Page 66 / 89
Scroll up to view Page 61 - 65
5
Click
Properties
to open the Properties window.
6
Select
Internet Protocol Version 4 (TCP/IPv4)
and click
Properties
.
7
Select
Obtain an IP address automatically
and
Obtain DNS server
address automatically
, unless instructed otherwise by your cable provider.
8
Click
OK
to close the Properties windows and then click
Close
to back out
of the remaining setup screens.
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
66
Page 67 / 89
TCP/IP Configuration for MacOS X
Follow these steps to configure the Ethernet interface for use with Touchstone prod-
ucts.
1
Open System Preferences, either by choosing System Preferences from the
Apple menu or by clicking the System Preferences icon in the dock.
2
Click the
Network
icon.
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
67
Page 68 / 89
3
Choose
Automatic
from the Location drop-down menu, and
Built-in Eth-
erne
t from the Show menu.
4
Choose the TCP/IP tab, if necessary.
5
Choose
Using DHCP
from the Configure IPv4 menu.
6
If necessary, click the
Renew DHCP Lease
button.
7
Close the System Properties application.
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
68
Page 69 / 89
Power
DS
US
Online
Link
LAN 1
LAN 2
LAN 3
LAN 4
WLAN
Telephone 1
Telephone 2
Touchstone
Telephony
Modem
TM
Secure
69
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
Touchstone WTM652 Telephony Modem User’s Guide
Using the Telephony Modem
This chapter describes the controls and features available on the Touchstone Tele-
phony Modem, and covers basic troubleshooting procedures.
•
Setting up Your Computer to Use the Telephony Modem
•
Indicator Lights for the WTM652A/B Models
•
Indicator Lights for the WTM652G Model
•
Using the Reset Buttons
Setting up Your Computer to Use the Telephony
Modem
Follow the instructions in the information packet supplied by your cable company.
Contact your cable company if you need help setting up your computer.
Indicator Lights for the WTM652A/B Models
The Touchstone Telephony Modem has 13 LED indicator lights to assist in trou-
bleshooting.
Wiring Problems
If the Telephony Modem begins flashing all its lights for more than 10 seconds, this
indicates a problem with the telephone wiring — the red and green wires may be
shorted (touching), or there may be undesired voltage on the lines. If this pattern
persists for more than 10 seconds, disconnect the telephone lines from the Tele-
phony Modem, then call a wiring technician for assistance.
Page 70 / 89
Patterns: Normal Operation (WAN)
The following table shows light patterns for the cable connection during normal op-
eration.
Mode
Power
DS
US
Online
Link
AC Power
On
On
=
Connected
to the
Internet
Flash
= Not
connected
to the
Internet
On
=
Connected
to the
Internet
Flash
= Not
connected
to the
Internet
On
=
Internet
Available
Off =
Internet not
available
On
=
Computer
Connected
Off =
Computer
not
connected
Flash
=
Computer
Activity
No AC Power
Off
Off
Off
Off
Off
Firmware
Upgrade
On
Flash
Flash
On
(normal
operation)
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
70
19216811.live