators (URLs) like “www�belkin�com”
into IP addresses� Many Internet Service Providers (ISPs) do not require
you to enter this information into the Router� The “Automatic from ISP”
box should be checked if your ISP did not give you a specific DNS
address� If you are using a static IP connection type, then you may
need to enter a specific DNS address and secondary DNS address for
your connection to work properly� If your connection type is dynamic
or PPPoE, it is likely that you do not have to enter a DNS address�
Leave the “Automatic from ISP” box checked� To enter the DNS
address settings, uncheck the “Automatic from ISP” box and enter your
DNS entries in the spaces provided� Click “Apply Changes” to save
the settings�
19216811.live