1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 127
Page 631 / 998 Scroll up to view Page 626 - 630
VoIP ADMIN Command Reference
VoIP phone ports
6-67
iMG/RG Software Reference Manual (Voice Service)
Note:
Frequency in Hz:f1xf2 means f1 is modulated by f2
Note:
f1+f2 is the juxtaposition of two frequencies f1 and f2 without modulation.
Note:
Cadence in seconds:ON – OFF
6.3.1.6 Port enable/disable
It's possible to temporarily disable a port by using the VOIP EP ANALOGUE DISABLE command.
Any call originated from, or sent to, a user attached to a disabled access port is discharged.
When a port is disabled, each user added to the port starts to un-register from the Location Server (SIP
signal-
ling
protocol).
To change the port status from disabled to enabled use the VOIP EP ANALOGUE ENABLE command.
As soon the port is enabled all the users attached to the port automatically restart the process of registration
with the location server or gatekeeper.
To show the users attached to a port (and their SIP registration status), use the VOIP EP ANALOGUE SHOW
command.
6.3.2
VoIP ADMIN Command Reference
6.3.2.1 VoIP ADMIN commands
VoIP ADMIN commands set the service profile to be compliant with specific customer requirement and assign
main parameter concerning network administration.
Singapore
425
Continuous
425
750 - 750
425x24
400 - 200 -
400 - 2000
Spain
425
Continuous
425
200 - 200
425
1500 - 3000
Sweden
425
Continuous
425
250 - 250
425
1000 - 5000
Turkey
450
Continuous
450
500 - 500
450
2000 - 4000
United Kingdom
350+440
Continuous
400
375 - 375
400+450
400 - 200 -
400 - 2000
United States
350+440
Continuous
480+620
500 - 500
440+480
2000 - 4000
TABLE 6-12
Country-specific Telecom tones (Continued)
Page 632 / 998
VoIP phone ports
VoIP ADMIN Command Reference
iMG/RG Software Reference Manual (Voice Service)
6-68
TABLE 6-13
Commands for VoIP Admin
6.3.2.1.1 VOIP SHOW
Syntax
VOIP SHOW
Description
This command shows the configured VoIP protocol.
Example
--> voip show
Gateway base protocol: SIP
----------------------------------------------------
Endpoints:
1
Users:
1
FDB items:
-
6.3.2.1.2 VOIP ADMIN ENABLE PROFILE
Syntax
VOIP ADMIN ENABLE PROFILE <profilename>
Description
It enables a specific customer profile.
Commands
Fiber
A
Fiber
B
Fiber
C
Fiber
D
Fiber
E
Modular
ADSL
A
ADSL
B
ADSL
C
VOIP SHOW
X
X
X
X
X
X
X
X
X
VOIP ADMIN ENABLE PROFILE
X
X
X
X
X
X
X
X
X
VOIP ADMIN ENABLE RFC3660-DIGIT-INPUT-TIMER
X
X
X
X
X
X
X
X
X
VOIP ADMIN DISABLE PROFILE
X
X
X
X
X
X
X
X
X
VOIP ADMIN DISABLE RFC3660-DIGIT-INPUT-TIMER
X
X
X
X
X
X
X
X
X
VOIP ADMIN PREFIX-REPLACEMENT ADD
X
X
X
X
X
X
X
X
X
VOIP ADMIN PREFIX-REPLACEMENT CREATE
X
X
X
X
X
X
X
X
X
VOIP ADMIN PREFIX-REPLACEMENT DELETE
X
X
X
X
X
X
X
X
X
VOIP ADMIN PREFIX-REPLACEMENT LIST
X
X
X
X
X
X
X
X
X
VOIP ADMIN PREFIX-REPLACEMENT REMOVE
X
X
X
X
X
X
X
X
X
VOIP ADMIN PREFIX-REPLACEMENT SHOW
X
X
X
X
X
X
X
X
X
VOIP ADMIN SET E164-COUNTRY-CODE
X
X
X
X
X
X
X
X
X
VOIP ADMIN SET INTERNATIONAL-CALL-PREFIX
X
X
X
X
X
X
X
X
X
VOIP ADMIN SHOW
X
X
X
X
X
X
X
X
X
Page 633 / 998
VoIP ADMIN Command Reference
VoIP phone ports
6-69
iMG/RG Software Reference Manual (Voice Service)
Note:
The command is available only for the
SIP protocol
Note:
The command MUST be executed before users are provisioned.
Note:
Enabling a specific profile re-sets the numbering plan parameters to default.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip admin enable profile sonus
6.3.2.1.3 VOIP ADMIN ENABLE RFC3660-DIGIT-INPUT-TIMER
Syntax
VOIP ADMIN ENABLE RFC3660-DIGIT-INPUT-TIMER
Description
This command enables the management of critical and partial inter-digit times as specified
in RFC3660.
