Allied-Telesis AT-iMG624A Router Manual PDF (Setup & Configuration Guide)

Page 611 / 998 Scroll up to view Page 606 - 610

VoIP SIP Embeddedserver command reference

VoIP SIP

6-47

iMG/RG Software Reference Manual (Voice Service)

See also

VOIP SIP EMBEDDEDSERVER CREATE

VOIP SIP EMBEDDEDSERVER LIST

VOIP SIP EMBEDDEDSERVER SHOW

6.2.7.1.5 VOIP SIP EMBEDDEDSERVER SET PERMANENT-STORAGE

Syntax

VOIP SIP EMBEDDEDSERVER SET <name> PERMANENT-STORAGE

<ENABLED|DISABLED>

Description

This command enables or disables the permanent storage feature in the embedded-

server module.

Example

--> voip sip embedded set def-server permanent-storage enabled

See also

VOIP SIP EMBEDDEDSERVER CREATE

VOIP SIP EMBEDDEDSERVER LIST

VOIP SIP EMBEDDEDSERVER SHOW

6.2.7.1.6 VOIP SIP EMBEDDEDSERVER SHOW

Syntax

VOIP SIP EMBEDDEDSERVER SHOW

Description

This command shows the setting of the embedded-server module.

Example

-->

voip sip embeddedserver show def-server

Gateway - Embedded Proxy Servers:

-------------------------------------------------------------------

Operational Status:

in service

Emergency proxy mode:

redirect server

Domain:

See also

VOIP SIP EMBEDDEDSERVER CREATE

VOIP SIP EMBEDDEDSERVER LIST

VOIP SIP EMBEDDEDSERVER SET

Option

Description

Default Value

name

An arbitrary name that identifies the proxy server. The

name must not be present already.The name can be at

most 16 characters long; cannot start with a digit and

cannot contain dots '.' or slash symbols '/'.

N/A

Page 612 / 998

VoIP SIP

VoIP SIP User command reference

iMG/RG Software Reference Manual (Voice Service)

6-48

6.2.8

VoIP SIP User command reference

This section describes the commands available on the iMG intelligent Multiservice Gateway to enable, configure

and manage the

VoIP SIP User

module.

6.2.8.1 VoIP SIP User CLI commands

The table below lists the

VoIP SIP User

commands provided by the CLI:

TABLE 6-8

Commands for VoIP SIP User

6.2.8.1.1 VOIP SIP USER ADD

Syntax

VOIP SIP USER ADD <username> PORT <portname> [MASTER]

Description

This command attaches a user created with the command VOIP SIP USER CREATE to a

named port created with the command VOIP EP ANALOGUE CREATE.

As soon as this command is entered, the registration phase starts.

Note:

The system tries to register the user with the location server specified by the VOIP SIP

LOCATIONSERVER CREATE command. If no location servers are defined, the system tries to register

the user with the proxy server specified by the VOIP SIP PROXYSERVER CREATE command. If no

proxy servers are defined, registration phase is not performed until a location server or proxy server is

added to the SIP module.

To display the user's registration status and port association use the VOIP SIP USER

SHOW command.

The optional ‘master’ token may be used when multiple users are added to a single port.

Marking a user as ‘master’ indicates that this user should be specified in the From header

of outgoing SIP INVITE requests. Note that is no user is marked as ‘master’, then the

address of last user added to the port will be used in the From header of outgoing SIP

INVITE requests.

Commands

Fiber

A

Fiber

B

Fiber

C

Fiber

D

Fiber

E

Modular

ADSL

A

ADSL

B

ADSL

C

VOIP SIP USER ADD

X

VOIP SIP USER CREATE

X

VOIP SIP USER DELETE

X

VOIP SIP USER LIST

X

VOIP SIP USER REMOVE

X

VOIP SIP USER SHOW

X

Page 613 / 998

VoIP SIP User command reference

VoIP SIP

6-49

iMG/RG Software Reference Manual (Voice Service)

Options

The following table gives the range of values for each option that can be specified with

this command and a default value (if applicable).

