1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. NBG334W
    5. /
  5. 14
Page 66 / 296 Scroll up to view Page 61 - 65
Chapter 4 AP Mode
NBG334W User’s Guide
66
4.3.1
Navigation Panel
Use the menu in the navigation panel to configure NBG334W features in
AP Mode
.
The following screen and table show the features you can configure in
AP Mode
.
Figure 31
Menu: AP Mode
The following table describes the sub-menus.
Rate
For the LAN ports, this displays the port speed and duplex setting or
N/A
when the
line is disconnected.
For the WLAN, it displays the maximum transmission rate when the WLAN is
enabled and
N/A
when the WLAN is disabled.
Summary
Packet Statistics
Use this screen to view port status and packet specific statistics.
WLAN Station Status
Use this screen to view the wireless stations that are currently associated to the
NBG334W.
Table 22
Web Configurator Status Screen (continued)
LABEL
DESCRIPTION
Table 23
Screens Summary
LINK
TAB
FUNCTION
Status
This screen shows the NBG334W’s general device, system and
interface status information. Use this screen to access the wizard,
and summary statistics tables.
Network
Page 67 / 296
Chapter 4 AP Mode
NBG334W User’s Guide
67
4.4
Configuring Your Settings
4.4.1
LAN Settings
Use this section to configure your LAN settings while in
AP Mode
.
Click
Network > LAN
to see the screen below.
"
If you change the IP address of the NBG334W in the screen below, you will
need to log into the NBG334W again using the new IP address.
Wireless
LAN
General
Use this screen to configure wireless LAN.
MAC Filter
Use the MAC filter screen to configure the NBG334W to block
access to devices or block the devices from accessing the
NBG334W.
Advanced
This screen allows you to configure advanced wireless settings.
QoS
Use this screen to configure Wi-Fi Multimedia Quality of Service
(WMM QoS). WMM QoS allows you to prioritize wireless traffic
according to the delivery requirements of individual services.
WPS
Use this screen to configure WPS.
WPS Station
Use this screen to add a wireless station using WPS.
LAN
IP
Use this screen to configure LAN IP address and subnet mask or to
get the LAN IP address from a DHCP server.
Maintenance
System
General
Use this screen to view and change administrative settings such as
system and domain names, password and inactivity timer.
Time Setting
Use this screen to change your NBG334W’s time and date.
Logs
View Log
Use this screen to view the logs for the categories that you
selected.
Log Settings
Use this screen to change your NBG334W’s log settings.
Tools
Firmware
Use this screen to upload firmware to your NBG334W.
Configuration
Use this screen to backup and restore the configuration or reset
the factory defaults to your NBG334W.
Restart
This screen allows you to reboot the NBG334W without turning the
power off.
Config Mode
General
This screen allows you to display or hide the advanced screens or
features.
Language
This screen allows you to select the language you prefer.
Table 23
Screens Summary
LINK
TAB
FUNCTION
Page 68 / 296
Chapter 4 AP Mode
NBG334W User’s Guide
68
Figure 32
Network > LAN > IP
The table below describes the labels in the screen.
Table 24
Network > LAN > IP
4.4.2
WLAN and Maintenance Settings
The configuration of wireless and maintenance settings in
AP Mode
is the same as for
Router
Mode
.
•
See
Chapter 5 on page 69
for information on the configuring your wireless network.
•
See
Maintenance and Troubleshooting
(187)
for information on the configuring your
Maintenance settings.
4.5
Logging in to the Web Configurator in AP Mode
1
Connect your computer to the LAN port of the NBG334W.
2
The default IP address if the NBG334W is “192.168.1.1”. In this case, your computer
must have an IP address in the range between “192.168.1.2” and “192.168.1.255”.
3
Click
Start > Run
on your computer in Windows.
LABEL
DESCRIPTION
Get form
DHCP Server
Select this option to allow the NBG334W to obtain an IP address from a DHCP
server on the network. You must connect the WAN port to a device with a DHCP
server enabled (such as a router or gateway). Without a DHCP server the NBG334W
will have no IP address. You need to find out the IP address the DHCP server
assigns to the NBG334W and use that address to log in to the NBG334W again.
User Defined
LAN IP
Select this option to set the NBG334W’s IP address. This setting is selected by
default. Check the IP address is on the same domain as other devices on your
network.
IP Address
Type the IP address in dotted decimal notation. The default setting is 192.168.1.1. If
you change the IP address you will have to log in again with the new IP address.
IP Subnet
Mask
The subnet mask specifies the network number portion of an IP address. Your
NBG334W will automatically calculate the subnet mask based on the IP address that
you assign. Unless you are implementing subnetting, use the subnet mask computed
by the NBG334W.
Gateway IP
Address
Type the IP address of the gateway. The gateway is an immediate neighbor of your
NBG334W that will forward the packet to the destination. In
AP Mode
, the gateway
must be a router on the same segment as your NBG334W.
Apply
Click
Apply
to save your changes to the NBG334W.
Reset
Click
Reset
to reload the previous configuration for this screen.
Page 69 / 296
Chapter 4 AP Mode
NBG334W User’s Guide
69
4
Type “cmd” in the dialog box.
5
Type “ipconfig” to show your computer’s IP address. If your computer’s IP address is
not in the correct range then see
Appendix D on page 249
for information on changing
your computer’s IP address.
6
After you’ve set your computer’s IP address, open a web browser such as Internet
Explorer and type “192.168.1.1” as the web address in your web browser.
See
Chapter 6 on page 93
for a tutorial on setting up a network with an AP.
Page 70 / 296
Chapter 4 AP Mode
NBG334W User’s Guide
70

Rate

4 / 5 based on 1 vote.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top