Page 26 / 58 Scroll up to view Page 21 - 25
zNID 24xx Series
26
zNID Hardware Installation Guide
POTS (Voice) Support
SIP (RFC 3261)
SIP-PLAR
MGCP
5 REN per line, balanced Ring at 60V RMS, DTMF dialing
Multiple voice codec: G.711 (u/a-law), G.726, G.729 (A and B)
Echo Canceling, Voice Activity Detection (VAD), Comfort Noise Insertion (CNI)
Various CLASS services — Caller ID, Call Waiting, Call Forwarding, Call
Transfer, etc.
T.30 and T.38 Fax
G.711 fallback for FAX
Pulse metering
Wireless (WiFi) Support
2x2 MIMO
Antenna: 5dBi
25dBM EIRP (316mW) Maximum Tx Power
max number of subscribers: 16 per SSID
SSID support: 4
1:1 mapping of SSIDs to VLANs
WEP, WPA-PSK, WPA2-PSK (AES, TKIP)
802.1x
64 bit and 128 bit WEP support
MAC address filtering
DDNS
IPTV
IGMP multicast
IGMP snooping
Management
Zhone Management System
EZ Touch
CPE Manager
OMCI
Web UI
Command Line Interface
SNMP
Table 2:
zNID 24xx common specifications (Continued)
Specifications
Values
Page 27 / 58
zNID 24xx models
zNID Hardware Installation Guide
27
Regulatory Compliance
CE
UL
FCC Part B
Table 2:
zNID 24xx common specifications (Continued)
Specifications
Values
Page 28 / 58
zNID 24xx Series
28
zNID Hardware Installation Guide
zNID 24xx series dimensions
Figure 5:
zNID 24xx dimensions
Figure 6:
zNID fiber tray dimensions
Page 29 / 58
zNID 24xx series LEDs
zNID Hardware Installation Guide
29
zNID 24xx series LEDs
The LEDs vary depending on the model of zNID. See
zNID 24xx models
on
page 22
for a complete list of zNID models.
GPON
Figure 7:
zNID-GPON-24xx LEDS
Table 3:
zNID-GPON-24xx LEDs
LED Name
Color
Indicates
STATUS
Green: Heartbeat
(1 short blink every
5 seconds)
Normal Operation
Green: Rapid blink
(10/sec)
Unit has been reset to Factory
Defaults / is unconfigured
Green: Alternating
fast blinking and
Off (1 second rapid
blink/1 second off)
EZ Touch communications in process
Green: Slow blink
(1/second)
Remote Mgt Access (OMCI, SNMP,
HTTP, Telnet, or TR-069)
Green: On
Reboot or restart in process
Off
Power off
BATT
Yellow: On
Operating on Battery Power
Yellow: Slow blink
(1/sec)
Battery Alarm (Low Battery, Missing,
or Replace)
Off
Normal operation on AC power
ALARM
Red: On
Running on battery
Red: 50% cycle:
1
sec Rapid Blink/
1 sec Off
EZ Touch actions pending -- SW or
Config update required
Off
Normal operation on AC power
Page 30 / 58
zNID 24xx Series
30
zNID Hardware Installation Guide
WAN
Green: On
Ranged successfully
Green: Slow blink
(1/sec)
Ranging in progress
Off
Not ready for ranging or not
provisioned
CONFIG
Green: On
OMCI provisioning is complete
Green: Rapid blink
(10/sec)
OMCI provisioning is written to
FLASH
Green: Slow blink
(1/sec)
OMCI provisioning is in progress
Off
No OMCI provisioning
GE1 – GE4
Green: On
Ethernet interface link
Green: Flash
Data transmitting
Off
No link on Ethernet interface
VOICE
Green: On
Registered successfully
Green: Slow blink
(1/sec)
Off hook
Off
Registration failed or telephone
service is not provisioned
USB
Green: On
Connected
Off
No power/USB not connected
WIFI
Green: On
WIFI enabled
Green: Flash
Data transmitting
Off
WIFI disabled
WPS
Green: Long flash
Success
Green: Flash
In progress
Off
WPS disabled
VIDEO
Green: On
1550nm signal is normal and RF
video output is enabled
Green: Slow blink
(1/sec)
RF video output is enabled, but no
1550nm signal received
Off
RF video output is disabled
Table 3:
zNID-GPON-24xx LEDs
LED Name
Color
Indicates

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top