1. Home
    2. /
  2. Manuals
    3. /
  3. ZoneAlarm
    4. /
  4. Z100G
    5. /
  5. 11
Page 51 / 428 Scroll up to view Page 46 - 50
Router Installation
Chapter 3: Installing and Setting Up ZoneAlarm
37
Figure 6: Typical Connection Diagram
Page 52 / 428
Router Installation
38
Check Point ZoneAlarm User Guide
Cascading Your Router
The ZoneAlarm router protects all computers and network devices that are connected to its
LAN
ports. If desired, you can increase the router's port capacity by cascading hubs or
switches.
To cascade the ZoneAlarm router to a hub or switch
1.
Connect a standard Ethernet cable to one of the router's
LAN
ports.
The ZoneAlarm router automatically detects cable types, so you can use either a
straight-through or crossed Ethernet cable.
2.
Connect the other end of the cable to an Ethernet hub or switch.
3.
Connect additional computers and network devices to the hub or switch as
desired.
Preparing the Router for a Wireless Connection
To prepare the ZoneAlarm
router for a wireless connection
1.
Connect the antennas that came with your ZoneAlarm
router to the
ANT1
and
ANT2
antenna connectors in the router's rear panel.
2.
Bend the antennas at the hinges, so that they point upwards.
Page 53 / 428
Setting Up the ZoneAlarm Router
Chapter 3: Installing and Setting Up ZoneAlarm
39
Connecting the Router to Network Printers
You can connect network printers to your ZoneAlarm Z100G router.
To connect network printers
1.
Connect one end of a USB cable to a
USB
port at the back of the unit.
If needed, you can use the provided USB extension cord.
2.
Connect the other end to a printer or a USB 2.0 hub.
Warning:
Verify that the USB devices' power requirement does not exceed the
router's USB power supply capabilities. Failure to observe this warning may cause
damage to the router and void the warranty.
For information on setting up network printers, see
Setting up Network Printers
on page
368.
Setting Up the ZoneAlarm Router
After you have installed the ZoneAlarm router, you must set it up using the steps shown
below.
When setting up your ZoneAlarm router for the first time after installation, these steps
follow each other automatically. After you have logged on and set up your password, the
ZoneAlarm Setup Wizard automatically opens and displays the dialog boxes for
performing the initial configuration of the router. If desired, you can exit the Setup Wizard
and perform each of these steps separately.
Page 54 / 428
Setting Up the ZoneAlarm Router
40
Check Point ZoneAlarm User Guide
Logging on to the ZoneAlarm Portal and setting up your password
Initial Login to the ZoneAlarm Portal
on page 43
Configuring an Internet connection
Using the Internet Wizard
on page 56
Setting the Time on your ZoneAlarm router
Setting the Time on the Router
on page 341
Setting up a wireless network
Configuring a Wireless Network
on page 113
Installing the Product Key
Upgrading Your Software Product
on page 335
Setting up subscription services
Connecting to a Service Center
on page 267
You can access the Setup Wizard at any time after initial setup, using the procedure below.
To access the Setup Wizard
1.
Click
Setup
in the main menu, and click the
Firmware
tab.
Page 55 / 428
Setting Up the ZoneAlarm Router
Chapter 3: Installing and Setting Up ZoneAlarm
41
The
Firmware
page appears.
2.
Click
ZoneAlarm Setup Wizard
.
The
ZoneAlarm Setup Wizard
opens with the
Welcome
page displayed.

Rate

3.5 / 5 based on 2 votes.

Popular ZoneAlarm Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top