Page 16 / 156 Scroll up to view Page 11 - 15
Product overview
CellPipe 7130 RG features
1-6
Alcatel-Lucent
3FE-61830-AAAA-TCZZA
Edition 01
May 2008
Table 1-3 Rear panel items
Items
Usage
Line
Line RJ-11 port, used to connect the CellPipe 7130 RG to your ADSL (telephone)
line.
Reset
Reset the CellPipe 7130 RG to its factory default settings.
Insert a small, blunt object (for example, a paper clip) into the hole while the
CellPipe 7130 RG is powered on. Press and hold the Reset button for 5 s to reset the
CellPipe 7130 RG.
Ethernet
Ethernet RJ-45 port(s), used to connect the CellPipe 7130 RG to your PC(s).
Power on/ off
Power
Power connector, used to connect the CellPipe 7130 RG to your electrical outlet.
CellPipe 7130 RG features
Table 1-4 Feature support by model
Feature supported
1-port
Ethernet
(3Ae.A2010)
4-port
Ethernet
(3Ae.A2011)
4-port
wireless
(5Ae.A2010)
Various line modes
External PPPoE dial-up access
Internal PPPoE/PPPoA dial-up access
Leased line mode
PPP IP extension
1483B/1483R/MER access
Page 17 / 156
CellPipe 7130 RG features
Product overview
3FE-61830-AAAA-TCZZA
Alcatel-Lucent
1-7
Edition 01
May 2008
Feature supported
1-port
Ethernet
(3Ae.A2010)
4-port
Ethernet
(3Ae.A2011)
4-port
wireless
(5Ae.A2010)
Multiple PVCs (eight at most) and these PVCs can be isolated
from each other
Single PVC with multiple sessions
Multiple PVCs with multiple sessions
Binding of the ports and the PVCs
802.1Q and 802.1P protocols
DHCP server
NAT/NAPT
Static route
Firmware upgrade via Web, TFTP, FTP
Reset to factory default via hardware and software
DNS relay
Virtual server
DMZ functions
Two-level passwords and usernames
Web interface
Telnet CLI
System status display
PPP session PAP/CHAP
IP filter function
IP QoS function
Page 18 / 156
Product overview
CellPipe 7130 RG features
1-8
Alcatel-Lucent
3FE-61830-AAAA-TCZZA
Edition 01
May 2008
Feature supported
1-port
Ethernet
(3Ae.A2010)
4-port
Ethernet
(3Ae.A2011)
4-port
wireless
(5Ae.A2010)
Remote access control
Line connection status test
Remote management (Telnet, HTTP)
Configuration file backup and restore function
Ethernet supported such as Crossover Detection & Auto-
Correction and polarity correction
UPnP
SIP ALG
1 Ethernet port, 10/100Base-T Auto MDI/MDIX
4 Ethernet ports, 10/100Base-T Auto MDI/MDIX
24 Mb/s downstream 1 Mb/s upstream
Page 19 / 156
3FE-61830-AAAA-TCZZA
Alcatel-Lucent
2-1
Edition 01
May 2008
2
Hardware installation
Overview
Purpose
This chapter provides the instructions to install the CellPipe 7130 RG hardware.
Contents
This chapter covers the following topic:
To install the CellPipe 7130 RG
2-1
To install the CellPipe 7130 RG
Supplies
Twisted pair category 5 Ethernet cable
POTS splitter (Optional)
CellPipe 7130 RG
RJ-11 telephone cables
Power adapter
Page 20 / 156
Hardware installation
To install the CellPipe 7130 RG
2-2
Alcatel-Lucent
3FE-61830-AAAA-TCZZA
Edition 01
May 2008
Before you begin
Caution
Potential for equipment or personal harm
Before installing the CellPipe 7130 RG, ensure you have thoroughly read the Safety
precautions in chapter 1.
Procedure
1
Connect the splitter, if necessary. The splitter has three RJ-11 ports:
LINE - Connects to a telephone jack.
ROUTER - Connects to the DSL jack of the CellPipe 7130 RG.
PHONE - Connects to a telephone.
a.
Connect the incoming telephone line to the LINE port of the splitter with a telephone
cable; see Figure 2-1.
b.
Connect the DSL port of the CellPipe 7130 RG and the ROUTER port of the splitter
with a telephone cable.
c.
Connect the telephone to the PHONE port of the splitter with a telephone cable.
Figure 2-1 shows how to connect of the CellPipe 7130 RG, splitter, and telephone.

Rate

4.8 / 5 based on 4 votes.

Popular Alcatel-Lucent Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top