Zyxel VMG4325-B10A Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Zyxel

VMG4325-B10A

Page 91 / 367 Scroll up to view Page 86 - 90

Chapter 6 Broadband

VMG4380-B10A / VMG4325-B10A User’s Guide

The following table describes the labels in this screen.

Table 11

Network Setting

Broadband > 3G Backup

LABEL

DESCRIPTION

General

3G Backup

Select

Enable

to have the Device use the 3G connection as your WAN or a backup when the

wired WAN connection fails.

Ping Check

Select

Enable

if you want the Device to ping check the connection status of your WAN. You

can configure the frequency of the ping check and number of consecutive failures before

triggering 3G backup.

Check Cycle

Enter the frequency of the ping check in this field.

Consecutive

Fail

Enter how many consecutive failures are required before 3G backup is triggered.

Ping Default

Gateway

Select this to have the Device ping the WAN interface’s default gateway IP address.

Ping the Host

Select this to have the Device ping the particular host name or IP address you typed in this

field.

3G Connection Settings

Card

description

This field displays the manufacturer and model name of your 3G card if you inserted one in

the Device. Otherwise, it displays

N/A

Username

Type the user name (of up to 64 ASCII printable characters) given to you by your service

provider.

Password

Type the password (of up to 64 ASCII printable characters) associated with the user name

above.

A PIN (Personal Identification Number) code is a key to a 3G card. Without the PIN code,

you cannot use the 3G card.

If your ISP enabled PIN code authentication, enter the 4-digit PIN code (0000 for example)

provided by your ISP. If you enter the PIN code incorrectly, the 3G card may be blocked by

your ISP and you cannot use the account to access the Internet.

If your ISP disabled PIN code authentication, leave this field blank.

Dial string

Enter the phone number (dial string) used to dial up a connection to your service provider’s

base station. Your ISP should provide the phone number.

For example, *99# is the dial string to establish a GPRS or 3G connection in Taiwan.

APN

Enter the APN (Access Point Name) provided by your service provider. Connections with

different APNs may provide different services (such as Internet access or MMS (Multi-Media

Messaging Service)) and charge method.

You can enter up to 32 ASCII printable characters. Spaces are allowed.

Connection

Select

Nailed UP

if you do not want the connection to time out.

Select

on Demand

if you do not want the connection up all the time and specify an idle

time-out in the

Max Idle Timeout

field.

Max Idle

Timeout

This value specifies the time in minutes that elapses before the Device automatically

disconnects from the ISP.

Obtain an IP

Address

Automatically

Select this option If your ISP did not assign you a fixed IP address.

Use the

following static

IP address

Select this option If the ISP assigned a fixed IP address.

IP Address

Enter your WAN IP address in this field if you selected

Use the following static IP

address

Page 92 / 367

Chapter 6 Broadband

VMG4380-B10A / VMG4325-B10A User’s Guide

Obtain DNS

info

dynamically

Select this to have the Device get the DNS server addresses from the ISP automatically.

Use the

following static

DNS IP address

Select this to have the Device use the DNS server addresses you configure manually.

Primary DNS

server

Enter the first DNS server address assigned by the ISP.

Secondary DNS

server

Enter the second DNS server address assigned by the ISP.

Advanced

Click this to show the advanced 3G backup settings.

Budget Setup

Enable Budget

Control

Select

Enable

to set a monthly limit for the user account of the installed 3G card. You can

set a limit on the total traffic and/or call time. The Device takes the actions you specified

when a limit is exceeded during the month.

Time Budget

Select this and specify the amount of time (in hours) that the 3G connection can be used

within one month. If you change the value after you configure and enable budget control,

the Device resets the statistics.

Data Budget

(Mbytes)

Select this and specify how much downstream and/or upstream data (in Mega bytes) can be

transmitted via the 3G connection within one month.

Select

Download/Upload

to set a limit on the total traffic in both directions.

Select

Download

to set a limit on the downstream traffic (from the ISP to the Device).

Select

Upload

to set a limit on the upstream traffic (from the Device to the ISP).

If you change the value after you configure and enable budget control, the Device resets the

statistics.

