19216811.live➊
➐
➋
➌
➍ ➎
➏
➑
Getting to Know Your Device
Setting Up Your Device
Connecting to Your Device
Advanced Users
Troubleshooting
For Your Safety
Connection Scenario
Charging Your Device
Inserting the Battery
1.
Remove the back cover.
2.
Insert the battery as shown, with
the contacts located against the
metal springs, and press the
battery down into the case.
3. Close the back cover.
Inserting a microSDHC Card
NOTE: This device uses a microSDHC card.
1.
Pull the microSDHC card cover out of the card slot.
NOTE: Pull the cover gently, as it is connected to the device.
2.
Insert a microSDHC card (not included) into the microSDHC slot.
The following picture shows the correct inserting direction. You will
hear a click when the microSDHC card locks in place.
3. Close the microSDHC card cover.
Powering On/Off Your Device
Press and hold the
Power Button
to power the device on or off.
NOTE: The device is powered on when the LCD screen lights up.
Verifying IP Address and DNS
The following steps and figures reflect configuration for the Wireless
Internet Protocol for your connections with a Windows
®
XP operating
system. To connect to MAC operating systems, refer to the device’s
user manual section
Advanced Users—Setting Up Your White List
for
Authorized Devices.
NOTE: Wireless Network Connection is used for Wi-Fi connection.
1. Right-click
My Network Places
, and then select
Properties
.
2. Right-click
Wireless Network Connection
, and then select
Properties
.
3. Select
Internet Protocol (TCP/IP)
, and then click
Properties
.
4. Select
Obtain an IP address automatically
and
Obtain DNS
server address automatically
, and then click
OK
to finish the
configuration.
1. Power on your device. It will take 1-2 minutes to initialize.
2. Use your normal Wi-Fi application to search for available
wireless networks.
NOTE: To obtain an IP address automatically, refer to the section
Advanced Users—Verifying IP Address and DNS.
3. Select the SSID of your device, and then click
Connect
.
NOTE: Please check the label on your device or select
Device Info
on the LCD screen to get the default SSID.
4. Your computer or other Wi-Fi enabled device will then connect to
the Z288L device.
The following picture is an example of device connection. All of these
devices can surf the Internet at the same time.
NOTE: You can only use Wi-Fi to connect to the Z288L device. Make
sure the devices you wish to connect to the Z288L device support Wi-Fi.
Accessing the Internet
1. Power on the Z288L device.
2. Connect your computer or other Wi-Fi enabled device to the
Z288L device.
3. After the devices are successfully connected, you can access the
Internet automatically.
NOTE: To change the Z288L device’s settings, log in to the
configuration page at
or
http://mobile.hotspot
.
Copyright © 2014 ZTE CORPORATION
All rights reserved.
No part of this publication may be excerpted, reproduced, translated
or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without the prior written
permission of ZTE Corporation.
The quick start guide is published by ZTE Corporation. We reserve the
right to make modifications on print errors or update specifications
without prior notice.
microSDHC logo is a trademark of SD-3C, LLC. Qualcomm
®
Gobi
technologies are products of Qualcomm Technologies, Inc. Other
trademarks and trade names are the property of their respective owners.
Version No.: R1.0
Edition Time: July 2014
NOTE:
Do not use the device in an enclosed environment or where heat
dissipation is poor. Prolonged work in such space may cause excessive
heat and raise ambient temperature, which may lead to automatic
shutdown of the device for your safety. In the case of such event, cool
the device in a well-ventilated place before turning on for normal use.
Problem
Suggested Solution
Cannot
establish the
Wi-Fi connection
between the Z288L
device and your
Wi-Fi enabled
device.
• Make sure the Wi-Fi function is active.
• Refresh network list and select the correct
SSID.
• Check the IP address to make sure your device
can obtain an IP address automatically in the
Internet protocol (TCP/IP) properties.
• Type the correct network key (Wi-Fi password)
when you connect to the Z288L device.
Your connected
device cannot
access the
Internet.
• Make sure your SIM card is installed.
• Change the location to find a place with a good
signal.
• Contact your service provider.
Cannot access the
web configuration
page.
• Enter the correct address. The default address
is
or
http://mobile.hotspot
.
• Only use one network adapter in your PC.
• Do not use any proxy server.
About the
password
• Select
Device Info
on the LCD screen to check
the currently setup password or check the label
on the device to get it (if you never changed the
original password).