Example

--> voip sip user add MrBrown port fxs0

See also

VOIP SIP USER ADD

VOIP SIP USER CREATE

VOIP SIP USER DELETE

VOIP SIP USER LIST

VOIP SIP USER REMOVE

VOIP SIP USER SHOW

VOIP EP LIST

6.2.8.1.2 VOIP SIP USER CREATE

Syntax

VOIP SIP USER CREATE <username> ADDRESS <digit-map> [AREA-

CODE <area-number>] [AUTHENTICATION <login:password>]

[DOMAIN <host >] [TRANSPORT <transport>] [PSEUDONYM <pseud-

onym>]

Description

This command creates a new entry in the users list. Each user must have a different

<username>. If the user already exists, an error message is raised.

This command is accepted only if the SIP module is already running. See the VOIP SIP

PROTOCOL ENABLE command to turn on the SIP module.

This command doesn’t bind the user to a physical access port. In order to inform the sys-

tem that the user is attached to a specific physical port, the VOIP SIP USER ADD com-

mand must be used.

Note:

If the DOMAIN parameter is not specified, the user domain is set equal to the location server address (if

defined) or proxy server address (if location server is not defined).

Options

The following table gives the range of values for each option that can be specified with

this command and a default value (if applicable).

Option

Description

Default Value

username

An existing user (it can be also the ID value associated

with the user name). To display the existing users, use the

VOIP SIP USER LIST command.

N/A

portname

An existing port. To display the existing ports, use the

VOIP EP LIST command.

N/A

Page 614 / 998

VoIP SIP

VoIP SIP User command reference

iMG/RG Software Reference Manual (Voice Service)

6-50

Example

--> voip sip user create MrBrown address 12345 domain 192.168.102.3 pseudonym

Charlie

See also

VOIP SIP USER ADD

VOIP SIP USER CREATE

VOIP SIP USER DELETE

VOIP SIP USER LIST

Option

Description

Default Value

username

An arbitrary name that identifies the user. The name

must not be present already. The username can be at

most 16 characters long; cannot start with a digit and

cannot contain dots '.' or slash symbols '/'.

N/A

digit-map

The phone number (E.164) used to reach the user.

The address can be 32 characters long.

N/A

area-number

The prefix number to be dialed before the destina-

tion number. Valid characters are only numerical

characters. The area number can be at most 10 digits

long.

empty

login

The user name used during the authentication phase.

The login can be at most 32 characters long. The

same rules defined for the username field also apply

here, except the login can start with a digit.

empty

password

The password used during the authentication phase.

The password can be at most 16 characters long. The

same rules defined for the username field also apply

here, except the password can start with a digit.

empty

host

The domain address in hostname format or IPv4 for-

mat. The domain can be at most 255 characters long.

empty

transport

The transport protocol used to contact the user.

Possible values are:

•

udp

•

tcp

udp

pseudonym

The pseudonym allows iMG SIP users to regis-

ter with a pseudonym (instead of their numeric

address). A user registered by pseudonym can

then be addressed either by pseudonym or

numeric address.

empty

Page 615 / 998

VoIP SIP User command reference

VoIP SIP

6-51

iMG/RG Software Reference Manual (Voice Service)

VOIP SIP USER REMOVE

VOIP SIP USER SHOW

6.2.8.1.3 VOIP SIP USER DELETE

Syntax

VOIP SIP USER DELETE <username>

Description

This command deletes a single user created using the VOIP SIP USER CREATE command.

To show the list of existing users, use the VOIP SIP USER LIST command.

As soon this command is entered, the de-registration phase starts (REGISTER request)

to the location server (registrar) removing the user from the user list on the server.

Options

The following table gives the range of values for each option that can be specified with

this command and a default value (if applicable).

Example

--> voip sip user delete MrBrown

See also

VOIP SIP USER ADD

VOIP SIP USER CREATE

VOIP SIP USER DELETE

VOIP SIP USER LIST

VOIP SIP USER REMOVE

VOIP SIP USER SHOW

6.2.8.1.4 VOIP SIP USER LIST

Syntax

VOIP SIP USER LIST

Description

This command lists information about users that were added using the VOIP SIP USER

CREATE command. The following information is displayed:

•

user ID numbers

•

user names

•

Area Codes

•

Addresses

Option

Description

Default Value

username

An existing user (it can also be the ID value associated

with the user name). To display the existing users, use the

VOIP SIP USER LIST command.

N/A

Rate

Popular Allied-Telesis Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share