Data Budget

(kPackets)

Select this and specify how much downstream and/or upstream data (in k Packets) can be

transmitted via the 3G connection within one month.

Select

Download/Upload

to set a limit on the total traffic in both directions.

Select

Download

to set a limit on the downstream traffic (from the ISP to the Device).

Select

Upload

to set a limit on the upstream traffic (from the Device to the ISP).

If you change the value after you configure and enable budget control, the Device resets the

statistics.

Reset all

budget

counters on

Select the date on which the Device resets the budget every month. Select

last

if you want

the Device to reset the budget on the last day of the month. Select

specific

and enter the

number of the date you want the Device to reset the budget

Reset time and

data budget

counters

Click this button to reset the time and data budgets immediately. The count starts over with

the 3G connection’s full configured monthly time and data budgets. This does not affect the

normal monthly budget restart; so if you configured the time and data budget counters to

reset on the second day of the month and you use this button on the first, the time and data

budget counters will still reset on the second.

Actions before

over budget

Specify the actions the Device takes before the time or data limit exceeds.

Enable % of

time budget/

data budget

(Mbytes)/data

budget

(kPackets)

Select

Enable

and enter a number from 1 to 99 in the percentage fields. If you change the

value after you configure and enable budget control, the Device resets the statistics.

Table 11

Network Setting

Broadband > 3G Backup (continued)

LABEL

DESCRIPTION

Page 93 / 367

Chapter 6 Broadband

VMG4380-B10A / VMG4325-B10A User’s Guide

6.4

The Advanced Screen

Use the

Advanced

screen to enable or disable PTM over ADSL, Annex M, and DSL PhyR functions.

The Device supports the PhyR retransmission scheme. PhyR is a retransmission scheme designed to

provide protection against noise on the DSL line. It improves voice, video and data transmission

resilience by utilizing a retransmission buffer.

6.4.1

DSL Bonding

If the DSLAM of your ISP supports DSL bonding, you can connect the two DSL ports on the Device

to two separate telephone jacks and enable the bonding feature in the

Advanced

screen.

DSL signals have distance limitations. VDSL2 (profile 17a) supports greater speed but offer shorter

distances (within 3000 ft). The farther away the subscribers are from the DSLAM, the slower the

speed. VDSL (profile 12a) provides longer distance range (over 3000 ft) but at lower speeds. DSL

bonding allows subscribers to use data streams spread over two DSL lines in order to (almost)

double the speed at longer distances. You may choose to use DSL bonding if the DSLAM supports it

and there are two DSL lines to the DSLAM.

The total available bandwidth for the subscriber then becomes the sum of the bandwidth available

for each of the subscriber’s line connections. The data rate depends on the DSL type, its standard/

profile, and the standard/profile that the DSLAM supports. The table below shows the transmission

data rate for single DSL line and DSL bonding.

Actions when

over budget

Specify the actions the Device takes when the time or data limit is exceeded.

Current 3G

connection

Select

Keep

to maintain an existing 3G connection or

Drop

to disconnect it.

Enable Email

Notification

Select this to enable the e-mail notification function. The Device will e-mail you a

notification when there over budget occurs.

Mail Server

Select a mail server for the e-mail address specified below.

If you do not select a mail server, e-mail notifications cannot be sent via e-mail. You must

have configured a mail server already in the

Maintenance

Email Notification

screen.

Over Budget

Email Title

Type a title that you want to be in the subject line of the e-mail notifications that the Device

sends.

Send

Notification to

Notifications are sent to the e-mail address specified in this field. If this field is left blank,

notifications cannot be sent via e-mail.

Interval

Enter the interval of how many minutes you want the Device to e-mail you.

Enable Log

Select this to activate the logging function at the interval you set in this field.

Basic

Click this to hide the advanced settings of 3G backup.

Apply

Click

Apply

to save your changes back to the Device.

Cancel

Click

Cancel

to return to the previous configuration.

