1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. F1000
    5. /
  5. 5
Page 21 / 359 Scroll up to view Page 16 - 20
Chapter 1 Introducing the Device
eircom F1000 Modem User’s Guide
21
INTERNET
Green
On
The Device has an IP connection but no traffic.
Your device has a WAN IP address (either static or assigned by a DHCP
server), PPP negotiation was successfully completed (if used) and the
DSL connection is up.
Blinking
The Device is sending or receiving IP traffic.
Off
There is no Internet connection or the gateway is in bridged mode.
Red
On
The Device attempted to make an IP connection but failed. Possible
causes are no response from a DHCP server, no PPPoE response, PPPoE
authentication failed.
WAN
Green
On
The Device has a successful 1000 Mbps Ethernet connection on the
WAN.
Blinking
The Device is sending or receiving data to/from the WAN at 1000 Mbps.
Orange
On
The Device has a successful 10/100 Mbps Ethernet connection on the
WAN.
Blinking
The Device is sending or receiving data to/from the WAN at 10/100
Mbps.
Off
There is no Ethernet connection on the WAN.
LAN
Green
On
The Device has a successful 1000 Mbps Ethernet connection with a
device on the Local Area Network (LAN).
Blinking
The Device is sending or receiving data to/from the LAN at 1000 Mbps.
Off
The Device does not have an Ethernet connection with the LAN.
WiFi 2.4G
Green
On
The 2.4 GHz wireless network is activated.
Blinking
The Device is communicating with other wireless clients.
Orange
Blinking
The Device is setting up a WPS connection.
Off
The 2.4 GHz wireless network is not activated.
Phone1,
Phone2
Green
On
A SIP account is registered for the phone port.
Blinking
A telephone connected to the phone port has its receiver off of the hook
or there is an incoming call.
Orange
On
A SIP account is registered for the phone port and there is a voice
message in the corresponding SIP account.
Blinking
A telephone connected to the phone port has its receiver off of the hook
and there is a voice message in the corresponding SIP account.
Off
The phone port does not have a SIP account registered.
USB1
Green
On
The Device recognizes a USB connection through the USB1 slot.
Blinking
The Device is sending/receiving data to /from the USB device connected
to it.
Off
The Device does not detect a USB connection through the USB1 slot.
USB2
Green
On
The Device recognizes a USB connection through the USB2 slot.
Blinking
The Device is sending/receiving data to /from the USB device connected
to it.
Off
The Device does not detect a USB connection through the USB2 slot.
Table 1
LED Descriptions (continued)
LED
COLOR
STATUS
DESCRIPTION
Page 22 / 359
Chapter 1 Introducing the Device
eircom F1000 Modem User’s Guide
22
1.6
The RESET Button
If you forget your password or cannot access the Web Configurator, you will need to use the
RESET
button at the back of the device to reload the factory-default configuration file. This means that you
will lose all configurations that you had previously and the password will be reset to the default
password printed on the back of the Device.
1
Make sure the
PWR/SYS
LED is on (not blinking).
2
To set the device back to the factory default settings, press the
RESET
button for ten seconds or
until the
PWR/SYS
LED begins to blink and then release it. When the
PWR/SYS
LED begins to
blink, the defaults have been restored and the device restarts.
1.7
Wireless Access
The Device is a wireless Access Point (AP) for wireless clients, such as notebook computers or PDAs
and iPads. It allows them to connect to the Internet without having to rely on inconvenient Ethernet
cables.
You can configure your wireless network in either the built-in Web Configurator, or using the WPS
button.
Figure 6
Wireless Access Example
1.7.1
Using the Wi-Fi and WPS Buttons
If the wireless network is turned off, press the
Wi-Fi
button for one second. Once the
WiFi 2.4G
LED turns green, the wireless network is active.
You can also use the
WPS
button to quickly set up a secure wireless connection between the Device
and a WPS-compatible client by adding one device at a time.
To activate WPS:
1
Make sure the
PWR/SYS
LED is on and not blinking.
2
Press the
WPS
button for five seconds and release it.
Page 23 / 359
Chapter 1 Introducing the Device
eircom F1000 Modem User’s Guide
23
3
Press the WPS button on another WPS-enabled device within range of the Device. The
WiFi 2.4G
LED flashes orange while the Device sets up a WPS connection with the other wireless device.
4
Once the connection is successfully made, the
WiFi 2.4G
LED shines green.
To turn off the wireless network, press the
Wi-Fi
button for one to five seconds. The
WiFi 2.4G
LED turns off when the wireless network is off.
1.8
Wall-mounting Instructions
Do the following to hang your Device on a wall.
1
Locate a high position on a wall that is free of obstructions. Use a sturdy wall.
2
Hold the bracket against the wall and mark where to drill the holes.
3
Drill the two screw holes in the wall.
Be careful to avoid damaging pipes or cables located inside the wall
when drilling holes for the screws.
4
Align and insert the bracket to the wall-mounting notches on the rear panel of the Device.
Page 24 / 359
Chapter 1 Introducing the Device
eircom F1000 Modem User’s Guide
24
5
Push the bracket up to tightly attach it to the Device.
6
Mount the Device on the screws which are already installed on the wall. Make sure that the Device
is firmly attached to the screws so it does not fall off.
Page 25 / 359
eircom F1000 Modem User’s Guide
25
C
HAPTER
2
The Web Configurator
2.1
Overview
The web configurator is an HTML-based management interface that allows easy device setup and
management via Internet browser. Use Internet Explorer 6.0 and later versions or Mozilla Firefox 3
and later versions or Safari 2.0 and later versions. The recommended screen resolution is 1024 by
768 pixels.
In order to use the web configurator you need to allow:
•
Web browser pop-up windows from your device. Web pop-up blocking is enabled by default in
Windows XP SP (Service Pack) 2.
•
JavaScript (enabled by default).
•
Java permissions (enabled by default).
See
Appendix C on page 315
if you need to make sure these functions are allowed in Internet
Explorer.
2.1.1
Accessing the Web Configurator
1
Make sure your Device hardware is properly connected (refer to the Quick Start Guide).
2
Launch your web browser.
3
Type "192.168.1.254" as the URL.
4
A password screen displays. Type “admin” (default) as the username and enter the default
password (which is the same as the wireless key on the Device’s back label), then click
Login
. If
you have changed the password, enter your new password and click
Login
.
Figure 7
Login Screen

Rate

3.5 / 5 based on 2 votes.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top