22

Primary DNS

Please input the IP address of DNS server provided by your

service provider.

Secondary DNS

Please input the IP address of another DNS server provided by

your service provider, this is optional.

PPPoE (for DSL users)

For DSL users, your Internet type is either

Dynamic IP

or

PPPoE

. If you are not sure which one

you have, it is suggested to select

PPPoE

for your WAN type, and if you cannot connect to the

Internet after the Setup Wizard finished, go through the Setup Wizard again and

select

Dynamic IP

. Otherwise, you can call your ISP to confirm which Internet type you have.

Click on

PPPoE

for your WAN type. Enter your user name and password provided by your ISP.

Click

NEXT

.

Note:

Depending on the ISP, you may need to include the domain name with your username.

Example:

[email protected]

Parameter

Description

User Name

Please input user name assigned by your Internet service

provider here.

23

Password

Please input the password assigned by your Internet service

provider here.

DNS Address

Select the type of how you obtain IP address from your service

provider here. You can choose “Obtain an IP address

automatically”, or “Use the following IP address” (i.e. static IP

address).

Primary DNS

Please input the IP address of DNS server provided by your

service provider.

Secondary DNS

Please input the IP address of another DNS server provided by

your service provider, this is optional.

Service Name

Please give a name to this Internet service (this is optional).

MTU

Please input the MTU value of your network connection here. If

you don’t know, you can use default value.

Connection Type

Please select the connection type you wish to use. There are 3

options:

1) ‘Continuous’ - keep internet connection alive, do not

disconnect,

2) “Connect on Demand” - only connects to Internet when there’s

a connect attempt.

3) ‘Manual’ - only connects to Internet when ‘Connect’ button on

this page is pressed, and disconnects when ‘Disconnect button

is pressed.

Idle Time Out

Specify the time to shutdown internet connect after no internet

activity is detected by minute. This option is only available when

connection type is ‘Connect on Demand’.

Static IP

Click on Static IP if your ISP (Internet Service Provider) has provided you a set of IP addresses

for your Internet connection.

Enter the IP address, Subnet Mask, DNS addresses and Default Gateway provided by your ISP.

Note: You must use the addresses provided by your Internet service provider, wrong setting

value will cause connection problem.

24

PPTP

PPTP requires two kinds of setting: WAN interface setting (setup IP address) and PPTP setting

(PPTP user name and password).

Here we start from WAN interface setting:

Select the type of how you obtain IP address from your service provider here. You can choose

“Obtain an IP address automatically, or “Use the following IP address” (i.e. static IP address) for

IP and DNS address. WAN interface settings must be correctly set, or the Internet connection

will fail even those settings of PPTP settings are correct. Please contact your Internet service

provider if you don’t know what you should fill in these fields.

Now please go to PPTP settings section:

Parameter

Description

User Name

Please input user name assigned by your Internet service

provider here.

Password

Please input the password assigned by your Internet service

provider here.

PPTP Gateway

Please input the IP address of PPTP gateway assigned by your

Internet service provider here.

25

Connection

ID

Please input the connection ID here, this is optional and

you can leave it blank.

MTU

Please input the MTU value of your network connection here. If

you don’t know, you can use default value.

BEZEQ

-

ISRAEL

Setting item BEZEQ-ISRAEL is only required to check if you’re

using the service provided by BEZEQ network in Israel.

Connection

Type

Please select the connection type of Internet connection you

wish to use, please refer to last section for detailed descriptions.

Idle

Time

Out

Please input the idle time out of Internet connection you wish to

use, and refer to last section for detailed descriptions.

When you finish with all settings, please click NEXT.

L2TP

L2TP is another connection method for Internet. All required settings are same as PPTP

connection. Like PPTP, there are two types of required settings. Start from “WAN Interface

Settings”:

Select the type of how you obtain IP address from your service provider here. You can choose

“Obtain an IP address automatically, or “Use the following IP address” (i.e. static IP address) for

IP and DNS address. WAN interface settings must be correctly set, or the Internet connection

will fail even those settings of L2TP settings are correct. Please contact your Internet service

provider if you don’t know what you should fill in these fields.

Now please go to L2TP settings section:

26

Parameter

Description

User Name

Please input user name assigned by your Internet service

provider here.

Password

Please input the password assigned by your Internet service

provider here.

L2TP Gateway

Please input the IP address of L2TP gateway

assigned by your Internet service provider here.

MTU

Please input the MTU value of your network connection here. If

you don’t know, you can use default value.

Connection

Type

Please select the connection type of Internet connection you

wish to use, please refer to last section for detailed descriptions.

Idle

Time

Out

Please input the idle time out of Internet connection you wish to

use, and refer to last section for detailed descriptions.

When you finish with all settings, please click NEXT.

Telstra Big Pond

This setting only works when you are using Telstra Big Pond’s network service in Australia. You

need to input:

Parameter

Description

User Name

Please input user name assigned by Telstra.