TRENDnet TEW-455APBOv2 Router Manual PDF (Setup & Configuration Guide)

Given below is full router user manual of TRENDnet TEW-455APBOv2 router model. You can also download this manual in PDF Format to read later on your computer.

Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.

Page 1 / 17
Quick Installation Guide
TEW-455APBO
Page 2 / 17
English
1
Troubleshooting
13
1. Before You Start
1
2. Hardware Installation
3
3. Mounting
6
4. Connecting TRENDnet External Antenna
9
5. Configure the Access Point
10
Version 08.24.2009
Table of Contents
Page 3 / 17
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ÐÓÑÑÊÈÉ
1
1. Before You Start
?
Web Browser: Internet Explorer (5.5 or higher)
?
A computer with a network adapter properly installed
?
A network Switch or Hub with an available network LAN port
?
2 x RJ-45 network cable
?
RJ-45 Crimper
?
Wire stripper
?
Screwdriver
?
Waterproof tape
?
External Antenna with N-type Female connector (Optional)
?
TEW-ASAL1 (Optional)
Package Contents
?
T
?
CD-ROM (Utility &
)
?
Quick Installation Guide
?
AC
Power Adapter (48V DC)
?
Power Cord
?
Mounting Kit
?
Waterproof Kit*
?
Grounding wire
EW-455APBO
User’s Guide
System Requirements
Note:
The TEW-455APBO does not support IEEE 802.3af.
You must use the
special Power over Ethernet adapter that is supplied with the TEW-455APBO.
Page 4 / 17
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ÐÓÑÑÊÈÉ
2
Application
9dBi High Power Wireless
Outdoor PoE Access Point
(TEW-455APBO)
Cable
(TEW-ASAL1)
Cable/DSL
Modem
Cable/DSL Advanced
VPN Firewa l Router
(TW100-BRV304)
Workstations with
PCI Adapter
14 dBi Outdoor High-Gain
Directional Antenna
(TEW-OA14D)
16-Port 10/100Mbps
Fast Ethernet Switch
(TE100-S16R)
Internet
10/100Mbps
Multi-Port Print Server
(TE100-P21)
Printers
Workstations with
PCI Adapter
Notebook with
PC Card
PoE Power Adapter
PoE Power Adapter
*Check package contents for waterproof kit: (Ethernet Cable is not included)
Cable
Sealing Nut
Seal
Clamp Ring
Gasket
Screw Nut
Body
Plug
Gasket
Page 5 / 17
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ÐÓÑÑÊÈÉ
3
2. Hardware Installation
Note: Please connect the computer configuring the TEW-455APBO to the same
switch/hub.
4.
Use a wire stripper to strip off about 2 inches of
the cable sheath from one end of an Ethernet
cable. The recommended wire gauge is
24AWG.
3.
Connect the green grounding wire to a
grounding object. e.g. Earth Driven rod,
Grounded Electrical System, Building Frame.
1.
Remove the screw and washer from the
grounding hole using a screwdriver.
2.
Align one end of the grounding wire over the
hole.
Then connect the screw and washer back
in.
5.
Insert the seal into the rear of the clamp ring.
Then insert the gasket into the front end of the
clamp ring.
6.
Insert the body, the screw nut, the sealing nut
and clamp ring into the stripped end of the
cable.
12.0

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top