Bandluxe R100 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 65 Scroll up to view Page 21 - 25

WiFi Setup

25

WPA-Enterprise

This option features WPA used in coordination with a RADIUS server.

(This should only be used when a RADIUS server is connected to the

Router.)

Encryption:

Choose

TKIP

or

AES

from the drop down list. (AES is a

stronger encryption method than TKIP.)

RADIUS Server:

Enter the IP Address of the RADIUS server.

RADIUS Port:

Enter the port number of the RADIUS server. The default

value is 1812.

Shared Key:

Enter the key shared between the Router and the server.

Key Renewal:

Enter a key renewal value to tell the Router how often it

should change the encryption keys. The value must be between

60-99999.

WPA2-Enterprise

This option features WPA2 used in coordination with a RADIUS server.

(This should only be used when a RADIUS server is connected to the

Router.)

Encryption:

Choose

AES

or

WPA-TKIP

or

WPA2-AES

from the drop

down list.

Page 27 / 65

WiFi Setup

26

RADIUS Server:

Enter the IP Address of the RADIUS server.

RADIUS Port:

Enter the port number of the RADIUS server. The default

value is 1812.

Shared Key:

Enter the key shared between the Router and the server.

Key Renewal:

Enter a key renewal value to tell the Router how often it

should change the encryption keys. The value must be between

60-99999.

RADIUS

RADIUS stands for Remote Authentication Dial-In User Service. It is a

networking protocol that uses access servers to provide centralized

management of access to large networks.

RADIUS Server:

Enter the IP Address of the RADIUS server.

RADIUS Port:

Enter the port number of the RADIUS server. The default value is

1812.

Shared Key:

Enter the key shared between the Router and the server.

Encryption:

Select either 64-bits or 128-bits from the drop-down list The 64-bits

encryption requires 10 hexadecimal digits. The 128-bits encryption requires 26

hexadecimal digits .You can set up to four different keys.

Passphrase:

Strings of hexadecimal characters are not easy to remember. This

conversion utility converts a simple word or phrase into hex, so that you can easily

remember and regenerate the pass-phrase.

TX Key:

You can specify which key you want to use for the WiFi network.

Page 28 / 65

WiFi Setup

27

Disabled

If you do not want to use any security method for your wireless network,

choose

Disabled

.

Advanced WiFi Setting

AP Isolation:

This isolates all wireless clients and wireless devices on

your network from each other. Wireless devices will be able to

communicate with the Router but not with each other.

Frame Burst:

Enabling this option may provide your network with greater

performance.

Authentication Type:

The default is Open System authentication, where

the sender and the recipient do not use a WEP key for authentication. To

use a WEP key for authentication, select Shared Key.

Basic Rate:

The Basic Rate setting is not actually one rate of

transmission but a series of rates at which the Router can transmit. The

Router advertises its Basic Rate to the other wireless devices in your

network, so they know which rates are used. The Router also advertises

that automatically selects the best rate for transmission. The default

setting is

Auto

, where the Router can transmit at all standard wireless

rates. The Basic Rate is not the actual rate of data transmission. If you

want to specify the Router’s rate of data transmission, configure the

Transmission Rate

setting.

Page 29 / 65

WiFi Setup

28

Transmission Rate:

The rate of data transmission should be set

depending on the speed of your wireless network. You can select from a

range of transmission speeds.

CTS Protection Mode:

CTS (Clear To Send) is a function used to

minimize collisions among wireless devices on a wireless local area

network (LAN). The default setting is

Auto

and the Router automatically

uses CTS Protection Mode when your Wireless-G products are

experiencing severe problems and are not able to transmit to the Router

in an environment with heavy traffic. This function boosts the Router’s

ability to catch all Wireless-B and Wireless-G transmissions, but it

severely decreases performance.

Beacon interval:

Beacons are packets sent by an Access Point to

synchronize a wireless network. Specify a value. 100 is the default

setting.

DTIM Interval:

The default setting for DTIM (Delivery Traffic Indication

Message) is 3. A DTIM is a countdown informing clients of the next

window for listening to broadcast and multicast messages.

Fragmentation Threshold:

The fragmentation threshold, which is

specified in bytes, determines whether packets will be fragmented.

Packets exceeding the setting value will be fragmented before

transmission. 2346 is the default setting.

RTS Threshold:

This value should remain at its default setting of 2347. If

inconsistent data flow is a problem, only a minor modification should be

made.

Page 30 / 65

WiFi Setup

29

WiFi Clients Filter

You can allow or deny specific users to access your wireless network by

using the WiFi Clients Filter.

Service:

To use the WiFi Clients Filter, select Enabled. To disable it, select

Disabled

.

Filtering By:

You can filter users by two methods:

Prevent

the listed PCs from

accessing the wireless network, or

Permit

the listed PCs to access the wireless

network. Select the method you want.

Filtered Client List

Enter MAC addresses in the Filtered Client List section, and click

Save Settings

.

To display a list of network users, click

Wireless Client List

.

Rate

Popular Bandluxe Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share