1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. P-660R-F1
    5. /
  5. 8
Page 36 / 268 Scroll up to view Page 31 - 35
Chapter 3 Wizard Setup for Internet Access
P-660R-F1 Series User’s Guide
36
2
Click
Next
to confirm your settings and test your connection.
Figure 14
Auto-Detection: PPPoE
3.2.2
Manual Configuration
1
If the ZyXEL Device fails to detect your DSL connection type, enter the Internet access information
given to you by your ISP exactly in the wizard screen. If not given, leave the fields set to the
default.
Figure 15
Internet Access Wizard Setup: ISP Parameters
Page 37 / 268
Chapter 3 Wizard Setup for Internet Access
P-660R-F1 Series User’s Guide
37
The following table describes the fields in this screen.
2
The next wizard screen varies depending on what mode and encapsulation type you use. All screens
shown are with routing mode. Configure the fields and click
Next
to continue.
Figure 16
Internet Connection with PPPoE
Table 7
Internet Access Wizard Setup: ISP Parameters
LABEL
DESCRIPTION
Mode
From the
Mode
drop-down list box, select
Routing
(default) if your ISP allows
multiple computers to share an Internet account. Otherwise select
Bridge
.
Encapsulation
Select the encapsulation type your ISP uses from the
Encapsulation
drop-down list
box. Choices vary depending on what you select in the
Mode
field.
If you select
Bridge
in the
Mode
field, select either
PPPoA
or
RFC 1483
.
If you select
Routing
in the
Mode
field, select
PPPoA
,
RFC 1483
,
ENET ENCAP
or
PPPoE
.
Multiplexing
Select the multiplexing method used by your ISP from the
Multiplex
drop-down list
box either VC-based or LLC-based.
Virtual Circuit
ID
VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual
circuit. Refer to the appendix
for more information.
VPI
Enter the VPI assigned to you. This field may already be configured.
VCI
Enter the VCI assigned to you. This field may already be configured.
Back
Click
Back
to go back to the previous screen.
Next
Click
Next
to continue to the next wizard screen. The next wizard screen you see
depends on what protocol you chose above.
Exit
Click
Exit
to close the wizard screen without saving your changes.
Page 38 / 268
Chapter 3 Wizard Setup for Internet Access
P-660R-F1 Series User’s Guide
38
The following table describes the fields in this screen.
Figure 17
Internet Connection with RFC 1483
Table 8
Internet Connection with PPPoE
LABEL
DESCRIPTION
User Name
Enter the user name exactly as your ISP assigned. If assigned a name in the form
user@domain where domain identifies a service name, then enter both components
exactly as given.
Password
Enter the password associated with the user name above.
Service Name
Type the name of your PPPoE service here.
Back
Click
Back
to go back to the previous wizard screen.
Apply
Click
Apply
to save your changes back to the ZyXEL Device.
Exit
Click
Exit
to close the wizard screen without saving your changes.
Page 39 / 268
Chapter 3 Wizard Setup for Internet Access
P-660R-F1 Series User’s Guide
39
The following table describes the fields in this screen.
Figure 18
Internet Connection with ENET ENCAP
Table 9
Internet Connection with RFC 1483
LABEL
DESCRIPTION
IP Address
This field is available if you select
Routing
in the
Mode
field.
Type your ISP assigned IP address in this field.
Back
Click
Back
to go back to the previous wizard screen.
Next
Click
Next
to continue to the next wizard screen.
Exit
Click
Exit
to close the wizard screen without saving your changes.
Page 40 / 268
Chapter 3 Wizard Setup for Internet Access
P-660R-F1 Series User’s Guide
40
The following table describes the fields in this screen.
Figure 19
Internet Connection with PPPoA
The following table describes the fields in this screen.
Table 10
Internet Connection with ENET ENCAP
LABEL
DESCRIPTION
Obtain an IP
Address
Automatically
A static IP address is a fixed IP that your ISP gives you. A dynamic IP address is not
fixed; the ISP assigns you a different one each time you connect to the Internet.
Select
Obtain an IP Address Automatically
if you have a dynamic IP address.
Static IP
Address
Select
Static IP Address
if your ISP gives you a fixed IP address.
IP Address
Enter your ISP assigned IP address.
Subnet Mask
Enter a subnet mask in dotted decimal notation.
Refer to the appendices
to calculate a subnet mask If you are implementing
subnetting.
Gateway IP
address
You must specify a gateway IP address (supplied by your ISP) when you use
ENET
ENCAP
in the
Encapsulation
field in the previous screen.
First DNS
Server
Enter the IP addresses of the DNS servers. The DNS servers are passed to the DHCP
clients along with the IP address and the subnet mask.
Second DNS
Server
As above.
Back
Click
Back
to go back to the previous wizard screen.
Apply
Click
Apply
to save your changes back to the ZyXEL Device.
Exit
Click
Exit
to close the wizard screen without saving your changes.
Table 11
Internet Connection with PPPoA
LABEL
DESCRIPTION
User Name
Enter the login name that your ISP gives you.
Password
Enter the password associated with the user name above.
Back
Click
Back
to go back to the previous wizard screen.

Rate

4.5 / 5 based on 2 votes.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top