1. Home
    2. /
  2. Manuals
    3. /
  3. ZTE
    4. /
  4. AC30
    5. /
  5. 3
Page 11 / 37 Scroll up to view Page 6 - 10
11
3. Once the battery is secure, place the battery cover back on the device until it locks into place.
4. Connect the Mini USB end of the AC wall charger to the Mini USB port on the device.
5. Plug the other end of the AC wall charger into the appropriate electrical outlet. Charge at least 5 hours to ensure a full initial
charge.
NOTE:
When device is powered on, the battery icon will be solid green notifying the user the battery is fully charged.
WARNING!
Please use only an approved charging accessory to charge your device. Improper handling of the charging port, as
well as the use of an incompatible charger, may cause damage to your device and void the warranty.
6. You are now ready to install VZAccess Manager and the drivers. In order to install VZAccess Manager and activate the
device, you must use the USB cable (included).
Installing the SIM Card*
Your wireless device comes with an installed SIM Card which, along with a Global plan on your account, enables you to access
the internet while traveling outside the U.S. in supported destinations. Should your SIM Card be lost or damaged, please follow
these instructions for the installation of your new SIM:
1.
Remove SIM Card from the outer card, beingcareful not to touch the gold contacts.
2.
Remove the battery cover from your wireless device. Remove the battery. Hold the card with the Verizon Wireless/Vodafone
logo facing you and the gold contact points properly aligned with the SIM Card slot.
9
3.
Insert SIM Card into the slot. The SIM Card may remain in the wireless device permanently once installed (No need to remove).
Page 12 / 37
12
:
Should your SIM Card be lost or damaged please call 1-800-922-0204 to speak with a Customer Service Representative. From
outside the U.S. call + 1-908-559-4899 for 24/7 Global Support.
*Your SIM (Subscriber Identity Module) Card is a small rectangular plastic card that stores your phone number and important
information about your wireless service.
CAUTION:
Do not bend or scratch your SIM Card. Avoid exposing your SIM Card to static electricity, water or dirt.
IMPORTANT:
Prior to using GlobalAccess service outside of the U.S., you must:
1.
Ensure VZAccess Manager is properly installed on your computer.
2.
Ensure a Global
Access
service plan is activated on your Fivespot.
Connection options
There are two connection options for this device:
z
USB Mode
:
Connect the device to your notebook via the included USB cable, then power on your device.
.
z
Wi-Fi mode
: Power on directly without connecting to notebook. See figure below.
Page 13 / 37
13
NOTE:
±
Connect up to five Wi-Fi–enabled devices at once.
±
Plug the device directly into a wall outlet or laptop USB port to extend usage time.
Setting up the Fivespot for the First Time
VZ
Access Manager must be installed prior to activation of your device. The first time you use the
device,
VZ
Access Manager must be installed.
VZ
Access Manager installation
Getting started with your new wireless device is simple. All you have to do is connect your device to a USB port on your
notebook computer using the USB cable included with your device. VZAccess Manager Installer auto-launches and the drivers
install automatically once installation is complete. And with the new VZAccess Manager software automatically included with
your installation, you’ll find that your wireless device is just as easy to use as it is to install.
In most operating systems, VZAccess Manager will launch automatically on your screen once the software is properly installed. (If VZAccess Manager does not open automatically,
you can launch it from your Start menu. Refer to software User Guide for complete details.)
Install
VZ
Access Manager and drivers with the USB cable before installation
IMPORTANT:
Installation must be performed via the USB cable prior to activation.
IMPORTANT:
Before installing your new software, uninstall any previous version of
VZ
Access Manager and drivers using the
proper Add/Remove Programs steps per your operating system.
Windows
1.
Turn on your computer and close all open applications. Make sure your Fivespot is off.
2.
Insert the USB cable into the Mini USB port on your device and the other end into the USB port of your computer.
3.
To turn your Fivespot on, press and hold the Power button until the signal icon is lit.
VZAccess Manager Installer launches and the device drivers automatically install (this may take a few moments). If VZAccess
Page 14 / 37
14
Manager does not automatically install, go to
Start >My Computer
and click to open the CD-ROM drive with the Verizon
Wireless icon. Double click on
setup.exe
and wait a few moments for the software and drivers to automatically install.
4.
Launch VZAccess Manager. The first time you launch VZAccess Manager, the Setup Wizard appears. Follow the on-screen
instructions to configure the device. When prompted select
Auto Detect
or
USB Modem
as device type.
5.
Select
Verizon Wireless
--VZ
Access
from the available networks and select
Connect WWAN
. Follow the onscreen prompts
6.
If your device was not activated prior to installation of VZAccess Manager, the software will connect to the
Verizon Wireless
activation website
. Follow the on-screen instructions to complete the activation.
7.
Setup is now complete.
18 THE BASICS
Macintosh
1.
Turn on your computer and close all applications. Make sure your Fivespot is off.
2.
Insert the USB cable into the Mini USB port on your device and the other end into the USB port of your computer.
3.
To turn your Fivespot on, press and hold the Power button until the signal icon is lit. The VZAccess Manager CD icon appears.
Click to open and select VZ
Access Manager
to launch the installer. Follow the on-screen instructions to install the software and
drivers. After theinstallation is complete, your Mac will re-start.
19HE BASICS
4.
Launch VZAccess Manager. The first time you launch VZAccess Manager the VZAccess Manager Setup Wizard appears.
Following the on-screen instructions to configure the device. When prompted select
USB Modem
as device type.
5.
Select
Verizon Wireless
--VZ
Access
from the available networks and select
Connect WWAN
. Follow the onscreen prompts.
6.
If your device was not activated prior to installation of VZAccess Manager, the software will connect to the
Verizon Wireless
activation website
. Follow the on-screen instructions to complete the activation.
7.
Setup is now complete.
Page 15 / 37
15
Connecting to the Internet
With your new wireless device and your computer, a wireless Internet connection can always be at your fingertips.
Refer to the User Guides on your device to see how easy it is to get connected. The
Fivespot
may be used with or without the
USB cable. There are two methods to connect the device to your computer: USB cable or Wi-Fi.
NOTE
:
The Fivespot needs to be manually powered off then powered on in order to switch between USB and Wi-Fi
connection modes. When the Fivespot is powered on after connecting with the computer, it will be in USB mode.
When the Fivespot is powered on without connecting to the computer, it will be in Wi-Fi mode.
Connecting your device with the USB cable
When you connect using the USB cable and then power ON the Fivespot, the following should occur:
• The
turns on (green).
• If you are in 3G coverage, the 3G icon will turn green.
21S
• Launch VZAccess Manager (if not open already) to connect to Mobile Broadband.
Unplugging your device when connected with the USB cable
1.
End your Internet session by selecting
Disconnect
from VZAccess Manager.
2.
Exit VZAccess Manager.
3.
Simply pull the USB cable from your computer and press and hold the
POWER
button to power off your Fivespot.
Connecting your device via Wi-Fi (no USB Cable)
NOTE:
It is recommended the battery be fully charged in order to use the Fivespot in Wi-Fi mode for the first time, or
connect the Fivespot to an AC outlet using the AC wall charger provided.
Ensure the power is off and that the USB cable is NOT connected to the computer. The following should occur after you press
and hold the
Power
button:
• Your device is powered on and the Signal icon lights up.
• Once your device is powered and has been activated, it automatically connects to the Internet, provided that Mobile Broadband

Rate

4.5 / 5 based on 2 votes.

Popular ZTE Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top