Axesstel MV600 Router Manual PDF (Setup & Configuration Guide)

Page 51 / 58 Scroll up to view Page 46 - 50

50

•

If you are still unable to access the Internet after verifying these

settings, please contact your Service Provider Technical Support.

Problem:

•

The Install software completed installation, but my web browser

doesn’t work.

•

I am unable to connect to the Internet. The Modem’s “Signal” light is

on and the “Connect” light is on.

Solution:

If the “Signal” light is on, and the “Connect” light is on, but you are unable to

access the Internet, there may be third-party firewall software installed on

the computer attempting to access the Internet. Examples of third-party

firewall software are ZoneAlarm, BlackICE PC Protection, McAfee Personal

Firewall, and Norton Personal Firewall.

If you do have firewall software installed on your computer, please make

sure that you properly configure it. You can determine if the firewall software

is preventing Internet access by temporarily turning it off. If, while the

firewall is disabled and Internet access works properly, you will need to

change the firewall settings to function properly when it is turned on.

Please refer to the instructions provided by the publisher of your firewall

software for instructions on configuring the firewall to allow Internet access.

If you are still unable to access the Internet after disabling any firewall

software, please contact your Service Provider Technical Support.

Problem:

I can’t connect to the Internet wirelessly from my computer but it works if I

use the Ethernet cable.

Solution:

If you are unable to connect to the Internet from a wireless computer,

please do the following:

1. Look at the lights on your Modem. Your Modem’s lights should be as

follows:

•

The “Power” light should be on.

Page 52 / 58

51

•

The “Connected” light should be on and not blinking.

•

The “WAN” light should be either on or blinking.

2. Open your wireless utility software by clicking on the icon in the

system tray at the bottom, right-hand corner of the screen.

3. The exact window that opens will vary depending on the model of

wireless card you have; however, any of the utilities should have a list

of “Available Networks”—those wireless networks it can connect to.

Problem:

My wireless network performance is inconsistent.

Data transfer is sometimes slow.

Signal strength is poor.

I am having difficulty establishing and/or maintaining a Virtual Private

Network (VPN) connection.

Solution:

Wireless technology is radio-based, which means connectivity and the

throughput performance between devices decreases when the distance

between devices increases. Other factors that will cause signal degradation

(metal is generally the worst culprit) are obstructions such as walls and

metal appliances. As a result, the typical indoor range of your wireless

devices will be between 100 to 200 feet. Note also that connection speed

may decrease as you move farther away from the Modem or access point.

In order to determine if wireless issues are related to range, we suggest

temporarily moving the computer, if possible, five to 10 feet away from the

Modem.

Changing the Wireless Channel

- Depending on local wireless traffic and

interference, switching the wireless channel of your network can improve

performance and reliability. The default channel the Modem is shipped with

is channel 11. You may choose from several other channels depending on

your region (see the section titled “Changing the Wireless Channel” on page

41 for instructions on how to choose other channels).

Limiting the Wireless Transmit Rate

- Limiting the wireless transmit rate can

help improve the maximum wireless range and connection stability. Most

wireless cards have the ability to limit the transmission rate. To change this

property, go to the Windows Control Panel, open “Network Connections”

Page 53 / 58

52

and double-click on your wireless card’s connection. In the “Properties”

dialog, select the “Configure” button on the “General” tab (Windows 98

users will have to select the wireless card in the list box and then click

“Properties”), then choose the “Advanced” tab and select the rate property.

Wireless client cards are usually set to automatically adjust the wireless

transmit rate for you, but doing so can cause periodic disconnects when the

wireless signal is too weak; as a rule, slower transmission rates are more

stable.

Experiment with different connection rates until you find the best one for

your environment; note that all available transmission rates should be

acceptable for browsing the Internet. For more assistance, see your

wireless card’s user manual.

Page 54 / 58

53

Technical Specifications

This chapter provides technical product data for the Modem.

Radio frequency and electrical specifications

Frequency

Range

MV410

Rx: 463 ~ 468 MHz

Tx: 453 ~ 458 MHz

Frequency

Range

MV420 & MV440

Rx: 859.64 ~ 893.37 MHz

Tx: 824.64 ~ 848.37 MHz

Frequency

Range

MV430 & MV440

Rx: 1930 ~ 1989.95 MHz

Tx: 1850 ~ 1909.95 MHz

Channel Bandwidth

CDMA 1.23 MHz

Stability of frequency

0.4 ppm

External appearance (mm)

160 x 178 x 40 mm

Weight

600 g (with battery)

Sending output

maximum 0.23W E.R.P

Temperature of operation

Relative humidity

-20 ~ +60 degrees Celsius

5% ~ 90%

Adapter

Input: AC 110~240V 50~60Hz

Output: DC 12V/2A

Battery

Operation

2.5 Hrs

AXT v7.0

Page 55 / 58

54

Appendix A: Glossary

1X

One Times Radio Transmission Technology (the “one times”

refers to the frequency spectrum). Supports Internet connections

with data rates up to 153 Kbps. Actual speed depends on the

network conditions. Compare to 1x EV-DO.

1x-EVDO

A high speed standard for cellular packet data communications

Rev. A supports Internet connections with data rates up to3.1

Mbps (downlink from the network) and 1.8 Mbps (uplink to the

network).

Rev. 0 supports Internet connections with data rates up to 2.4

Mbps (downlink from the network) and 153 Kbps (uplink to the

network).

Average data rates are roughly: for Rev. A: 600–1300 Kbps

(downlink from the network) and 300–400 Kbps (uplink to the

network); for Rev. 0: 400–700 Kbps (downlink from the network)

and 40°80 Kbps (uplink to the network).

Actual speed depends on the network conditions. Compare to 1X.

bps

bits per second—The actual data speed over the transmission

medium.

CDMA

Code Division Multiple Access—A wideband spread spectrum

technique used in digital cellular, personal communications

services, and other wireless networks. Wide channels (1.25 MHz)

are obtained through spread spectrum transmissions, thus

allowing many active users to share the same channel. Each user

is assigned a unique digital code, which differentiates the

individual conversations on the same channel.

CDMA 1X

Also known as 1X, this is a high speed standard for CDMA

cellular communications.

dormant

The packet data connection has the logical PPP session left open

while the underlying physical link (the radio channel) is released.

When traffic is to resume, a radio channel is reacquired and the

original PPP session resumes.

Rate

Popular Axesstel Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share