Arris TG862G-NA Router Manual PDF (Setup & Configuration Guide)

Page 16 / 56 Scroll up to view Page 11 - 15

3

Push the battery pack into the bay until it seats into place.

If you are tak-

ing the battery out of the Telephony Gateway, position your ﬁnger

in the battery opening area and use leverage to dislodge the battery

while pulling it straight back.

Note

: The Telephony Gateway will not begin operating until you apply AC

power.

4

Replace the door. To do so, place the hinge tabs of the battery door into the

receiver slots inside the Telephony Gateway battery compartment on the

opposite end of the battery opening. Rotate the door toward the unit until

the latch snaps back into place.

Note

: Telephony Gateways use a Lithium-Ion battery pack. Please recycle

or dispose of the battery responsibly and in accordance with local ordi-

nances.

Touchstone TG862 Telephony Gateway User’s Guide

Safety

Getting

Started

Battery

Installation

Ethernet

Conﬁguration

Usage

Troubleshooting

Glossary

16

Battery

Compartment

Receiver

Slots

Hinge Tabs

Page 17 / 56

TG862 Extended Battery Installation and Replace-

ment

Use this procedure to install or replace the backup battery.

1

Press down and pull back on the latch holding the battery door (on the bot-

tom of the Telephony Gateway). Pull the door toward you. Set the door aside

in a safe place.

CAUTION

Risk of equipment damage

Improperly inserting the battery may damage the battery connector in

the Telephony Gateway. Carefully follow the instructions in the next

step to avoid damage.

2

Hold the battery pack so that the guides on the battery align with the slots

on the Telephony Gateway and slide the battery into the bay. The diagram

on the left shows the proper orientation.

Note

: Batteries will not insert completely into the Telephony Gateway if not

oriented correctly. The battery should slide into the bay without signiﬁcant

force. Line up the slots in the battery bay with the guides on the battery

and apply even pressure on both ends of the battery.

Touchstone TG862 Telephony Gateway User’s Guide

Safety

Getting

Started

Battery

Installation

Ethernet

Conﬁguration

Usage

Troubleshooting

Glossary

17

Battery

Pull Strap

Battery Guides

Battery Slots

WRONG

RIGHT

Latch End

Page 18 / 56

3

Push the battery pack into the bay until it latches into place.

If you are

taking the battery out of the Telephony Gateway, use the battery

pull strap to dislodge the battery.

Note

: The Telephony Gateway will not begin operating until you apply AC

power.

4

Replace the door. To do so, place the tabs of the battery door into the slot

inside the Telephony Gateway battery compartment. Rotate the door toward

the front of the Telephony Gateway until the latch snaps back into place.

Note

: Telephony Gateways use a Lithium-Ion battery pack. Please recycle

or dispose of the battery responsibly and in accordance with local ordi-

nances.

Touchstone TG862 Telephony Gateway User’s Guide

Safety

Getting

Started

Battery

Installation

Ethernet

Conﬁguration

Usage

Troubleshooting

Glossary

18

Battery

Compartment

Receiver

Slots

Hinge Tabs

Page 19 / 56

Installing and Connecting Your

Telephony Gateway

Before you start, make sure that:

•

You have contacted your cable company and veriﬁed that they provide data

and telephone service using standard DOCSIS technology.

•

You have all the

items you need

.

•

Cable, phone, and power outlets are available near the computer. If a cable

outlet is not conveniently located, your cable company can install a new one.

If you have ordered service, your cable company should conﬁgure the Telephony

Gateway automatically. You need only follow the instructions in this section to in-

stall and connect the Telephony Gateway.

CAUTION

Risk of equipment damage

Only qualiﬁed installation technicians should connect the Telephony

Gateway to house wiring. Incumbent telephone service must be physi-

cally disconnected at the outside interface box before making any

connections.

Touchstone TG862 Telephony Gateway User’s Guide

Safety

Getting

Started

Battery

Installation

Ethernet

Conﬁguration

Usage

Troubleshooting

Glossary

19

Page 20 / 56

Reset

USB

Telephone

Ethernet

10/100/1000

Cable

1/2

2

1

4

3

A

C

B

D

F

E

H

G

Power

Ethernet

DS

US

Online

WiFi

Secure

Tel 1

Battery

Tel 2

TG862

B

E

C

A

D

F

H

J

G

I

20

Safety

Getting

Started

Battery

Installation

Ethernet

Conﬁguration

Usage

Troubleshooting

Glossary

Touchstone TG862 Telephony Gateway User’s Guide

Front Panel

The front of the Telephony Gateway has the following indicators:

A

Battery

: indicates the battery status.

B

Tel 2

: indicates the status of telephone line 2.

C

Tel 1:

indicates the status of telephone line 1.

D

Secure

: indicates Wireless Protected Setup (WPS) is active.

E

WiFi

: indicates the status of the wireless LAN.

F

Ethernet

: indicates Ethernet connectivity between the Telephony Gateway

and computers.

G

Online

: indicates internet data transmission status.

H

US

: indicates upstream connectivity.

I

DS

: indicates downstream connectivity.

J

Power

: indicates whether AC power is available to the unit.

Rear Panel

The rear of the Telephony Gateway has the following connectors and controls:

A

WPS

button: begins associating the Telephony Gateway with a wireless de-

vice.

B

Reset

button: resets the Telephony Gateway as if you power cycled the unit.

Use a pointed non-metallic object to press this button.

C

USB:

USB host connector - future support for external USB devices

D

Telephone 1/2

: connector for the ﬁrst phone line (or both lines of a 2-line

phone).

E

Telephone 2

: connector for the second phone line.

F

Ethernet (1 - 4)

: connectors for use with a computer LAN port.

G

Cable

: connector for the coaxial cable.

H

Power

: connector for the power cord.

Rate

Popular Arris Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share