Zyxel P-2602R-D1A Router Manual PDF (Setup & Configuration Guide)
Given below is full router user manual of Zyxel P-2602R-D1A router model. You can also download this manual in PDF Format to read later on your computer.
Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.
Page 1 / 11
P-2602R/RL-DxA
ADSL2+ VoIP IAD
Quick Start Guide
Version 3.40
5/2006
Edition 1
Page 2 / 11
P-2602R/RL-DxA Quick Start Guide
2
Overview
The P-2602R/RL-DxA ADSL2+ VoIP Integrated Access Device (IAD) is an ADSL2+ router with phone ports for
making calls over the Internet (Voice over IP or VoIP). It can also use regular phone services through regular
(PSTN) phone lines. See the User’s Guide for more information on all features.
The following figure shows how your P-2602R/RL-DxA (
A
) connects your network to the Internet, provides
firewall protection and allows you to make telephone calls over the Internet. Additionally, the P-2602RL-D
model can be used to make calls over regular telephone (PSTN) lines.
1 Requirements
Make sure you have the following things before you set up your P-2602R/RL-DxA.
•
Internet access - account information provided by your ISP, such as user name, password, and so on.
•
VoIP account - You need the account information provided by your VoIP service provider (the company that lets
you make phone calls over the Internet). This information might include your URI, number, and so on.
•
Internet Explorer 6.0 or later or Netscape Navigator 7.0 or later, with JavaScript enabled.
2 Hardware Connections
Hardware connections vary by model. The P-2602RL-DxA models have a built in lifeline and the P-2602R-
DxA do not.
Page 3 / 11
P-2602R/RL-DxA Quick Start Guide
3
2.1 P-2602RL-DxA Hardware Connections
1 DSL
: Use the gray ADSL cable to connect the telephone jack or the
DSL
or
MODEM
jack on a splitter to
this port.
2 LINE
: Use the green PSTN line cable to connect the telephone jack or the
TEL
or
PHONE
jack on a splitter to
this port.
Note: When the P-2602R/RL-DxA does not have power, only the phone connected to the
PHONE 2
port can be used for making calls. Ensure you know which phone this is, so
that in case of emergency you can make outgoing calls.
3 ETHERNET
: Use an Ethernet cable to connect a computer to this
port for initial configuration and/or
Internet access.
4
PHONE 1-2
: Use telephone cables (and any telephone adaptors provided with your P-2602RL-DxA) to
connect your telephones to these ports. If you only have one telephone, you should use port 1.
5 POWER
:
Use the power adaptor provided with your P-2602RL-DxA to connect an appropriate power
source to this socket.
Note:
If you are using T-ISDN (UR-2), connect the green wire to a TAE connector before connecting it
to a telephone wall jack or the telephone splitter's
TEL
or
PHONE
jack.
Page 4 / 11
P-2602R/RL-DxA Quick Start Guide
4
6
Push in the
POWER
button. Look at the lights on the front panel of the P-2602RL-DxA.
• The
POWER
light blinks during start-up and is green once the P-2602RL-DxA is ready.
• Each
ETHERNET
light turns on if the corresponding
ETHERNET
port is properly con-
nected. The lights blink when the P-2602RL-DxA is sending or receiving data through the
corresponding
ETHERNET
port.
• The
DSL
light stays on if a physical connection with the ISP is established. The
INTER-
NET
light stays on when Internet access is available.
• The
PHONE
lights stay on when your SIP account is registered and they blink if the
receiver is off hooked.
If
PHONE 1
or
PHONE 2
light is on, skip to Section
4
to see how to make calls through
the Internet.
If the
INTERNET
light comes on but the
PHONE
lights are off, go to Section
3.2
and use
the
VOICE OVER INTERNET SETUP
wizard.
If the
INTERNET
light is off but the
DSL
light is on, go to Section
3.1
and use the
INTERNET
SETUP
wizard to configure your Internet access settings.
Page 5 / 11
P-2602R/RL-DxA Quick Start Guide
5
2.2 P-2602R-DxA Hardware Connections
1 DSL
: Use the gray ADSL cable to connect the telephone jack or the
DSL
or
MODEM
jack on a splitter to
this port.
2 ETHERNET
: Use an Ethernet cable to connect a computer to this
port for initial configuration and/or
Internet access.
3
PHONE 1-2
: Use a telephone cable (and any telephone adaptors provided with your P-2602R-DxA) to
connect your telephones to these ports. If you only have one telephone, you should use port 1.
4 POWER
:
Use the power adaptor provided with your P-2602R-DxA to connect an appropriate power source
to this socket.
Note:
If you are using T-ISDN (UR-2), connect the green wire to a TAE connector before connecting it
to a telephone wall jack or the telephone splitter's
19216811.live