1. Home
    2. /
  2. Manuals
    3. /
  3. Arris
    4. /
  4. NVG599
    5. /
  5. 8
Page 36 / 50 Scroll up to view Page 31 - 35
Administrator’s Handbook
36
Loss of Signal
The absence of any signal for any reason, such as a disconnected cable or loss of
power.
Loss of Frame
A signal is detected but the device cannot sync with signal because of mismatched
protocols, wrong ISP connection configuration, or faulty cable.
FEC Errors
Forwarded Error Correction errors. Count of received errored packets that were fixed
successfully without a retry.
CRC Errors
Number of times data packets have had to be resent because of errors in transmission
or reception.
Ethernet Statistics (Ethernet WAN)
Line State
Up
or
Down
Current Speed
Line speed
Current Duplex
Full- or half-duplex
Receive Packets
Number of packets received
Transmit Packets
Number of packets sent
Receive Bytes
Number of bytes received
Transmit Bytes
Number of bytes sent
Receive Unicast
Receive Unicast statistics
Transmit Unicast
Transmit Unicast statistics
Receive Multicast
Receive Multicast statistics
Transmit Multicast
Transmit Multicast statistics
Receive Drops
Received packets dropped
Transmit Drops
Sent packets dropped
Receive Errors
Count of received errored packets that were fixed successfully without a retry.
Transmit Errors
Number of times data packets have had to be resent due to errors in transmission.
Collisions
Count of packet collisions.
Aggregated Information
Bonded Downstream Rate
The bonded channel receive rate.
Bonded Upstream Rate
The bonded channel transmit rate.
IPv6
Status
May be
Enabled
or
Unavailable
.
Global Unicast IPv6 Address
The public IPv6 address of your device, whether dynamically or statically assigned.
Border Relay IPv4 Address
The public IPv4 address of your device.
IPv4 Statistics
Transmit Packets
IPv4 packets transmitted.
Transmit Errors
Errors on IPv4 packets transmitted.
Transmit Discards
IPv4 packets dropped.
IPv6 Statistics
Transmit Packets
IPv6 packets transmitted.
Transmit Errors
Errors on IPv6 packets transmitted.
Transmit Discards
IPv6 packets dropped.
Page 37 / 50
37
Link:
Configure
When you click the
Configure
link, the Broadband
Configure
screen appears. Here you can reconfigure your
type of broadband connection should it change in the future.
±
Broadband Source Override
- Auto (automatically detected), DSL - Line 1, DSL - Line 2, DSL - Line 1 / Line -2
(Bonded), or Ethernet WAN.
If you switch from DSL to Ethernet or from Ethernet to DSL, the device will prcoceed to reconnect as in its ini-
tial connection to the Internet, as described earlier. See
“Accessing the Web Management Interface” on
page 21
.
±
The WAN connection is automatically configured. However, you can adjust the
Maximum allowable MTU
(maximum transmittable unit) value, if your service provider suggests it. The default 1500 is the maximum
value, but some services require other values (1492 is common).
If you make any change here, click the
Save
button.
Page 38 / 50
Administrator’s Handbook
38
Link:
IGMP Stats
When you click the
IGMP Stats
link, the
IGMP Stats
screen appears. The IGMP statistics screen reports IGMP
proxy groups and multicast forwarding information. It also displays a packet counter.
Page 39 / 50
39
Home Network Tab
When you click the
Home Network
tab, the Home Network Status page appears.
The Home Network Status page displays information
about the NVG599 device’s local area network.
If you click the
Run Congestion Detection
button, the
device will generate statistics for each of the 11
channels available, displaying:
±
Channel number
±
AP (access point) count
±
Congestion score (1 - 10) - Note that higher val-
ues mean lower congestion.
The wireless congestion feature provides simple data to
the user to show the level of network congestion in
each wireless channel.
This data can be used to
determine router placement or to determine which
channels to avoid.
The display tells the user how many access points (APs)
are active within each channel, and provides a score of
1 - 10 to indicate how clear the channel is.
A higher
score indicates less congestion in a channel; thus, a 10
indicates a channel extremely clear of wireless traffic
and noise.
Alternatively, a score of 1 indicates more
severe congestion in a channel.
You can clear the current statistics information by
clicking the
Clear Statistics
button.
Page 40 / 50
Administrator’s Handbook
40
Home Network Status
Device IPv4 Address
The NVG599 device’s own IP address on the network.
DHCP Netmask
The device’s own netmask on the network.
DHCPv4 Start Address
The starting IP address of the DHCP range served by the device.
DHCPv4 End Address
The ending IP address of the DHCP range served by the device.
DHCP Leases Available
The number of IP addresses of the DHCP range available to be served by the device.
DHCP Leases Allocated
The number of IP addresses of the DHCP range currently being served by the device.
DHCP Primary Pool
Source pool of the IP addresses served by the NVG599 device, Public or Private.
IPv6
Status
May be
Enabled
or
Unavailable
.
Global IPv6 Address
The public IPv6 address of your device, whether dynamically or statically assigned.
Link-local IPv6 Address
The private IPv6 address of your device, whether dynamically or statically assigned.
Router Advertisement Prefix
The IPv6 prefix to include in router advertisements.
IPv6 Delegated LAN Prefix
The IPv6 network address prefix that identifies the NVG599 network.
IPv4 Statistics
Transmit Packets
IPv4 packets transmitted.
Transmit Errors
Errors on IPv4 packets transmitted.
Transmit Discards
IPv4 packets dropped.
IPv6 Statistics
Transmit Packets
IPv6 packets transmitted.
Transmit Errors
Errors on IPv6 packets transmitted.
Transmit Discards
IPv6 packets dropped.
WiFi Status
WiFi Radio Status
Status of the Wi-Fi radio:
Enabled
or
Disabled
.
Mode
2.4 Ghz radio may be 802.11
B
only, 802.11
G
only, 802.11
N
only, 802.11
B/G
or 802.11
B/G/N
.
5.0 Ghz radio may be 802.11
A
, 802.11
AC
only, 802.11
N
only or 802.11
AC
(i.e.
802.11
N/AC
) as well.
Bandwidth
The capacity of the wireless LAN to carry traffic in megahertz.
Current Radio Channel
The radio channel that your Wi-Fi network is broadcasting on.
Radio Channel Selection
May be set to
automatic
or manually selected.
MAC Address Filtering
May be either
On
or
Off
. If On, you can accept or block client devices from your WLAN
based on their MAC address.
Power Level
May be adjusted up to 100%, lower if multiple wireless access points are in use, and
might interfere with each other.
WiFi MAC Address
Shows the information of the MAC address of the wireless subsystem.
User SSID
May be either
On
or
Off
for either frequency.
Guest SSID
May be either
On
or
Off
for the 2.4 Ghz radio only.
Network Name (SSID)
The name or ID that is displayed to a client scan. The default SSID for the NVG599 is
att
xxx
where
xxx
is the last 3 digits of the serial number located on the side of the
NVG599 device.
Hide SSID
May be either
On
or
Off
. If
On
, your SSID will not appear in a client scan.

Rate

3.5 / 5 based on 2 votes.

Popular Arris Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top