Page 216 / 382
Scroll up to view Page 211 - 215
Chapter 17 Dynamic DNS Setup
P-870HN-51b User’s Guide
216
Page 217 / 382
P-870HN-51b User’s Guide
217
C
HAPTER
18
Remote Management
18.1
Overview
This chapter explains how to configure the TR-069 settings and access control
settings on the Device.
18.1.1
What You Can Do in this Chapter
• The
TR-069
screen lets you configure the Device’s TR-069 auto-configuration
settings (
Section 18.3 on page 219
).
• The
TR-064
screen lets you enable management via TR-064 on the Device
(
Section 18.3 on page 219
)
• The
Service Control
screens let you configure through which interface(s) users
can use which service(s) to manage the Device (
Section 18.4 on page 220
).
• The
IP Address
screens let you configure from which IP address(es) users can
use a service to manage the Device (
Section 18.5 on page 221
).
18.2
The TR-069 Screen
TR-069 defines how Customer Premise Equipment (CPE), for example your
Device, can be managed over the WAN by an Auto Configuration Server (ACS).
TR-069 is based on sending Remote Procedure Calls (RPCs) between an ACS and a
client device. RPCs are sent in Extensible Markup Language (XML) format over
HTTP or HTTPS.
An administrator can use an ACS to remotely set up the Device, modify settings,
perform firmware upgrades as well as monitor and diagnose the Device. You have
enable the device to be managed by the ACS and specify the ACS IP address or
domain name and username and password.
Page 218 / 382
Chapter 18 Remote Management
P-870HN-51b User’s Guide
218
Click
Advanced > Remote MGMT
to open the following screen. Use this screen
to configure your P-870HN to be managed by an ACS.
Figure 108
TR-069
The following table describes the fields in this screen.
Table 77
TR-069
LABEL
DESCRIPTION
Inform
Select
Enable
to activate remote management via TR-069 on the
WAN. Otherwise, select
Disable
.
Inform Interval
Enter the time interval (in seconds) at which the Device sends
information to the auto-configuration server.
ACS URL
Enter the URL or IP address of the auto-configuration server.
ACS User Name
Enter the TR-069 user name for authentication with the auto-
configuration server.
ACS Password
Enter the TR-069 password for authentication with the auto-
configuration server.
WAN Interface
used by TR-069
client
Select a WAN interface through which the TR-069 traffic passes.
Display SOAP
messages on
serial console
Select
Enable
to show the SOAP messages on the console.
Connection
Request
Authentication
Select this option to enable authentication when there is a connection
request from the ACS.
Connection
Request User
Name
Enter the connection request user name.
When the ACS makes a connection request to the Device, this user
name is used to authenticate the ACS.
Page 219 / 382
Chapter 18 Remote Management
P-870HN-51b User’s Guide
219
18.3
The TR-064 Screen
TR-064 is a LAN-Side DSL CPE Configuration protocol defined by the DSL Forum.
TR-064 is built on top of UPnP. It allows the users to use a TR-064 compliant CPE
management application on the their computers from the LAN to discover the CPE
and configure user-specific parameters, such as the username and password.
Click
Advanced > Remote MGMT
>
TR064
to open the following screen.
Figure 109
TR-064
The following table describes the fields in this screen.
Connection
Request
Password
Enter the connection request password.
When the ACS makes a connection request to the Device, this
password is used to authenticate the ACS.
Connection
Request URL
This shows the connection request URL.
The ACS can use this URL to make a connection request to the Device.
Apply/Save
Click this button to save your changes back to the Device.
Cancel
Click
Cancel
to begin configuring this screen afresh.
Table 77
TR-069 (continued)
LABEL
DESCRIPTION
Table 78
TR-064
LABEL
DESCRIPTION
Enable TR064
Select the check box to activate management via TR-064 on the LAN.
Apply
Click this button to save your changes back to the Device.
Page 220 / 382
Chapter 18 Remote Management
P-870HN-51b User’s Guide
220
18.4
The Service Control Screen
Click
Advanced > Remote MGMT > Service Control
to open the following
screen. Use this screen to decide what services you may use to access which
Device interface.
Figure 110
Service Control
The following table describes the fields in this screen.
Table 79
Access Control: Services
LABEL
DESCRIPTION
Service Control
Select
Enable
to turn on service control. Otherwise, select
Disable
.
#
This is the index number of the entry.
Services
This is the service you may use to access the Device.
LAN
Select the
Enable
check box for the corresponding services that you
want to allow access to the Device from the LAN.
WAN
Select the
Enable
check box for the corresponding services that you
want to allow access to the Device from the WAN.
Apply
Click this button to save your changes back to the Device.
19216811.live