1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 129
Page 641 / 998 Scroll up to view Page 636 - 640
VoIP EP command reference
VoIP phone ports
6-77
iMG/RG Software Reference Manual (Voice Service)
6.3.3.1.1 VOIP EP CREATE
Syntax
VOIP EP ANALOGUE CREATE <name> TYPE <port-type> PHYSICAL-PORT <phy-port-id>
Description
This command adds a named access port and binds it to a physical access port.
If the physical resource is already assigned to another named port, an error is raised and
the command fails.
VOIP EP SET FLASHHOOK-TIME
X
X
X
X
X
X
X
X
X
VOIP EP SET HOLD-LOCAL-TONE-SERVICE
X
X
X
X
X
X
X
X
X
VOIP EP SET HOTLINE TIME-OUT
X
X
X
X
X
X
X
X
X
VOIP EP SET HOTLINE DISABLE
X
X
X
X
X
X
X
X
X
VOIP EP SET HOTLINE ENABLE
X
X
X
X
X
X
X
X
X
VOIP EP SET IDT-PARTIAL
X
X
X
X
X
X
X
X
X
VOIP EP SET INTERNAL-3-WAY-CALL
X
X
X
X
X
X
X
X
X
VOIP EP SET JITTERDELAY
X
X
X
X
X
X
X
X
X
VOIP EP SET JITTERMODE
X
X
X
X
X
X
X
X
X
VOIP EP SET LEC
4
4
4
3
4
3
4
3
3
VOIP EP SET OFFHOOK-TIME
X
X
X
X
X
X
X
X
X
VOIP EP SET ONHOOK-TIME
X
X
X
X
X
X
X
X
X
VOIP EP SET RXGAIN
X
X
X
X
X
X
X
X
X
VOIP EP SET STUTTER-DIAL-TONE
X
X
X
X
X
X
X
X
X
VOIP EP SET SUPPLEMENTARY-SERVICE-PREFIX
X
X
X
X
X
X
X
X
X
VOIP EP SET TXGAIN
X
X
X
X
X
X
X
X
X
VOIP EP SET UNREGISTERED-TONE
X
X
X
X
X
X
X
X
X
VOIP EP SET VAD
X
X
X
X
X
X
X
X
X
VOIP EP SHOW
X
X
X
X
X
X
X
X
X
Commands
Fiber
A
Fiber
B
Fiber
C
Fiber
D
Fiber
E
Modular
ADSL
A
ADSL
B
ADSL
C
Page 642 / 998
VoIP phone ports
VoIP EP command reference
iMG/RG Software Reference Manual (Voice Service)
6-78
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> voip ep analogue create prt0 type al-fxs-del physical-port tel1
See also
VOIP EP ANALOGUE DISABLE
VOIP EP ANALOGUE DELETE
VOIP EP ANALOGUE ENABLE
VOIP EP ANALOGUE LIST
VOIP EP ANALOGUE SET
VOIP EP ANALOGUE SHOW
6.3.3.1.2 VOIP EP DELETE
Syntax
VOIP EP ANALOGUE DELETE <name>
Description
This command deletes the named access port created previously using the VOIP EP
CREATE command.
Note:
Deleting an access port where one or more users are attached, causes a deregistration procedure to be
invoked for the users attached to the removed port.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue delete prt0
Option
Description
Default Value
name
An arbitrary name that identifies the access port. It can
be made up of one or more letters or a combination of
letters and digits, but it cannot start with a digit. The
maximum length is fixed to 16 characters.
N/A
port-type
This is
the user access typology served by the physical
port; the possible values depend on the model (analog
access or digital access).Valid values are al-fxs-del, al-fxs-
lc and al-fxo-del
N/A
phy-port-id
This is the physical port providing the access to VoIP
network.
“Port configuration”
N/A
Option
Description
Default Value
name
An existing access port. To display existing access port
names, use the VOIP EP LIST command.
N/A
Page 643 / 998
VoIP EP command reference
VoIP phone ports
6-79
iMG/RG Software Reference Manual (Voice Service)
See also
VOIP EP ANALOGUE CREATE
VOIP EP ANALOGUE DISABLE
VOIP EP ANALOGUE ENABLE
VOIP EP ANALOGUE LIST
VOIP EP ANALOGUE SET
VOIP EP ANALOGUE SHOW
6.3.3.1.3 VOIP EP DIAGNOSE
Syntax
VOIP EP ANALOGUE DIAGNOSE <name> {INTERNAL|EXTERNAL}
Description
This command starts GR.909 metallic loop tests on the selected analogue endpoint.
