1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 173
Page 861 / 998 Scroll up to view Page 856 - 860
PPPoE command reference
PPPoE
8-91
iMG/RG Software Reference Manual (ADSL Port)
Options
The following table gives the range of values for each optionthat can be specified with this
command and a default value (if applicable).
Example
--> pppoe set transport pppoe2 lcpechoevery 0
See also
PPPOE SHOW TRANSPORT
PPPOE LIST TRANSPORTS
8.7.4.1.29 PPPOE SET TRANSPORT LCPMAXCONF
Syntax
PPOE SET TRANSPORT
{<name>|<number
>} LCPMAXCONF
<lcp max config-
ure>
Description
This command sets the
Link Control Protocol
(LCP) maximum configure number for an
existing PPPoE transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoE transport. To display transport names,
use the
PPPOE LIST TRANSPORTS
command.
N/A
number
An existing PPPoE transport. To display transport num-
bers, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
interval
The length of time (in seconds) between LCP echo
request frames being sent. If you do not want echo
request frames to be sent, specify ‘0’ as the interval.
10 seconds
Option
Description
Default Value
name
An existing PPPoE transport. To display transport
names, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
number
An existing PPPoE transport. To display transport num-
bers, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
Page 862 / 998
PPPoE
PPPoE command reference
iMG/RG Software Reference Manual (ADSL Port)
8-92
Example
--> pppoe set transport pppoe1 lcpmaxconf 20
See also
PPPOE SHOW TRANSPORT
PPPOE LIST TRANSPORTS
8.7.4.1.30 PPPOE SET TRANSPORT LCPMAXFAIL
Syntax
PPPOE SET TRANSPORT
{<name>|<number>}
LCPMAXFAIL
<lcp max
fail>
Description
This command sets the
Link Control Protocol
(LCP) maximum fail number for an existing
PPPoE transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoe set transport pppoe1 lcpmaxfail 20
See also
PPPOE SHOW TRANSPORT
PPPOE LIST TRANSPORTS
8.7.4.1.31 PPPOE SET TRANSPORT LCPMAXTERM
Syntax
PPPOE SET TRANSPORT
{<name>|<number
>} LCPMAXTERM
<lcp max termi-
nate>
lcp max configure
Link Control Protocol
: the maximum number of configures
that can be transmitted without reply before assuming
that the destination address is unable to respond. The
LCPmaxconf can be any positive value.
10
Option
Description
Default Value
name
An existing PPPoE transport. To display transport
names, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
number
An existing PPPoE transport. To display transport num-
bers, use
THE PPPOE LIST TRANSPORTS
com-
mand.
N/A
lcp max fail
Link Control Protocol
: the maximum number of consecu-
tive negative acknowledgements (indicating that the
information received contains errors) that can be trans-
mitted before assuming that parameter negotiation is
not converging. The LCPmaxfail can be any positive
value.
5
Page 863 / 998
PPPoE command reference
PPPoE
8-93
iMG/RG Software Reference Manual (ADSL Port)
Description
This command sets the
Link Control Protocol
(LCP) maximum terminate number for an
existing PPPoE transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoe set transport pppoe1 lcpmaxterm 20
See also
PPPOE SHOW TRANSPORT
PPPOE LIST TRANSPORTS
8.7.4.1.32 PPPOE SET TRANSPORT LOCALIP
Syntax
PPPOE SET TRANSPORT {<name>|<number>} LOCALIP <ip-address>
Description
This command tells the PPP process the local IP address to be associated with the client-
end of an interface. This enables remote users to have dialin access via the channel(s) that
the interface is attached to.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoE transport. To display transport
names, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
number
An existing PPPoE transport. To display transport num-
bers, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
lcp max term
Link Control Protocol
: the maximum number of consecu-
tive Terminate Requests that will be sent without reply
before assuming that the destination address is unable
to respond. The LCPfailterm can be any positive value.
2
Option
Description
Default Value
name
An existing PPPoE transport. To display transport names,
use the
PPPOE LIST TRANSPORTS
command.
N/A
number
An existing PPPoE transport. To display transport num-
bers, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
Page 864 / 998
PPPoE
PPPoE command reference
iMG/RG Software Reference Manual (ADSL Port)
8-94
Example
--> pppoe set transport pppoe1 localip 192.168.103.2
See also
PPPOE SHOW TRANSPORT
PPPOE LIST TRANSPORTS
PPPOE SET TRANSPORT REMOTEIP
8.7.4.1.33 PPPOE SET TRANSPORT MANUALCONNECT
Syntax
PPPOE SET TRANSPORT
{<name>|<number>}
MANUALCONNECT
{ENABLED|DISABLED}
Description
This command enales/disables the manual connect option for a givien PPPoE transport.
In this mode, the connection to the network is initiated manually through a GUI request
of a CLI command and by default, terminates only when done so explicitly by a user, dur
ot power loss, or when the connection is lost.
When the manual connect option is enabled, the autoconnect feature of the device is
automatically disabled.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoe set transport pppoe1 manualconnect enabled
Description
PPPOE LIST TRANSPORTS
PPOE SET TRANSPORT LCPECHOEVERY
ip-address
The IP address of the local ‘client-end’ of an interface dis-
played in the following format: 111.222.254.4
0.0.0.0
Option
Description
Default Value
name
An existing PPPoE transport. To display transport names,
use the
PPPOE LIST TRANSPORTS
command.
N/A
number
An existing PPPoE transport. To display transport num-
bers, use the
PPPOE LIST TRANSPORTS
com-
mand.
N/A
enabled
Enable the “manualconnect” option
Disabled
disabled
Disable the “manualconnect” option
Page 865 / 998
PPPoE command reference
PPPoE
8-95
iMG/RG Software Reference Manual (ADSL Port)
8.7.4.1.34 PPPOE SET TRANSPORT MAXREAUTHATTEMPTS
Syntax
PPPOE SET TRANSPORT
{<name>|<number>}
MAXREAUTHATTEMPTS
<max reau-
thattempts>
Description
This command is used to specify the number of re-authentication attempts in case of
authentication failure. After the specified number of re-authentication attempts fail, there
would be no more configure requests from PPPoE transports until the unsername and/or
password are reset.
A zero (default) value specifies inifinate connection attempts.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoe set transport pppoe3 maxreauthattempts 10
See also
PPPOE SET TRANSPORT REAUTHTIMER
8.7.4.1.35 PPPOE SET TRANSPORT MBS
Syntax
PPPOE SET TRANSPORT {<name>|<number>} MBS <max burst size>
Description
This command sets the maximum burst size (MBS) for an existing PPPoE transport that
performs dialout over PVC.
Description
This command is only valid if you set VBR or VBR RT as the QoS Class using the
PPPOE
SET TRANSPORT QUOSCLASS
command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoE transport. To display transport
names, use the pppoe list transports command.
N/A
number
An existing PPPoE transport. To display transport
numbers, use the pppoe list transports command.
N/A
maxreauthattempts
A number tht specifies the maximum re-authentica-
tion requests that can be made
0

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top