Zyxel P-2612HNU-F1F PLDT Router Manual PDF (Setup & Configuration Guide)

Page 101 / 424 Scroll up to view Page 96 - 100

Chapter 5 Broadband

P-2612HNU-Fx User’s Guide

101

The following table describes the fields in this screen.

Table 7

Broadband Add/Edit: Routing- PPPoE

Label

DESCRIPTION

General

Name

Enter a service name of the connection.

Type

Select an interface for which you want to configure here.

ADSL

: The ZyXEL Device uses the ADSL technology for data

transmission over the DSL port.

EtherWAN

: The ZyXEL Device transmits data over the Ethernet WAN

port. Select this if you have a DSL router or modem in your network

already.

Mode

Select

Routing

(default) from the drop-down list box if your ISP give

you one IP address only and you want multiple computers to share an

Internet account.

WAN Service

Type

This field is available only when you select

Routing

in the

Mode

field.

Select the method of encapsulation used by your ISP.

•

PPP over Ethernet (PPPoE)

- PPPoE (Point to Point Protocol over

Ethernet) provides access control and billing functionality in a

manner similar to dial-up services using PPP. Select this if you have

a username and password for Internet access.

•

IP over Ethernet

- In this type of Internet connection, IP packets

are routed between the Ethernet interface and the WAN interface

and then formatted so that they can be understood in a bridged

environment.

ATM PVC

Configuration

VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define

a virtual circuit.

This section is available only when you select

ADSL

in the

Type

field

to configure an ATM layer-2 interface.

VPI

The valid range for the VPI is 0 to 255. Enter the VPI assigned to you.

VCI

The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local

management of ATM traffic). Enter the VCI assigned to you.

DSL Link Type

The DSL link type is set to

EoA

(Ethernet over ATM) to have an

Ethernet header in the packet, so that you can have multiple services/

connections over one PVC. You can set each connection to have its

own MAC address or all connections share one MAC address but use

different VLAN IDs for different services.

EoA

supports IPoE, PPPoE

and RFC1483/2684 bridging encapsulation methods.

Encapsulation

Mode

The encapsulation method of multiplexing used by your is

LLC/SNAP-

BRIDGING

. In LCC encapsulation, bridged PDUs are encapsulated by

identifying the type of the bridged media in the SNAP header.

Page 102 / 424

Chapter 5 Broadband

P-2612HNU-Fx User’s Guide

102

Service Category

Select

UBR Without PCR

for applications that are non-time sensitive,

such as e-mail.

Select

CBR

(Constant Bit Rate) to specify fixed (always-on) bandwidth

for voice or data traffic.

Select

Non Realtime VBR

(non real-time Variable Bit Rate) for

connections that do not require closely controlled delay and delay

variation.

Select

Realtime VBR

(real-time Variable Bit Rate) for applications

with bursty connections that require closely controlled delay and delay

variation.

Peak Cell Rate

Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find

the Peak Cell Rate (PCR). This is the maximum rate at which the

sender can send cells. Type the PCR here.

This field is not available when you select

UBR Without PCR

.

Sustainable

Cell Rate

The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that

can be transmitted. Type the SCR, which must be less than the PCR.

Note that system default is 0 cells/sec.

This field is available only when you select

Non Realtime VBR

or

Realtime VBR

.

Maximum

Burst Size

Maximum Burst Size (MBS) refers to the maximum number of cells

that can be sent at the peak rate. Type the MBS, which is less than

65535.

This field is available only when you select

Non Realtime VBR

or

Realtime VBR

.

VLAN

This section is available only when you select

EtherWAN

in the

Type

field.

Enable VLAN

Select this to add the VLAN tag (specified below) to the outgoing

traffic through this connection.

Enter 802.1P

Priority

IEEE 802.1p defines up to 8 separate traffic types by inserting a tag

into a MAC-layer frame that contains bits to define class of service.

Type the IEEE 802.1p priority level (from 0 to 7) to add to traffic

through this connection. The greater the number, the higher the

priority level.

Enter 802.1Q

VLAN ID

Type the VLAN ID number (from 1 to 4094) for traffic through this

connection.

