1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. P-661HNU-F1
    5. /
  5. 20
Page 96 / 404 Scroll up to view Page 91 - 95
Chapter 5 Broadband
P-661HNU-Fx User’s Guide
96
The following table describes the fields in this screen.
Table 7
Broadband Add/Edit: Routing- IPoE
Label
DESCRIPTION
General
Name
Enter a service name of the connection.
Type
ADSL
: The ZyXEL Device uses the ADSL technology for data
transmission over the DSL port.
Mode
Select
Routing
(default) from the drop-down list box if your ISP give
you one IP address only and you want multiple computers to share an
Internet account.
WAN Service
Type
This field is available only when you select
Routing
in the
Mode
field.
Select the method of encapsulation used by your ISP.
•
PPP over Ethernet (PPPoE)
- PPPoE (Point to Point Protocol over
Ethernet) provides access control and billing functionality in a
manner similar to dial-up services using PPP. Select this if you have
a username and password for Internet access.
•
IP over Ethernet
- In this type of Internet connection, IP packets
are routed between the Ethernet interface and the WAN interface
and then formatted so that they can be understood in a bridged
environment.
•
PPP over ATM
- PPPoA offers standard PPP features, such as
authentication, encryption, and compression. It is used as the
connection encapsulation method in an ATM based network, and it
can reduce overhead slightly compared to PPPoE.
ATM PVC
Configuration
VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define
a virtual circuit.
This section is available only when you select
ADSL
in the
Type
field
to configure an ATM layer-2 interface.
VPI
The valid range for the VPI is 0 to 255. Enter the VPI assigned to you.
VCI
The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local
management of ATM traffic). Enter the VCI assigned to you.
DSL Link Type
The DSL link type is set to
EoA
(Ethernet over ATM) to have an
Ethernet header in the packet, so that you can have multiple services/
connections over one PVC. You can set each connection to have its
own MAC address or all connections share one MAC address but use
different VLAN IDs for different services.
EoA
supports IPoE, PPPoE
and RFC1483/2684 bridging encapsulation methods.
Encapsulation
Mode
The encapsulation method of multiplexing used by your is
LLC/SNAP-
BRIDGING
. In LCC encapsulation, bridged PDUs are encapsulated by
identifying the type of the bridged media in the SNAP header.
Page 97 / 404
Chapter 5 Broadband
P-661HNU-Fx User’s Guide
97
Service Category
Select
UBR Without PCR
for applications that are non-time sensitive,
such as e-mail.
Select
CBR
(Constant Bit Rate) to specify fixed (always-on) bandwidth
for voice or data traffic.
Select
Non Realtime VBR
(non real-time Variable Bit Rate) for
connections that do not require closely controlled delay and delay
variation.
Select
Realtime VBR
(real-time Variable Bit Rate) for applications
with bursty connections that require closely controlled delay and delay
variation.
IP Address
This section is available only when you select
Routing
in the
Mode
field and
IPoE
in the
WAN Service Type
field.
Obtain an IP
Address
Automatically
A static IP address is a fixed IP that your ISP gives you. A dynamic IP
address is not fixed; the ISP assigns you a different one each time you
connect to the Internet. Select this if you have a dynamic IP address.
Enable DHCP
Option 60
Select this to identify the vendor and functionality of the ZyXEL Device
in DHCP requests that the ZyXEL Device sends to a DHCP server when
getting a WAN IP address.
Vendor Class
Identifier
Enter the Vendor Class Identifier (Option 60), such as the type of the
hardware or firmware.
Static IP Address
Select this option If the ISP assigned a fixed IP address.
IP Address
Enter the static IP address provided by your ISP.
Subnet Mask
Enter the subnet mask provided by your ISP.
Gateway IP
Address
Enter the gateway IP address provided by your ISP.
Routing Feature
NAT Enable
Select this option to activate NAT on this connection.
IGMP Proxy
Enable
Internet Group Multicast Protocol (IGMP) is a network-layer protocol
used to establish membership in a Multicast group - it is not used to
carry user data.
Select this option to have the ZyXEL Device act as an IGMP proxy on
this connection. This allows the ZyXEL Device to get subscribing
information and maintain a joined member list for each multicast
group. It can reduce multicast traffic significantly.
Apply as Default
Gateway
Select this option to have the ZyXEL Device use the WAN interface of
this connection as the system default gateway.
DNS Server
This is available only when you select
Apply as Default Gateway
in
the
Routing Feature
field.
Obtain DNS info
Automatically
Select this to have the ZyXEL Device get the DNS server addresses
from the ISP automatically.
Use the following
Static DNS IP
Address
Select this to have the ZyXEL Device use the DNS server addresses
you configure manually.
Primary DNS
Server
Enter the first DNS server address assigned by the ISP.
Table 7
Broadband Add/Edit: Routing- IPoE (continued)
Label
DESCRIPTION
Page 98 / 404
Chapter 5 Broadband
P-661HNU-Fx User’s Guide
98
5.2.1.3
Routing- PPPoA
Click the
Add new WAN Interface
in the
Network Setting > Broadband
screen or the
Edit
icon next to the connection you want to configure. Select
Routing
as the encapsulation mode and
PPoA
as the WAN service type.
Figure 18
Broadband Add/Edit: Routing- PPPoA
The following table describes the fields in this screen.
Secondary
DNS Server
Enter the second DNS server address assigned by the ISP.
Apply
Click
Apply
to save your changes.
Back
Click
Back
to return to the previous screen.