For more assistance, please:
• Visit
www.ztedevice.com
To the Owner
•
Some electronic devices, such as the electronic system of vehicles, are susceptible
to electromagnetic interference sent by your device if inadequately shielded. Please
consult the manufacturer of your device before using if necessary.
•
Operating your device may interfere with medical devices like hearing aids and
pacemakers. Please always keep them more than 20 centimeters away from such
medical devices when they are turned on. Turn your device off if necessary. Consult
a physician or the manufacturer of the medical device before using your device.
•
Be aware of the usage limitation when using your device at places such as oil
warehouses or chemical factories, where there are explosive gases or explosive
products being processed. Turn off your device if required.
•
The use of electronic transmitting devices is forbidden in aircrafts, at gas stations,
and in hospitals. Please observe and obey all warning signs and power off your
device in these conditions.
•
Do not touch the inner antenna area if not necessary; it will affect your device’s
performance.
•
Store your device out of the reach of little children. Your device may cause injury if
used as a toy.
•
Do not touch the metallic parts of your device.
Using Your Device
•
Please use original accessories or accessories that are authorized. Using any
unauthorized accessories may affect your device’s performance, and violate related
national regulations about telecom terminals.
•
Avoid using your device near or inside metallic structures or establishments that can
emit electromagnetic waves; it may influence signal reception.
•
Your device is not waterproof. Please keep it dry and store in a shady and cool place.
•
Do not use your device immediately after a sudden temperature change. In such
case, it will produce moisture inside and outside your device. Wait until it becomes
dry.
•
Handle your device carefully. Do not drop, bend, or strike it; your device may get
damaged.
•
No dismantling by non-professionals and only qualified technicians can undertake
repair work.
•
Operating temperature range of 0±C - +35±C and humidity range of 5% - 95% are
recommended.
Battery Handling
•
Do not short-circuit the battery, as this can cause excessive heat and fire.
• Do not store battery in hot areas or dispose of it in a fire.
• Do not disassemble or modify the battery.
•
When not using the battery for a long period, remove it from your device and store it
in a cool, dry place.
• Never use a damaged or worn-out charger or battery.
•
Return the worn-out battery to the provider or put it in an approved recycling
container. Do not put it in your regular house trash.
WARNING!
If the battery is broken, keep away from it. If it touches your skin, wash
your skin with abundant fresh water and ask a doctor for help if necessary.
Radio Frequency (RF) Energy
This model device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government:
The exposure standard for wireless devices employs a unit of measurement known
as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.
Tests for SAR are conducted using standard operating positions accepted by the FCC
with the device transmitting at its highest certified power level in all tested frequency
bands. Although the SAR is determined at the highest certified power level, the actual
SAR level of the device while operating can be well below the maximum value. This is
because the device is designed to operate at multiple power levels so as to use only
the position required to reach the network. In general, the closer you are to a wireless
base station, the lower the power output.
The highest SAR value for the model device as reported to the FCC when worn on
the body, as described in this user guide, is 1.33 W/kg(CDMA BC1) (Body-worn
measurements differ among device models, depending upon available enhancements
and FCC requirements.)
While there may be differences between the SAR levels of various devices and at
various positions, they all meet the government requirement.
The FCC has granted an Equipment Authorization for this model device with all
reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines.
SAR information on this model device is on file with the FCC and can be found under
the Display Grant section of http://www.fcc.gov/oet/ea/fccid/ after searching on
FCC ID: SRQ-Z288L
.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Caution: Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Configure Your Device on the Web
Accessing the Configuration Page
1. You will need to locate your password first. This can be found under
the battery cavity. Check the label and make note of the password
to continue.
2. Make sure your device is connected to the Z288L device.
3. Launch the Internet browser and enter
or
http://mobile.hotspot
in the address bar.
NOTE: It is recommended that you use Internet Explorer
®
(7.0 or
later), Firefox
®
(15.0 or later), Opera™ (10.0 or later), Safari
®
(4.0 or
later), or Google™ Chrome™ (10.0 or later).
4. On the configuration page, select the desired language and input
the password. Click
Login
to log in to the device.
You can charge your device by using the USB cable or adapter. Please
charge your device for more than two hours when you use it the first
time or when you haven’t used it for a long time.
• Use the USB cable to connect your device and PC directly.
• Use the adapter and USB cable to connect the wall outlet and
your device.
NOTE: The plug only fits one way to connect your device. Do not use
excessive force to insert the plug.
