Page 46 / 56 Scroll up to view Page 41 - 45
Booting from Battery
The TG862 supports a “Boot from Battery” feature that allows the Telephony Gate-
way to begin service without AC power.
To start the TG862 from its battery, follow these steps:
1
If a battery is already installed in the Telephony Gateway, remove it.
2
Re-insert the battery into the Telephony Gateway (see
Battery Installation
and Removal
for details).
3
Press the
Reset
button; the Power light should turn on immediately.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
46
Page 47 / 56
Troubleshooting
The Telephony Gateway is plugged in, but the Power light is off.
Check all power connections. Is the power cord plugged in firmly at both
ends?
If you plugged the power cord into a power strip, make sure the strip is
switched on.
Avoid using an outlet controlled by a wall switch, if possible.
Finally, check the fuse or circuit breaker panel.
I’m not getting on the Internet (all connections).
It may take over 30 minutes to establish a connection the first time you
power up your Telephony Gateway, especially when many people are online.
Always leave your Telephony Gateway plugged into AC power and connected
to the cable system.
Check the front panel lights:
The
Power
and
Online
lights should be on.
If the
Power
light blinks for more than 30 minutes, call your cable
company for assistance.
Check your cable connections. Connectors should be tight. The
coax cable
should not be pinched, kinked, or bent sharply—any of these can cause a
break or short in the cable (you may have to replace the cable). If you have
one or more splitters between the Telephony Gateway and CATV outlet, re-
move the splitters and connect the Telephony Gateway directly to the out-
let.
Proceed to the Ethernet or wireless solutions (next page) if necessary.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
47
Page 48 / 56
I’m not getting on the Internet. (Ethernet)
If you are using a hub, is the hub turned on?
Are you using the right type of
Ethernet
cable? Use the supplied cable for di-
rect connection to a computer; use a cross-over cable for connection to a
hub.
Press the
Reset
button on the back of the Telephony Gateway.
A misconfiguration could lock out all access to the Telephony Gateway router.
If you think this has happened, see
Resetting the Router to Factory Defaults
.
I’m not getting on the Internet. (Wireless)
Check the indicator lights (see
Using the Telephony Gateway
) — the WiFi
light should be on.
Does your connection utility discover your wireless LAN? If you turned off
“Broadcast SSID” you need to manually enter the name of your wireless LAN
in the connection utility.
Change your security mode to “WEP” or “disabled”. If you use “disabled,”
enable one of the other security modes as soon as you find the problem.
A misconfiguration could lock out all access to the Telephony Gateway router.
If you think this has happened, see
Resetting the Router to Factory Defaults
.
My wireless Internet connection stops working sometimes.
This is usually caused by interference — two common sources are 2.4GHz
“remote” telephones and microwave ovens. If you cannot remove the inter-
fering product, try using a different channel or setting Protected Mode.
I can get on the Internet, but everything is slow.
If the Web site you are visiting is very popular, that site may be having trou-
ble servicing all the requests. If other sites download quickly, wait for a few
minutes and try again. Usage during peak hours may also affect the connec-
tion speed.
Other communications on the LAN, or interference with wireless connec-
tions, may slow down your connection.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
48
Page 49 / 56
I don’t have dial tone when I pick up my phone, why?
In order for telephone service to be functional on the Telephony Gateway,
telephone service must have been purchased from the service provider and
configured on your Telephony Gateway. The following steps should help in
identifying the source of the problem.
1
Is the Power LED lit?
If not, check to make sure the Telephony Gateway is plugged in
and the outlet has power.
If the LED is lit, go to the next step.
2
Is the Online LED lit?
If not, check the coax connection at the Telephony Gateway and
the wall. Ensure they are connected and tight. If they are and
you do not have dial tone, contact your service provider.
If the Online LED is lit, go to the next step.
3
Is the Telephone (Tele 1 or Tel 2) LED lit?
If not, phone service has not been set up on that line. Contact
your service provider.
If it is blinking, there is a phone off hook somewhere in the
house. Find that phone and hang it up.
If it is lit, go to the next step.
4
Is the phone plugged directly into the Telephony Gateway?
Make sure the phone is plugged into the port on the back of the
Telephony Gateway labeled “Telephone 1/2” for line 1, and “Tele-
phone 2” for line 2.
If so, try a different phone. Make sure the new phone is a work-
ing phone.
If a known good phone is used and you still don’t have dial tone,
try a different phone cable. If a new phone and cable do not re-
store dial tone, call your service provider.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
49
Page 50 / 56
5
Is the Telephony Gateway plugged into a wall outlet?
If so, unplug the phone connector at the back of the Telephony
Gateway and plug in a known working phone. If you now have
dial tone, the problem is with the house wiring. Contact your
cable company or a qualified wiring technician to correct the
house wiring. If you still do not have dial tone, contact your serv-
ice provider.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Battery
Installation
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
50

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top