Allied-Telesis AT-iMG624A Router Manual PDF (Setup & Configuration Guide)

Page 786 / 998 Scroll up to view Page 781 - 785

Port a1

Port a1 command reference

iMG/RG Software Reference Manual (ADSL Port)

8-16

BisATxEndBin

BisBTxEndBin

BisMTxEndBin

ONLY Group B devices

Configures Tx End Bin for Bis/Bis+

31 (BisA)

63 (BisM/B)

BisATxStartBin

BisBTxStartBin

BisMTxStartBin

ONLY Group B devices

Configures Rx Start Bin for Bis/Bis+

6 (BisA/M)

64 (BisB)

BisA_PMmode

BisB_PMmode

BisM_PMmode

ONLY Group B devices

Parameter controls which Power Management

modes are to be supported on Bis/Bis+

Possible values are:

L2L3NotAllowed, L3NotAllowed, L2L3Allowed

L2L3Allowed

BisA_REIN

BisB_REIN

BisM_REIN

ONLY Group B devices

Possible values are:

Per_CO_Request, 60pps,120pps

60pps

BisA_SRA

BisB_SRA

BisM_SRA

ONLY Group B devices

Enables/Disables the Downstream SRA feature

on Bis/Bis+

Possible values are:

Disable, Enable

Enable

BitSwap

Group A and Group C devices

Enable/Disable downstream bit swapping.

Possible values are:

enable, disable

Enable

BitSwapUp

Group A and Group C devices

To Enable/Disable Downstream BitSwap for

AnnexA/B

Enable

TABLE 8-2

Options for ADSL Port Attributes (Continued)

Option

Description

Default Value

Page 787 / 998

Port a1 command reference

Port a1

8-17

iMG/RG Software Reference Manual (ADSL Port)

Capability

Group A and Group C devices

This parameter controls if the CPE will attempt

to startup using alternate standards, dependent

upon CO capability.

Possible values are for AnnexA:

GDMT, BIS, BIS+, BIS+/GDMT, BIS+/T1413, BIS+/

BIS, BIS+/BIS/T1413, BIS+/BIS/GDMT, A-ALL,

MBIS, MBIS+, MBIS+/MBIS, MA-ALL, BIS+/BIS/A/

MULTIMODE, Disable.

Possible values are for AnnexB:

BIS+/BIS/B, Disable

MA-ALL (AnnexA)

ClockType

Configures the Clock

Type to Crystal/Oscillator

Crystal

CodeType

Group A and Group C devices

CodingGain

Group A and Group C devices

Coding gain is the reduction in transmit power

realized by implementing trellis/RS coding tech-

niques. Automatic coding gain selection is recom-

mended for automatic bit allocation depending

upon line conditions. Otherwise, requested cod-

ing gain is selectable from 0 dB to 7 dB in 1 dB

increments.

N/A

CabinetMode

Group A and Group C devices

DSPTrace

ONLY Group B devices

This option allows to start logging of the DSP

Trace to a file.

Possible values are:

StopLogging, StartLogging

StopLogging

TABLE 8-2

Options for ADSL Port Attributes (Continued)

Option

Description

Default Value

Page 788 / 998

Port a1

Port a1 command reference

iMG/RG Software Reference Manual (ADSL Port)

8-18

Defaults

Group B devices:

Option to assign defaults to all the parameters.

Possible values are:

None, All

Group A and C devices:

Set default parameters based on the standard

selected.

Possible values are:

None, ADSL2, ADSL2PlusAuto, ADSL2PlusOnly,

AnnexA, AnnexM2,

AnnexM2PlusAutoAnnexM2PlusOnly, AnnexB,

AnnexB2, AnnexB2PlusAuto, AnnexB2PlusOnly

None

DetectNoise

Enables and Disables Detect Noise

Disable

DyingGasp

Enable or Disable the DyingGasp support

Disable

EcFdmMode

Group A and Group C devices

Depending upon which mode is required by your

service provider, overlap of bins (Echo Cancella-

tion) may be selected by the value EC. Likewise, if

you should deploy no overlap (Frequency Divi-

sion Multiplexing) the value FDM may be

selected.

Possible values are:

EC,FDM

FDM

FastRetrain

Group A and Group C devices

Configures Fast Retrain on the Line for AnnexA/

B.

Possible values are:

Enable, Disable

Disable

TABLE 8-2

Options for ADSL Port Attributes (Continued)

Option

Description

Default Value

Page 789 / 998

Port a1 command reference

Port a1

8-19

iMG/RG Software Reference Manual (ADSL Port)

FramerType

Group A and Group C devices

There are two types of framing defined per

T1.413: full overhead and reduced overhead. Each

type has 2 versions thus resulting in four framing

structures referred to as 0, 1, 2, and 3. These

framing structures are described in Table 4 of

T1.413. Framing type 3 should be used for single

latency applications. When using dual latency,

framing type 2 should be selected.

Possible values are:

Type0, Type1, Type2, Type3,Type3ET for Data

boost

Type3ET

GenericTrace

ONLY Group B devices

Configure the GenX trace( SAS/DSP).

Possible values are:

Disable, EnableAll, DSP, SAS

DSP

HappyMode

Group A and Group C devices

Possible values are:

Disable, Enable

Enable

HostControl

Enable/Disable Flag to control host.

Possible values are:

Disable, Enable

Enable

LoopbackTest

ONLY Group B devices

Parameter to set and test the Loopback assigned.

Possible values are:

DAC/ADC Lpbk MTS, TX/RX Baseline MTS,

Hybrid Resp Lpbk MTS, TX Filter Lpbk MTS, RX

Filter Lpbk MTS, MTPR Lpbk MTS,

Quiet Line PSD

MTS

MaxBitsPerBin

Group A and Group C devices

Set the maximum number of receive bits per bin

can be selected.

Possible values are:

0 to 15

15

TABLE 8-2

Options for ADSL Port Attributes (Continued)

Option

Description

Default Value

Page 790 / 998

Port a1

Port a1 command reference

iMG/RG Software Reference Manual (ADSL Port)

8-20

MaxDownRate

Group A and Group C devices

Set the maximum downstream rate in bits per

seconds

511

MaxInterleaveD

Group A and Group C devices

Sets the Max interleaved Depth

Possible values are:

64, 128, 256, 511

511

MaxRSMemory

ONLY Group B devices

Configures the Size of RS Memory

Possible values are:

16, 24, 32, 48

32

MaxSNRMargin

Group A and Group C devices

SNR Margin

Possible values are:

Enable, Disable

Disable

MemorizedConnec-

tion

Group A and Group C devices

Possible values are:

Enable, Disable

Disable

NTRMode

Group A and Group C devices

PMmode

Possible values are:

L2L3NotAllowed, L3NotAllowed, L2L3Allowed

L2L3Allowed

PSDMask

Group A and Group C devices

PhysicalPort

Physical port of the PCU that is to be used for

Data transfer.

0

Profile

Configures the Profile to be used

Possible values are:

MAIN, BT, SPAIN, SBC, COVAD, BRAZIL, MII,

KT, TELSTRA, XR, HAN, FRANCE, FINLAND

a

,

FASTWEB, RESERVED

MAIN

TABLE 8-2

Options for ADSL Port Attributes (Continued)

Option

Description

Default Value

Rate

Popular Allied-Telesis Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share