PPP Information

This section is available only when you select

Routing

in the

Mode

field and

PPPoE

in the

WAN Service Type

field.

PPP User Name

Enter the user name exactly as your ISP assigned. If assigned a name

in the form user@domain

where domain identifies a service name,

then enter both components exactly as given.

PPP Password

Enter the password associated with the user name above.

PPPoE Service

Name

Type the name of your PPPoE service here.

Table 7

Broadband Add/Edit: Routing- PPPoE (continued)

Label

DESCRIPTION

Page 103 / 424

Chapter 5 Broadband

P-2612HNU-Fx User’s Guide

103

Authentication

Mode

The ZyXEL Device supports PAP (Password Authentication Protocol)

and CHAP (Challenge Handshake Authentication Protocol). CHAP is

more secure than PAP; however, PAP is readily available on more

platforms.

Use the drop-down list box to select an authentication protocol for

outgoing calls. Options are:

AUTO

: Your ZyXEL Device accepts either CHAP or PAP when requested

by this remote node.

CHAP

: Your ZyXEL Device accepts CHAP only.

PAP

: Your ZyXEL Device accepts PAP only.

MSCHAP

: Your ZyXEL Device accepts MSCHAP only. MS-CHAP is the

Microsoft version of the CHAP.

Use Static IP

Address

A static IP address is a fixed IP that your ISP gives you. A dynamic IP

address is not fixed; the ISP assigns you a different one each time you

connect to the Internet. Select this if you want to get a dynamic IP

address from the ISP.

IP Address

Enter the static IP address provided by your ISP.

PPPoE

Passthrough

In addition to the ZyXEL Device’s built-in PPPoE client, you can enable

PPPoE pass through to allow up to ten hosts on the LAN to use PPPoE

client software on their computers to connect to the ISP via the ZyXEL

Device. Each host can have a separate account and a public WAN IP

address.

PPPoE pass through is an alternative to NAT for application where NAT

is not appropriate.

Disable PPPoE pass through if you do not need to allow hosts on the

LAN to use PPPoE client software on their computers to connect to the

ISP.

Routing Feature

NAT Enable

Select this option to activate NAT on this connection.

IGMP Proxy

Enable

Internet Group Multicast Protocol (IGMP) is a network-layer protocol

used to establish membership in a Multicast group - it is not used to

carry user data.

Select this option to have the ZyXEL Device act as an IGMP proxy on

this connection. This allows the ZyXEL Device to get subscribing

information and maintain a joined member list for each multicast

group. It can reduce multicast traffic significantly.

Apply as Default

Gateway

Select this option to have the ZyXEL Device use the WAN interface of

this connection as the system default gateway.

DNS Server

The section is not available when you select

Bridge

in the

WAN

Service Type

field.

Obtain DNS info

Automatically

Select this to have the ZyXEL Device get the DNS server addresses

from the ISP automatically.

Use the following

Static DNS IP

Address

Select this to have the ZyXEL Device use the DNS server addresses

you configure manually.

Table 7

Broadband Add/Edit: Routing- PPPoE (continued)

Label

DESCRIPTION

Page 104 / 424

Chapter 5 Broadband

P-2612HNU-Fx User’s Guide

104

5.2.1.2

Routing- IPoE

Click the

Add new WAN Interface

in the

Network Setting > Broadband

screen or the

Edit

icon next to the connection you want to configure. Select

Routing

as the encapsulation mode and

IPoE

as the WAN service type.

Primary DNS

Server

Enter the first DNS server address assigned by the ISP.

Secondary

DNS Server

Enter the second DNS server address assigned by the ISP.

Apply

Click

Apply

to save your changes.

Back

Click

Back

to return to the previous screen.

Table 7

Broadband Add/Edit: Routing- PPPoE (continued)

Label

DESCRIPTION

Page 105 / 424

Chapter 5 Broadband

P-2612HNU-Fx User’s Guide

105

Broadband Add/Edit: Routing- IPoE

The following table describes the fields in this screen.

Table 8

Broadband Add/Edit: Routing- IPoE

Label

DESCRIPTION

General

Name

Enter a service name of the connection.

Rate

Popular Zyxel Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share