Table 11

Network Setting

Broadband > 3G Backup (continued)

LABEL

DESCRIPTION

Page 94 / 367

Chapter 6 Broadband

VMG4380-B10A / VMG4325-B10A User’s Guide

Table 12

Comparison Table for Single DSL line and DSL Bonding

For a single VDSL2 line, the profile is 17a, which provides a maximum data rate of 100/60 Mbps

(downstream/upstream). A VDSL2 17a bonding profile can reach 200Mbps/100Mbps. If VDSL

bonding is used, the supported profile is 12a, which provides a maximum data rate of 50/25 Mbps

for each VDSL line. The ideal total data rate for the bonded connection is 100/50 Mbps.

For a single ADSL line, the standard with the highest data rate supported is ADSL2+, which

provides 25/1 Mbps data rate. When ADSL bonding is used, the data rate doubles to 50/2 Mbps.

In addition, DSL bonding supports ADSL bonding fallback. If a VDSL connection cannot be

established, the Device tries to use ADSL. If the VDSL connection is re-established, the Device

automatically switches back to VDSL. You must enable DSL bonding in order to use ADSL fallback.

Click

Network Setting > Broadband

Advanced

to display the following screen.

Figure 27

Network Setting

Broadband > Advanced

The following table describes the labels in this screen.

ITEM

VDSL2

VDSL BONDING

ADSL2+

ADSL(2+)

BONDING

PROFILE/

STANDARD

G993.2 Profile 17a

G993.2 Profile 12a

G.992.5

MAX.

DOWNSTREAM/

UPSTREAM

100/60 Mbps

50/25 x 2 = 100/50

Mbps

25/1 Mbps

25/1 x 2 = 50/2

Mbps

DISTANCE

within 3000 ft

over 3000 ft

over 5000 ft

5000 to 7000 ft

Table 13

Network Setting

Network Setting > Broadband

LABEL

DESCRIPTION

State

Select

Enable

to use the DSL bonding and ADSL fallback features. Make sure your ISP

supports these functions.

PTM over ADSL

Select

Enable

to use PTM over ADSL. Since PTM has less overhead than ATM, some ISPs

use PTM over ADSL for better performance.

Annex M

You can enable

Annex M

for the Device to use double upstream mode to increase the

maximum upstream transfer rate.

Page 95 / 367

Chapter 6 Broadband

VMG4380-B10A / VMG4325-B10A User’s Guide

6.5

The 8021x Screen

You can view and configure the 802.1x authentication settings in the

8021x

screen. Click

Network

Setting > Broadband

8021x

to display the following screen.

Figure 28

Network Setting

Broadband > 8021x

The following table describes the labels in this screen.

PhyR US

Enable or disable

PhyR US

(upstream) for upstream transmission to the WAN. PhyR US

should be enabled if data being transmitted upstream is sensitive to noise. However,

enabling PhyR US can decrease the US line rate. Enabling or disabling PhyR will require the

CPE to retrain. For PhyR to function, the DSLAM must also support PhyR and have it

enabled.

PhyR DS

Enable or disable

PhyR DS

(downstream) for downstream transmission from the WAN.

PhyR DS should be enabled if data being transmitted downstream is sensitive to noise.

However, enabling PhyR DS can decrease the DS line rate. Enabling or disabling PhyR will

require the CPE to retrain. For PhyR to function, the DSLAM must also support PhyR and

have it enabled.

Apply

Click

Apply

to save your changes back to the Device.

Cancel

Click

Cancel

to return to the previous configuration.

Table 13

Network Setting

Network Setting > Broadband (continued)

LABEL

DESCRIPTION

Table 14

Network Setting

Network Setting > 8021x

LABEL

DESCRIPTION

This is the index number of the entry.

Status

This field displays whether the authentication is active or not. A yellow bulb signifies that

this authentication is active. A gray bulb signifies that this authentication is not active.

Interface

This is the interface that uses the authentication. This displays

N/A

when there is no

interface assigned.

EAP Identity

This shows the EAP identity of the authentication. This displays

N/A

when there is no EAP

identity assigned.

EAP method

This shows the EAP method used in the authentication. This displays

N/A

when there is no

EAP method assigned.

Bidirectional

Authentication

This shows whether bidirectional authentication is allowed.

Certificate

This shows the certificate used for this authentication. This displays

N/A

when there is no

certificate assigned.

Trusted CA

This shows the Trusted CA used for this authentication. This displays

N/A

when there is no

Trusted CA assigned.

Rate

Popular Zyxel Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share