1. Home
    2. /
  2. Manuals
    3. /
  3. ZoneAlarm
    4. /
  4. Z100G
    5. /
  5. 18
Page 86 / 428 Scroll up to view Page 81 - 85
Using Internet Setup
72
Check Point ZoneAlarm User Guide
New fields appear, depending on the check boxes you selected.
2.
Click
Apply
.
The ZoneAlarm router attempts to connect to the Internet, and the Status Bar displays
the Internet status “Connecting”. This may take several seconds.
Once the connection is made, the Status Bar displays the Internet status “Connected”.
Page 87 / 428
Using Internet Setup
Chapter 5: Configuring the Internet Connection
73
Using a Telstra (BPA) Connection
Use this Internet connection type only if you are subscribed to Telstra® BigPond™
Internet. Telstra BigPond is a trademark of Telstra Corporation Limited.
1.
Complete the fields using the relevant information in
Internet Setup Fields
on
page 75.
Page 88 / 428
Using Internet Setup
74
Check Point ZoneAlarm User Guide
New fields appear, depending on the check boxes you selected.
2.
Click
Apply
.
The ZoneAlarm router attempts to connect to the Internet, and the Status Bar displays
the Internet status “Connecting”. This may take several seconds.
Once the connection is made, the Status Bar displays the Internet status “Connected”.
Configuring No Connection
1.
In the
Port
drop-down list, select
None
.
The fields disappear.
2.
Click
Apply
.
Page 89 / 428
Using Internet Setup
Chapter 5: Configuring the Internet Connection
75
Table 14: Internet Setup Fields
In this field…
Do this…
PPP Settings
Username
Type your user name.
Password
Type your password.
Confirm password
Type your password.
Service
Type your service name.
If your ISP has not provided you with a service name, leave this field
empty.
Server IP
If you selected PPTP, type the IP address of the PPTP server as given
by your ISP.
If you selected Telstra (BPA), type the IP address of the Telstra
authentication server as given by Telstra.
Obtain IP address
automatically
(using DHCP)
Clear this option if you do not want the ZoneAlarm router to obtain an IP
address automatically using DHCP.
IP Address
Type the static IP address of your ZoneAlarm router.
Subnet Mask
Select the subnet mask that applies to the static IP address of your
ZoneAlarm router.
Default Gateway
Type the IP address of your ISP’s default gateway.
Connect on
demand
Select this option if you do not want the router to be constantly connected
to the Internet. The router will establish a connection only under certain
conditions.
Page 90 / 428
Using Internet Setup
76
Check Point ZoneAlarm User Guide
In this field…
Do this…
On outgoing
activity
Select this option to specify that the router should only establish a
connection if there is outgoing activity (that is, packets need to be
transmitted to the Internet). If the connection times out,
the router will
disconnect.
Idle timeout
Type the amount of time (in minutes) that the connection can remain idle.
Once this period of time has elapsed, the router will disconnect.
The default value is 1.
Delay before
connecting
Type the amount of time (in seconds) that the router should wait to re-
connect to the Internet, if the connection goes down.
If you have an unstable Internet connection that tends to go down and
then return almost immediately, this setting allows you to avoid
unnecessary and costly dialing during outage periods, by deferring re-
connection for a few seconds.
The default value is 0.
Name Servers
Obtain Domain
Name Servers
automatically
Clear this option if you want the ZoneAlarm router to obtain an IP
address automatically using DHCP, but not to automatically configure
DNS servers.
Obtain WINS
Server
automatically
Clear this option if you want the ZoneAlarm router to obtain an IP
address automatically using DHCP, but not to automatically configure the
WINS server.
Primary DNS
Server
Type the Primary DNS server IP address.

Rate

3.5 / 5 based on 2 votes.

Popular ZoneAlarm Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top