1. Home
    2. /
  2. Manuals
    3. /
  3. Axesstel
    4. /
  4. MV430i
    5. /
  5. 4
Page 16 / 58 Scroll up to view Page 11 - 15
15
Connecting and Configuring your Modem
Each Modem has been provisioned at the factory for use with a particular service
provider. This sets the Modem to use particular radio channels and enables
services specific for that provider.
MV400-series and MV400i-series
: Although the Modem comes with drivers and
enabling software, you don’t have to install and use them if you simply want to
connect to the Internet through the Ethernet (RJ-45) ports
, assuming that your
Modem has been activated with the network. Simply connect your computer with
the Modem using the provided Ethernet (RJ-45) cable and you are ready to use
the Internet.
However, if you want to connect to the Internet through USB port
, you must install
AxessManager software.
MV400R-series
: You must install AxessManager software to connect and
configure your Modem.
If you choose to install the drivers and its enabling software (the AxessManager)
you will have more controls of the Modem performances and settings. You will
also have access to more advance features of the Modem such as Wi-Fi
configuration (not applicable to MV400i-series), USB connection and password
management.
This chapter provides the step-by-step process to install the AxessManager
connectivity software.
Install Software
Axesstel has provided our AxessManager software to make installing your Modem
a simple and easy task. You can use it to get your Modem up and running in
minutes. The AxessManager software requires that your Windows Me, 2000, or
XP computer be connected directly to your Modem.
IMPORTANT
: Run the installation software from the computer that is going to be
the main connection with the Modem.
DO NOT CONNECT THE MODEM AT THIS TIME.
Step 1
│
Run the Install Software
1.1.
Shut down any programs that are running on your computer at this time.
Page 17 / 58
16
1.2
Make sure you have the following items at the computer that is going to be
the main connection with the Modem. DO NOT CONNECT THE MODEM
AT THIS TIME.
•
The Installation Software CD with User Manual
•
The Modem
•
The Modem’s Power Supply
•
RJ45 Ethernet Networking Cable
1.3
Turn off any firewall or Internet-connection-sharing software on your
computer.
1.4
Insert the installation software CD into your CD-ROM drive. The Installation
screen will automatically appear on your screen within 15 seconds. If it does
not, select your CD-ROM drive from “My Computer” and double-click on the
file named “AxessManager_0992_Setup.exe” on the CD-ROM.
IMPORTANT
: If you have MV400-series or MV400i-series, continue to the next
steps below. If you have MV400R-series, skip the rest of this chapter and go to
AxessManager Operation Guide section.
Step 2
│
Set up the Hardware
2.1.
Make sure your Modem is not connected to any power source and all the
LED are OFF.
2.2
Locate the CAT-5 Ethernet cable that is included with your Modem. Plug
one end of this cable into ANY one of the Ethernet ports on your Modem.
Plug the other
end of the cable into the networking port on your computer.
2.3
Locate the power supply that is included with your Modem. Plug the power
supply’s small connector into the power port on the Modem. Plug the power
supply into an empty power outlet.
2.4
Switch on the Modem. Look at the Power LED on top of the Modem and
make sure the lights are ON.
2.5
Wait for a few seconds for the Modem to search for service network. Once
the Modem finds a suitable network, observe the Signal LED turns to Red,
Orange or Green depending on the strength of acquired signal. Refer to the
Signal Strength LED description for more details.
Page 18 / 58
17
Step 3
│
Preparing your PC
Your Modem’s Ethernet is configured with DHCP by default. This means that IP
address of your PC is automatically assigned by the Modem. Make sure that your
PC has the correct TCP/IP setting for its "Local Area Connection" by following the
steps below.
3.1 Click "Start", select "Connect To"
and scroll down to "Show all
connections" and left click it.
3.2 Right click "Local Area
Connection" scroll down to
"Properties" and left click it
3.3 Select the “Internet Protocol
(TCP/IP)”. Press the “Properties” button.
If there is no TCP/IP line listed, you will
need to install TCP/IP first.
Page 19 / 58
18
3.4 Check “Obtain an IP address
automatically”
3.5 Check “Obtain DNS Server
address automatically”
3.6 Click Ok to exit Properties
3.7 If asked to re-start the PC, click
“YES”.
Page 20 / 58
19
Using USB with your Modem
The Modem has one USB Type B port to provide connectivity for computers
equipped with USB. If you choose to use the USB with your Modem, you first
need to install the provided USB device driver into your computer.
This chapter provides the step-by-step process to install the USB device driver.
IMPORTANT
: Run the USB device driver installation from the computer that is
going to be the main connection with the Modem.
DO NOT CONNECT THE MODEM AT THIS TIME.
Step 1
│
Run the Setup Software
1.1.
Shut down any programs that are running on your computer at this time.
1.2
Make sure you have the following items at the computer that is going to be
the main connection with the Modem. DO NOT CONNECT THE MODEM
AT THIS TIME.
•
The Install Software CD with User Manual
•
The Modem
•
The Modem’s Power Supply
•
USB Cable
1.3
Insert the Install software CD into your CD-ROM drive. Locate the folder
“Driver”. You will see two subfolders: “Install 32” and “Install 64”. For PC
with
Windows Vista 64
, use “Install 64”. Otherwise, use “Install 32”.
1.4
Press “MSP_Install.exe”. The following screen will appear. Select “Install”.

Rate

4 / 5 based on 1 vote.

Popular Axesstel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top