Z079584506205
QUICK START GUIDE
Z288L
www.zteusa.com
Z079584506205
Introduction
ZTE Z288L is a 4G hotspot device, working on 1X/HRPD/eHRPD/LTE
networks. You can connect your devices to it via Wi-Fi
®
. The device
supports data services, enabling you to communicate anytime and
anywhere.
Outline and Parts
The following figure shows the appearance of the device. It is only for
your reference. The actual device may be different.
1. Power Button
2. Charger/Micro USB Port
3. Enter Key
4. Left Key
5. Right Key
6. Back Key
7. LCD Screen
8. microSDHC
™
Card Slot
➊
Power Button:
Press and hold the
Power Button
to power the
device on or off.
➋
Charger/Micro USB Port:
Charge your device.
➌
Enter Key:
Enter or select an item.
➍
Left Key:
Check the on-screen menu from right to left.
➎
Right Key:
Check the on-screen menu from left to right.
➏
Back Key:
Go back to the previous screen.
➐
LCD Screen:
Indicates the signal type, signal strength, battery,
Wi-Fi, etc.
➑
microSDHC Card Slot:
Insert a microSDHC card.
Resetting Your Device
There are two ways to reset your device.
• Select
Settings
>
Device Settings
>
Reset
. Click
Reset
>
Yes
to
set all the settings to their factory default values. The device will
restart automatically.
• Reset your device by pressing and holding the
Reset Button
.
1. Remove the back cover.
2. Find the hole marked
Reset
on the right side of the bottom of the
device.
3. Use the end of a paperclip (or other tool that fits in the hole) to
press and hold the
Reset Button
for three seconds or longer.
4. Factory reset will take effect and then the device will restart.
Indicators
When the device is powered on, the following icons will appear on the
LCD screen. The corresponding indicators are listed in the table below.
Navigating Your Device
Use the
Left
and
Right
keys to scroll to the desired menu. Press the
Enter Key
to select.
ICON
INDICATION
Network signal strength.
/
/
Network type. 3G/4G/LTE icon will appear on the LCD
screen according to the network being connected.
The device has been connected to the Internet.
Roaming network indication.
New message received.
The message inbox is full.
Wi-Fi status and number of connected users.
Battery power indication.
The battery is full.
ICON
NAME
DESCRIPTION
Device
Info
•
Network Name:
Displays the default SSID.
•
Password:
Displays your current password.
•
Web Login Screen:
Displays the login URL of the
web UI.
•
Admin Password:
Displays the default login
password of the web UI.
•
My Phone Number:
Displays your phone number.
•
Serial Number:
Displays the serial number.
•
SIM Number:
Displays the SIM number.
Connected
Device
Press the
Enter Key
to check the information about
connected devices.
Settings
•
Software Update:
Update the software.
•
Sound Alert:
Turn on or off the sound alert. It is on
by default, so you will hear an alert when there are
devices connected.
•
Screen Timeout:
Set time for screen timeout.
•
Language:
Set language for your device.
•
Wi-Fi:
You can view your Wi-Fi status and settings.
WPS
Press the
Enter Key
to launch Wi-Fi Protected
Setup.
Mobile Hotspot
Setting Up Your WPS
If your computer or other Wi-Fi enabled device supports WPS, you
don’t have to input the password manually once your WPS has been
set up in your web UI. To set up, follow these steps:
1.
Log into the web UI.
2.
Select
Settings
>
Wi-Fi Settings
>
Basic Settings
.
3.
Enter the Network Name (SSID) or verify it is correct.
4.
Enable
Broadcast Network Name (SSID)
.
5.
Set the
Security Mode
,
Encryption Type
, and
Password
(if needed). Refer to the table below for settings.
6. Click
Apply
to confirm the settings.
7.
Enable the Wi-Fi function on your device.
8.
Select
on the Z288L device’s LCD screen to start the Wi-Fi
Protected Setup authentication process.
9.
To respond to this authentication process, enable the WPS
function on the device you wish to connect.
10.
Follow the system prompts on your device to finish the
connection.
Security Mode
Encryption Type
Key
Password
WPS
OPEN
NO ENCRYPTION
No
No
No
OPEN
WEP
Yes
No
No
WPA2 (AES)-PSK
Not Applicable
No
Yes
Yes
WPA-PSK/WPA2-PSK
Not Applicable
No
Yes
Yes