Table 7
Broadband Add/Edit: Routing- IPoE (continued)
Label
DESCRIPTION
Table 8
Broadband Add/Edit: Routing- PPPoA
Label
DESCRIPTION
General
Name
Enter a service name of the connection.
Type
ADSL
: The ZyXEL Device uses the ADSL technology for data
transmission over the DSL port.
Mode
Select
Routing
(default) from the drop-down list box if your ISP give
you one IP address only and you want multiple computers to share an
Internet account.
Page 99 / 404
Chapter 5 Broadband
P-661HNU-Fx User’s Guide
99
WAN Service
Type
This field is available only when you select
Routing
in the
Mode
field.
Select the method of encapsulation used by your ISP.
•
PPP over Ethernet (PPPoE)
- PPPoE (Point to Point Protocol over
Ethernet) provides access control and billing functionality in a
manner similar to dial-up services using PPP. Select this if you have
a username and password for Internet access.
•
IP over Ethernet
- In this type of Internet connection, IP packets
are routed between the Ethernet interface and the WAN interface
and then formatted so that they can be understood in a bridged
environment.
•
PPP over ATM
- PPPoA offers standard PPP features, such as
authentication, encryption, and compression. It is used as the
connection encapsulation method in an ATM based network, and it
can reduce overhead slightly compared to PPPoE.
ATM PVC
Configuration
VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define
a virtual circuit.
This section is available only when you select
ADSL
in the
Type
field
to configure an ATM layer-2 interface.
VPI
The valid range for the VPI is 0 to 255. Enter the VPI assigned to you.
VCI
The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local
management of ATM traffic). Enter the VCI assigned to you.
DSL Link Type
The DSL link type is set to
EoA
(Ethernet over ATM) to have an
Ethernet header in the packet, so that you can have multiple services/
connections over one PVC. You can set each connection to have its
own MAC address or all connections share one MAC address but use
different VLAN IDs for different services.
EoA
supports IPoE, PPPoE
and RFC1483/2684 bridging encapsulation methods.
Encapsulation
Mode
The encapsulation method of multiplexing used by your is
LLC/SNAP-
BRIDGING
. In LCC encapsulation, bridged PDUs are encapsulated by
identifying the type of the bridged media in the SNAP header.
Service Category
Select
UBR Without PCR
for applications that are non-time sensitive,
such as e-mail.
Select
CBR
(Constant Bit Rate) to specify fixed (always-on) bandwidth
for voice or data traffic.
Select
Non Realtime VBR
(non real-time Variable Bit Rate) for
connections that do not require closely controlled delay and delay
variation.
Select
Realtime VBR
(real-time Variable Bit Rate) for applications
with bursty connections that require closely controlled delay and delay
variation.
IP Address
This section is available only when you select
Routing
in the
Mode
field and
IPoE
in the
WAN Service Type
field.
PPP Information - This section is available only when you select
Routing
in the
Mode
field and
PPPoE
in the
WAN Service Type
field.
PPP User Name
Enter the user name exactly as your ISP assigned. If assigned a name
in the form user@domain
where domain identifies a service name,
then enter both components exactly as given.
PPP Password
Enter the password associated with the user name above.
Table 8
Broadband Add/Edit: Routing- PPPoA
Label
DESCRIPTION
Page 100 / 404
Chapter 5 Broadband
P-661HNU-Fx User’s Guide
100
Authentication
Method
The ZyXEL Device supports PAP (Password Authentication Protocol)
and CHAP (Challenge Handshake Authentication Protocol). CHAP is
more secure than PAP; however, PAP is readily available on more
platforms.
Use the drop-down list box to select an authentication protocol for
outgoing calls. Options are:
AUTO
: Your ZyXEL Device accepts either CHAP or PAP when requested
by this remote node.
PAP
: Your ZyXEL Device accepts PAP only.
CHAP
: Your ZyXEL Device accepts CHAP only.
MSCHAP
: Your ZyXEL Device accepts MSCHAP only. MS-CHAP is the
Microsoft version of the CHAP.
Use Static IP
Address
A static IP address is a fixed IP that your ISP gives you. A dynamic IP
address is not fixed; the ISP assigns you a different one each time you
connect to the Internet. Select this if you do not have a dynamic IP
address.
IP Address
Enter the static IP address provided by your ISP. You will only see this
field if you select
Use Static IP Address
Routing Feature
NAT Enable
Select this option to activate NAT on this connection.
IGMP Proxy
Enable
Internet Group Multicast Protocol (IGMP) is a network-layer protocol
used to establish membership in a Multicast group - it is not used to
carry user data.
Select this option to have the ZyXEL Device act as an IGMP proxy on
this connection. This allows the ZyXEL Device to get subscribing
information and maintain a joined member list for each multicast
group. It can reduce multicast traffic significantly.
Apply as Default
Gateway
Select this option to have the ZyXEL Device use the WAN interface of
this connection as the system default gateway.
DNS Server - This section is not available when you select
Bridge
in the
WAN Service
Type
field.
Obtain DNS info
Automatically
Select this to have the ZyXEL Device get the DNS server addresses
from the ISP automatically.
Use the following
Static DNS IP
Address
Select this to have the ZyXEL Device use the DNS server addresses
you configure manually.
Primary DNS
Server
Enter the first DNS server address assigned by the ISP.
Secondary
DNS Server
Enter the second DNS server address assigned by the ISP.
Apply
Click
Apply
to save your changes.
Back
Click
Back
to return to the previous screen.
Table 8
Broadband Add/Edit: Routing- PPPoA
Label
DESCRIPTION

Rate

4 / 5 based on 1 vote.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top