1. Home
    2. /
  2. Manuals
    3. /
  3. Arris
    4. /
  4. WTM652
    5. /
  5. 10
Page 46 / 89 Scroll up to view Page 41 - 45
•
Day: choose the beginning and ending day of the week that this block is
effective.
•
Time: choose the beginning and end time of day that this block is effec-
tive.
•
Enable: check this box to activate the block, or clear the check to disable
the block.
3
Click the
Save
button to save your changes.
4
Proceed to
Configuring MAC Address Filtering
.
Configuring MAC Address Filtering
Follow these steps to configure MAC Address filtering.
1
Click the Firewall link in the navigation menu, then click MAC Address Filter-
ing.
The MAC Address Filtering window appears.
2
Click the Add button to add a blank row to the filter list.
3
Enter the MAC address of the computer you want to add to the filter. Do not
enter colons or dashes in between the hex digits. For information about find-
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
46
Page 47 / 89
ing the MAC address of a computer, go to
Setting the MAC Address
and see
the sidebar.
Note
: Make sure you enter the MAC address correctly. The Telephony
Modem may completely block access if you enter an incorrect address.
4
Click the
Save
button to save your changes.
5
Proceed to
Configuring DDNS
.
Configuring DDNS
The public IP addresses assigned to your Telephony Modem can change from time
to time. If you are providing services from your private network (using the Virtual
Servers feature), you should use Dynamic DNS (DDNS) to associate your current
IP address with a domain name. The Telephony Modem directly supports several
major DDNS providers.
After setting up a DDNS account, follow these steps to configure the Telephony
Modem to contact the DDNS provider.
1
Click the Firewall link in the navigation menu, then click DDNS.
The DDNS window appears.
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
47
Page 48 / 89
2
Choose your DDNS provider from the
DDNS Service
drop-down menu.
3
Enter your DDNS account name, password, and DDNS domain name in the
appropriate fields.
4
Click the
Update DDNS
button.
Note
: Your domain name may not be immediately associated with your cur-
rent IP address. Updated DNS information takes some time to propagate
across the Internet.
5
Proceed to
Configuring Wireless Bridging
.
Configuring Wireless Bridging
The Telephony Modem supports the Wireless Distribution System (WDS), a common
bridging standard that allows you to extend the range of a wireless network by con-
necting several wireless routers.
Keep the following in mind when setting up wireless bridging:
•
One device (in this case, the Telephony Modem) acts as the router. Other
wireless routers must be configured as Access Points. See the documenta-
tion for your additional devices for instructions for using them as Access
Points.
•
While the Telephony Modem has the ability to be configured as an Access
Point, doing so disables the router function and therefore disables Internet
access through the Telephony Modem.
•
Each wireless router must support WDS.
•
The Router and each Access Point must use the same channel number and
security settings.
•
If MAC address filtering is enabled, the router and each Access Point must
have the MAC addresses of the other devices in their access lists.
Follow these steps to set up wireless bridging. The steps assume you have already
configured the devices as described above.
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
48
Page 49 / 89
1
In the Telephony Modem, click the Wireless Setup link in the navigation
menu, then click Wireless Bridging.
The Wireless Bridging window appears.
2
Check the
Enable Wireless Bridging
box.
3
(recommended) If you want to specify which Access Points are allowed to
connect to your network, check the
Enable ONLY Specific Access Points
to Connect
box and enter the MAC address of each Access Point in the AP1
through AP4 fields. You can enter up to four Access Points.
Note
: Most wireless devices have their MAC addresses printed on a label at-
tached to the back or bottom of the unit. Make sure you enter the wireless
(WLAN) MAC address; the Ethernet and WAN connections have different
MAC addresses.
4
Click the
Save
button to save your changes.
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
49
Page 50 / 89
Configuring RIP
Enabling RIP (Router Information Protocol) allows the WTM652 to act as a router
in your local network. RIP is primarily intended for use in an office environment.
Requirements
To successfully configure RIP, you must:
•
have a static IP address assigned by your cable provider
•
disable Network Address Translation (NAT) on the WTM652 (which means
you must either assign static IP addresses to all devices in your local net-
work or use a DHCP server to assign addresses)
Action
Follow these steps to configure RIP.
1
Click the Lan Setup link in the navigation menu, then click RIP Settings.
The RIPv2 Settings window appears:
Touchstone WTM652 Telephony Modem User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Wireless
Configuration
Ethernet
Configuration
Usage
Troubleshooting
Glossary
50

Rate

3.5 / 5 based on 2 votes.

Popular Arris Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top