The support for metallic loop tests (internal and/or external) is available only on specific
iMG families.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue diagnose tel1 internal
End point:tel1, PHY tel1 is slic port #0
Calibration:
TG 1.1865V
RG 1.1865V
TR 2.7319V
:
:
Pass
:
Status :
Test
:
Criteria
:
Results
---------------------------------------------------------------------
PASS
: Battery input SWY
:
>=45V
: 52.718V
PASS
: Tip/Ground Voltage
:
abs <= 10V : -5.1268V
Option
Description
Default Value
name
An existing access port. To display existing access
port names, use the VOIP EP LIST command.
N/A
internal
In this case diagnostic tests apply only to internal
iMG circuitry.
N/A
external
In this case diagnostic tests apply only to the exter-
nal metallic loop and resistive loads connected to
the subscriber side.
N/A
Page 644 / 998
VoIP phone ports
VoIP EP command reference
iMG/RG Software Reference Manual (Voice Service)
6-80
PASS
: Ring/Ground Voltage
:
abs >= 38V : -46.888V
PASS
: Tip/Ring Voltage
: abs >= 38V
: -41.454V
PASS
: Tip/Ring Current
: abs <= 10mA : .12993mA
--------------------------------------------------------------------
PASS
: AC Ringing Voltage
:
>=53V
: 56.492Vrms
PASS
: AC Ringing Frequency
: 23Hz to 27Hz: 25Hz
--------------------------------------------------------------------
PASS
: Off Hook Sense
:
N/A
: No Problems
Found
Example
--> voip ep analogue diagnose tel1 external
End point:tel1, PHY tel1 is slic port #0
:
:
Pass
:
Status :
Test
:
Criteria
:
Results
--------------------------------------------------------------------
PASS
: Off Hook Sense
:
N/A
: No Problems
Found
--------------------------------------------------------------------
PASS
: HEMF
Tip/Ground
DC Voltage
: abs <= 135V : .43944V
PASS
: HEMF
Ring/Ground DC Voltage
: abs <= 135V : .43212V
PASS
: HEMF
Tip/Ring
DC Voltage
: abs <= 135V : -.014648V
PASS
: HEMF
Tip/Ground
AC Voltage
: abs <= 50V
: 0Vrms @
0Hz
PASS
: HEMF
Ring/Ground AC Voltage
: abs <= 50V
: 0Vrms @
0Hz
PASS
: HEMF
Tip/Ring
AC Voltage
: abs <= 50V
: 0Vrms @
0Hz
--------------------------------------------------------------------
PASS
: FEMF
Tip/Ground
DC Voltage
: abs <= 6V
: .43944V
PASS
: FEMF
Ring/Ground DC Voltage
: abs <= 6V
: .43212V
PASS
: FEMF
Tip/Ring
DC Voltage
: abs <= 6V
: -.014648V
PASS
: FEMF
Tip/Ground
AC Voltage
: abs <= 10V
: 0Vrms @
0Hz
PASS
: FEMF
Ring/Ground AC Voltage
: abs <= 10V
: 0Vrms @
0Hz
PASS
: FEMF
Tip/Ring
AC Voltage
: abs <= 10V
: 0Vrms @
0Hz
--------------------------------------------------------------------
Page 645 / 998
VoIP EP command reference
VoIP phone ports
6-81
iMG/RG Software Reference Manual (Voice Service)
PASS
: FEMF
Tip/Ring Current
:
Info Only
: .37332mA
---------------------------------------------------------------------
PASS
: Ringer Equivalance
:
N/A
: No Problems
Found
---------------------------------------------------------------------
PASS
: Resistive Fault (Tip/Ring)
:
R >= 150k
: 19969k
PASS
: Resistive Fault (Tip/Ground)
:
R >= 150k
:
2372k
PASS
: Resistive Fault (Ring/Ground)
:
R >= 150k
:
2553k
6.3.3.1.4 VOIP EP DISABLE
Syntax
VOIP EP ANALOGUE DISABLE <name>
Description
This command disables the physical port referred to by the named access port.
Use the VOIP EP SHOW command to retrieve the Operational Status of a specific port.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue disable prt0
See also
VOIP EP ANALOGUE CREATE
VOIP EP ANALOGUE DELETE
VOIP EP ANALOGUE ENABLE
VOIP EP ANALOGUE LIST
VOIP EP ANALOGUE SET
VOIP EP ANALOGUE SHOW
6.3.3.1.5 VOIP EP ENABLE
Syntax
VOIP EP ANALOGUE ENABLE <name>
Description
This command enables the physical port referred to by the named access port.
Use the VOIP EP SHOW command to retrieve the Operational Status of a specific port.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Option
Description
Default Value
name
An existing access port. To display existing access
port names, use the VOIP EP LIST command.
N/A

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top