1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. P-663HN-51 Frontier
    5. /
  5. 6
Page 26 / 300 Scroll up to view Page 21 - 25
Chapter 1 Introducing the ZyXEL Device
P-663HN-51 User’s Guide
26
The following table describes the LEDs.
Table 1
Front Panel LEDs
LED
COLOR
STATUS
DESCRIPTION
POWER
Green
On
The ZyXEL Device is receiving power.
Blinking
The ZyXEL Device is performing a self-test.
Off
The ZyXEL Device is not receiving power.
ETHERNET
1,2,3,4
Green
On
The ZyXEL Device has a successful Ethernet
connection.
Blinking
The ZyXEL Device is sending/receiving data.
Off
The ZyXEL Device is not connected to the LAN.
WLAN/WPS
Green
On
The ZyXEL Device’s wireless interface is activated
and operating.
Blinking
The ZyXEL Device is communicating with other
wireless clients.
Orange
Blinking
The ZyXEL Device is setting up a WPS connection.
Off
The ZyXEL Device’s wireless interface is not
activated.
DSL1,
DSL2
Green
On
The respective DSL line is up.
Blinking
Fast blinking means the ZyXEL Device is initializing
the respective DSL line. Slow blinking means the
respective DSL line is down.
INTERNET
Green
On
The ZyXEL Device has an IP connection but no traffic.
Your device has a WAN IP address (either static or
assigned by a DHCP server), PPP negotiation was
successfully completed (if used) and the DSL
connection is up.
Red
On
The ZyXEL Device attempted to make an IP
connection but failed. Possible causes are no
response from a DHCP server, no PPPoE response,
PPPoE authentication failed.
Off
The ZyXEL Device does not have an IP connection.
Page 27 / 300
P-663HN-51 User’s Guide
27
C
HAPTER
2
Introducing the Web
Configurator
This chapter describes how to access and navigate the web configurator.
2.1
Web Configurator Overview
The web configurator is an HTML-based management interface that allows easy
ZyXEL Device setup and management via Internet browser. Use Internet Explorer
6.0 and later versions. The recommended screen resolution is 1024 by 768 pixels.
In order to use the web configurator you need to allow web browser pop-up
windows from your device. Web pop-up blocking is enabled by default in Windows
XP SP (Service Pack) 2. See
Appendix C on page 201
if you need to make sure
pop-ups are allowed in Internet Explorer.
2.2
Accessing the Web Configurator
The following describes how to access the ZyXEL Device from the LAN using the
administrator or user account. See
Section 25.5 on page 195
for information
about the support account.
1
Make sure your ZyXEL Device hardware is properly connected (see
Section 1.4 on
page 23
).
2
Assign your computer a static IP address (choose one from 192.168.1.2 to
192.168.1.254). See
Appendix A on page 217
for how to change your computer’s
IP address.
3
Launch your web browser.
4
Type "192.168.1.1" as the URL.
Page 28 / 300
Chapter 2 Introducing the Web Configurator
P-663HN-51 User’s Guide
28
5
A screen displays as shown.
Figure 5
Password Screen
2.2.1
User Access
The user account can only access the ZyXEL Device from the LAN. For user access,
enter the user account’s user name (
user
) and password (
1234
is the default)
and click
OK
to view the status only. The following screen appears.
Figure 6
User Status Screen
Page 29 / 300
Chapter 2 Introducing the Web Configurator
P-663HN-51 User’s Guide
29
2.2.2
Administrator Access
The
admin
account can only access the ZyXEL Device from the LAN.
For administrator access, enter the administrator user name (
admin
) and
password (
1234
is the default) and click
OK
to enter the configuration screens.
Note:
The management session automatically times out if it is left idle for five
minutes. Simply log back into the ZyXEL Device if this happens.
2.3
Resetting the ZyXEL Device
If you forget your password or cannot access the web configurator, you will need
to use the
RESET
button at the back of the ZyXEL Device to reload the factory-
default configuration file. This means that you will lose all configurations that you
had previously and the password will be reset to “1234”.
2.3.1
Using the Reset Button
1
Make sure the
POWER
LED is on (not blinking).
2
Press the
RESET
button for ten seconds or until the
POWER
LED begins to blink
and then release it. When the
POWER
LED begins to blink, the defaults have been
restored and the ZyXEL Device restarts.
Page 30 / 300
Chapter 2 Introducing the Web Configurator
P-663HN-51 User’s Guide
30
2.4
Navigating the Web Configurator
After you log in, use the sub-menus on the navigation panel to go to other
screens.
Some fields or links are not available if you entered the user password in
the login password screen (see
Figure 5 on page 28
).
Figure 7
Web Configurator: First Screen
Table 2
Web Configurator Screens Summary
LINK/ICON
SUB-LINK
FUNCTION
Device Info
Summary
This screen shows general device information such as
the firmware version, line rates, LAN IP address,
default gateway, and DNS servers.
WAN
This screen displays information about the ZyXEL
Device’s WAN connections.
Statistics
LAN
This screen displays statistics about the ZyXEL
Device’s LAN connections.
WAN
This screen displays statistics about the ZyXEL
Device’s WAN connections.
ATM
This screen shows low-level ATM protocol statistics.
ADSL
This screen displays statistics about the ZyXEL
Device’s ADSL connection.

Rate

4 / 5 based on 1 vote.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top