Example
--> voip admin enable rfc3660-digit-input-timer
See also
VOIP EP SET IDT-CRITICAL
VOIP EP SET IDT-PARTIAL
6.3.2.1.4 VOIP ADMIN DISABLE PROFILE
Syntax
VOIP ADMIN DISABLE PROFILE
Description
This command disables the specific customer profile that was in use; standard behaviour
is then assumed.
Option
Description
Default Value
profilename
The profile identifies a specific behaviour
At the moment, the following profile have been devel-
oped:
•
ntt-cw
NTT-Comware profile
•
sonus
Sonus solution for Voice over IP service pro-
vided by AT&T
•
lucent
Lucent SIP proxy profile
•
Broadsoft. When activated, the broadsoft profile has
only one effect: If a SIP Info request is encoded to
send a flash-hook event, the content-type header will
be set to 'application/broadsoft' instead of 'applica-
tion/dtmf-relay'
No profile is enabled by default.
N/A
Page 634 / 998
VoIP phone ports
VoIP ADMIN Command Reference
iMG/RG Software Reference Manual (Voice Service)
6-70
Note:
This command is not available once users have been provisioned.
Note:
Disabling a specific profile re-sets the numbering plan parameters to default.
Example
--> voip admin disable profile
6.3.2.1.5 VOIP ADMIN DISABLE RFC3660-DIGIT-INPUT-TIMER
Syntax
VOIP ADMIN DISABLE RFC3660-DIGIT-INPUT-TIMER
Description
This command disables the management of critical and partial inter-digit times as speci-
fied in RFC3660.
Example
--> voip admin disable rfc3660-digit-input-timer
6.3.2.1.6 VOIP ADMIN PREFIX-REPLACEMENT ADD
Syntax
VOIP ADMIN PREFIX-REPLACEMENT ADD <name> PORT <ep-name>
Description
This command adds the prefix-replacement rule to an already provisioned endpoint. The
prefix replacement rule must already have been created with the VOIP ADMIN PREFIX-
REPLACEMENT CREATE” command.
Options
The following table gives the range of values for each option which can be specified with
this command, and a default value (if applicable).
Example
--> voip admin prefix-replacement add pref001 port prt0
See also
VOIP ADMIN PREFIX-REPLACEMENT CREATE
VOIP ADMIN PREFIX-REPLACEMENT DELETE
VOIP ADMIN PREFIX-REPLACEMENT LIST
VOIP ADMIN PREFIX-REPLACEMENT REMOVE
VOIP ADMIN PREFIX-REPLACEMENT SHOW
6.3.2.1.7 VOIP ADMIN PREFIX-REPLACEMENT CREATE
Syntax
VOIP ADMIN PREFIX-REPLACEMENT CREATE <name> PREFIX <digit-
map> REPLACEMENT <digit>
Option
Description
Default Value
name
An existing prefix replacement rule created with the com-
mand “VOIP ADMIN PREFIX-REPLACEMENT CREATE”.
To display existing access port names, use the VOIP
ADMIN PREFIX-REPLACEMENT LIST command.
N/A
ep-name
An existing access port. To display existing access port
names, use the VOIP EP LIST command.
N/A
Page 635 / 998
VoIP ADMIN Command Reference
VoIP phone ports
6-71
iMG/RG Software Reference Manual (Voice Service)
Description
This command creates a prefix-replacement rule. When the rule is added to an endpoint,
if the PREFIX digit-map is matched, it is replaced by the REPLACEMENT digit(s).
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip admin prefix-replacement create prefix001 prefix *001 replacement 04411
See also
VOIP ADMIN PREFIX-REPLACEMENT ADD
VOIP ADMIN PREFIX-REPLACEMENT DELETE
VOIP ADMIN PREFIX-REPLACEMENT LIST
VOIP ADMIN PREFIX-REPLACEMENT REMOVE
VOIP ADMIN PREFIX-REPLACEMENT SHOW
6.3.2.1.8 VOIP ADMIN PREFIX-REPLACEMENT DELETE
Syntax
VOIP ADMIN PREFIX-REPLACEMENT DELETE <name>
Description
This command deletes a prefix-replacement rule.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Option
Description
Default Value
name
A string identifies the item, 1 to 16 characters in length.
Valid characters are any printable characters, except code
0x2E and 0x2F; digits cannot be used as first character and if
the space character is present, the string must be quoted..
N/A
digit-map
An expression string 1 to 16 characters in length. Valid
characters are digit and symbols ‘#’, ‘*’, ‘.’, ‘|’, ‘[’, ‘]’, ‘-‘.
The
service is disabled by default.
N/A
digits
A telephone number; 1 to 16 characters in length. Valid
characters are only numerical characters accepts the first
one that may assume the ‘+’ letter.
N/A
Option
Description
Default Value
name
An existing prefix replacement rule created with the
command “VOIP ADMIN PREFIX-REPLACEMENT
CREATE”. To display existing access port names, use
the VOIP ADMIN PREFIX-REPLACEMENT LIST
command.
N/A

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top